MTM800 Enhanced TETRA Mobile Terminal Installation Manual American Communication Systems Discover the Power of Communications ™ TO ORDER – VISIT http://www.ameradio.
COPYRIGHT MTM800 Enhanced Mobile Terminal Installation Manual 3 COPYRIGHT Copyrights © 2007 - 2010 by Motorola Inc. All rights reserved. No part of this manual may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Inc.
MTM800 Enhanced Mobile Terminal Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
Product Safety and RF Exposure MTM800 Enhanced Mobile Terminal Installation Manual 5 IMPORTANT SAFETY INFORMATION Icon Conventions The signal word Warning with the associated safety icon implies information that, if disregarded, could result in death or serious injury, or serious product damage. The signal word Caution with the associated safety icon implies information that, if disregarded, may result in minor or moderate injury, or serious product damage.
MTM800 Enhanced Mobile Terminal Installation Manual Product Safety and RF Exposure ADDITIONAL IMPORTANT INFORMATION FOR SERVICING AND INSTALLING THE TERMINAL Only specialized workshops should be contacted for installation, maintenance and repair work. This unit is equipped with protection fuses in the Power and Ignition Sense Cable. Replace these fuses only with the original ratings! Failure to use correct manufacturer-approved parts may result in physical damage to this unit.
DOCUMENT HISTORY MTM800 Enhanced Mobile Terminal Installation Manual 7 DOCUMENT HISTORY The following major changes have been implemented in this manual since the previous edition: Edition Description Date 6866539D30-A Initial edition Mar 2007 6866539D30-B Ferrite Clamp included Mar 2007 6866539D30-C Legacy errors corrections May 2007 6866539D30-D Changes in ferrite clamp installation Accessory part numbers updated Aug 2007 6866539D30-E Note regarding installation PIN 12 description corre
MTM800 Enhanced Mobile Terminal Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
CONTENTS MTM800 Enhanced Mobile Terminal Installation Manual 9 CONTENTS COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Computer Software Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MTM800 Enhanced Mobile Terminal Installation Manual CONTENTS Model Specifications* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Model Descriptions** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Accessories-to-Model Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS MTM800 Enhanced Mobile Terminal Installation Manual 11 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connection Plan for the Junction Box Accessory Terminal . . . . . . . . . . . . . . . . . . . . . Connection Plan for Accessory Connector Kit (GMBN1021). . . . . . . . . . . . . . . . . . . .
MTM800 Enhanced Mobile Terminal Installation Manual CONTENTS Equipment Electrical Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Normal Load Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Fuse Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCOPE MTM800 Enhanced Mobile Terminal Installation Manual 13 SCOPE Scope of This Manual This manual is intended for use by service technicians familiar with similar types of equipment. It contains information required for the installation of the equipment described and is current as of the printing date. Changes which occur after printing date may be incorporated by a complete Manual revision or alternatively as additions. The mobile terminal has to be installed by trained service personnel only.
MTM800 Enhanced Mobile Terminal Installation Manual MTM800 Enhanced Manuals and User Guides Installation Instructions 6866539D30 MTM800 Enhanced Installation Manual (English) Service Manual 6866539D28 MTM800 Enhanced Basic Service Manual (English) Quick Start Guides 68015000276 68015000277 68015000278 68015000279 68015000280 68015000281 68015000275 68015000274 68015000244 68015000241 68015000234 68015000227 68015000224 68015000221 68015000222 68015000303 68015000304 68015000305 68015000312 MTM800 En
SCOPE MTM800 Enhanced Mobile Terminal Installation Manual 15 Warranty and Service Support Motorola offers long term support for its products. This support includes full exchange and/or repair of the product during the warranty period, and service/ repair or spare parts support out of warranty. Prior to shipping any terminal back to the appropriate Motorola warranty depot, please contact Customer Resources or your Motorola dealer, distributor or reseller.
MTM800 Enhanced Mobile Terminal Installation Manual SCOPE Service Information Europe, Middle East and Africa Region EMEA Systems Support Centre (ESSC) The EMEA Systems Support Centre provides a remote Technical Support Service to help customers resolve technical issues and quickly restore networks and systems. This team of highly skilled professionals is available to customers with current service agreements in place that include the Technical Support Service.
SCOPE MTM800 Enhanced Mobile Terminal Installation Manual 17 Material Authorisation number. The equipment should then be shipped to the following address unless advised otherwise. Motorola GmbH, European Systems Component Centre, Am Borsigturm 130, 13507 Berlin, Germany Contact details: Email: ESCC.admin@motorola.
MTM800 Enhanced Mobile Terminal Installation Manual SCOPE Asia, Pacific Region Piece Parts Some replacement parts, spare parts, and/or product information can be ordered directly. If a complete Motorola part number is assigned to the part, it is available from Motorola Radio Aftermarket and Accessory Division (AAD). If no part number is assigned, the part is not normally available from Motorola.
SCOPE MTM800 Enhanced Mobile Terminal Installation Manual Latin America Region Latin America Radio Support Centres The Customer Support is available through the following service centres: Warranty and Repairs: MOTOROLA DE COLOMBIA SERVICE CENTRE Torre Banco Ganadero Carrera 7 No. 71-52 Torre B piso 13 Oficina 1301 Bogota - Colombia (571) 376-6990 MOTOROLA DE MEXICO SERVICE CENTRE Bosques de Alisos #125 Col.
MTM800 Enhanced Mobile Terminal Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
MODEL INFORMATION & ACCESSORIES MTM800 Enhanced Mobile Terminal Installation Manual 21 MODEL INFORMATION & ACCESSORIES MTM800 Enhanced Mobile Terminal Model Information This manual applies to the following Mobile Terminal Models Type No. Sales Model No.
MTM800 Enhanced Mobile Terminal Installation Manual MODEL INFORMATION & ACCESSORIES Model Specifications* GENERAL ETSI: RECEIVER ETS 300 394-1 Type Number: MTM800 ENH 410-470 MHz MTM800 ENH 806-870 MHz MTM800 ENH 350-390 MHz MTM800 ENH 380-430 MHz Power Supply: Minimum: Nominal: Maximum: Max. Current Superheterodyne Frequency Range: MT512M MT712M MT812M MT912M Temperature Range for Transceiver: Operating Storage: Receiver Type: TRANSMITTER MTM800 ENH MTM800 ENH MTM800 ENH MTM800 ENH 10.
MODEL INFORMATION & ACCESSORIES MTM800 Enhanced Mobile Terminal Installation Manual Model Descriptions** Model Description M1 Dash Mount with Mobile Terminal with Direct Mount Enhanced Control Head, Speaker, Microphone or Handset, Standard User Guide, and Installation Accessories. M2 Desk Mount with Mobile Terminal with Direct Mount Enhanced Control Head, Speaker, Microphone or Handset, Standard User Guide, Installation Accessories and Tray with a Power Supply.
MTM800 Enhanced Mobile Terminal Installation Manual MODEL INFORMATION & ACCESSORIES Accessories-to-Model Chart ACCESSORIES Control Heads Part Number M1 M2 M3 M4 Enhanced Control Head, English Keypad GMWN4298 X X Enhanced Control Head, Chinese Keypad GMWN4299 X X Enhanced Control Head, Korean Keypad GMWN4300 X X Enhanced Control Head, Arabic Keypad GMWN4301 X X Enhanced Control Head Bopomofo Keypad GMWN4302 X X Enhanced Control Head Cyrillic Keypad GMWN4303 X X Enhanced Co
MODEL INFORMATION & ACCESSORIES MTM800 Enhanced Mobile Terminal Installation Manual 25 ACCESSORIES Speaker, 13W GMSN4066 X X X X Speaker Extension Cable GMKN4084 X X X X M1 M2 M3 M4 X X X X Handset Part Number Telephone-Style Handset 2 GMUN1006 Impress GCAI Handset 3 HLN7016 PTT Switches Part Number X M1 M2 M3 M4 External PTT with Emergency Footswitch RLN4836 X X X X Footswitch with Remote PTT RLN4856 X X X X Pushbutton with Remote PTT RLN4857 X X X X M1
MTM800 Enhanced Mobile Terminal Installation Manual MODEL INFORMATION & ACCESSORIES ACCESSORIES Installation Part Number M1 M2 M3 M4 M5 External Alarm Relay GKN6272 X X X X Accessory Connector Kit GMBN1021 X X X X Buzzer Kit GLN7282 X X X X M1 M2 M3 M4 M5 Mounting (Transceiver) Part Number Key Lock Mount RLN4779 X X X X X High Profile Mounting Bracket GLN7317 X X X X X Low Profile Mounting Bracket GLN7324 X X X X X Mounting Frame to Install Transcei
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 27 INSTALLATION Introduction General Information This product must be installed in a vehicle in accordance with the vehicle manufacturer’s guidelines and the instruction detailed in this manual. Only the specified Motorola parts in this manual should be used. Failure to do so could result in non compliance to the Automotive Directive (72/245/EEC, as amended by 95/54/EC).
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION In a vehicle with an airbag, make sure that the mounting location of the mobile terminal, or of any terminal accessory, is not in the deployment path of the air bag. Uninstaling the radio OPTION 1: Before disconnecting the 13.2 V main power supply from the radio: 1. Switch off the radio. 2. Wait for a minimum of 4 seconds after the radio switch is released. 3. Disconnect the 13.2 V main power supply.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 29 * For more information refer to section “Ignition Sense Cable Installation”. The Ignition Sense Cable allows the terminal to be turned on and off by the vehicle ignition switch. In cases of blown fuses, replace ONLY with those of identical value. NEVER insert ones of different values. Installation Procedure Begin the DC power cable installation as follows: 1.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Locate a good vehicle ground point. The vehicle frame provides the best ground. Optimum terminal performance can only be achieved with a very low resistance ground connection. Verify that the connections between the battery negative terminal, vehicle chassis, and engine block have low resistance. Fuse (10 A) Fuse Holder Adapter Cover Red Lead Red Lead (min. 2.5 mm2) Mounting Hole Red Lead (min. 2.5 mm2) Ring Lugs Black Lead (min. 2.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 31 Ignition Sense Cable Installation Table 2 Ignition Sense Cable Number Description HKN9327 Ignition Sense Cable with fuse 4 A 6580283E02 Fuse 4 A for Ignition Sense Cable Rating Ignition Sense Cable, Length: 3 m The HKN9327 Ignition Sense Cable allows the terminal to be turned on and off by the vehicle ignition switch. The ignition sense cable kit contains a thin cable and a fuse holder.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Terminal Installation Enhanced Control Head Installation The Enhanced Control Head can be removed from the housing and turned to any position within a 180° radius. This provides multiple mounting options for the terminal. For example, the terminal may be mounted on either side of the vehicle to facilitate the safest and most ergonomically ideal position. The Enhanced Control Head may then be turned to provide the most convenient access.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 33 Trunnion Installation Installation Planning The trunnion allows the terminal to be mounted to a variety of surfaces. 1. The trunnion must be securely fixed to the vehicle chassis. 2. Ensure the surface can support the weight of the terminal. 3. Although the trunnion can be mounted to a plastic dashboard, it is recommended that the mounting screws be located so they penetrate the supporting metal frame of the dashboard.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Installation Procedure 1. Select either the transmission hump or an open underneath portion of the dash to mount your terminal (see Figure 7). When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected. 2. Use the trunnion mounting bracket as a template, to mark the hole positions on the mounting surface.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 35 Dashboard Installation Installing the Radio in an Automotive Dashboard 1. Open out the radio cut-out in the dashboard. 2. Remove the top plastic cover off the radio. 3. Insert the mounting frame into the cut-out and retain it by bending back the relevant fixing tabs, using all 6 where possible, to hold it in place. The tabs are easily bent back by twisting a large flatbladed screwdriver into the slot behind the tabs.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION 1 Figure 8 Mounting the Radio into the Frame (Shown with Enhanced Control Head) Table 3 DIN Mount Kit Components Item 1 Description Part Number DIN Mount Kit PMLN5094 Demount Tool 8166514A01
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual Remove the Radio from the Frame 1. Remove both rubber side caps from the Enhanced Control Head. 2. Insert the demount tool into the two openings as shown in Figure 9 below. Figure 9 Removing the Radio from the Frame 3. Push the demount tools through the openings in the frame. 4. Slide out the radio.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Desktop Installation The MTM800 Enhanced may be desktop mounted. The Desktop Station option provides the terminal with the desk microphone, power supply, desk top tray (without speaker) and external loudspeaker. If an outdoor antenna is used a proper grounded Lightning Protector with Quarter-Wave Shorting Stub must be inserted between the outdoor antenna and the transceiver antenna input.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 39 Wall Outlet Line Cord with Ground Power Supply 12 V Desktop Power Cable Outdoor Antenna Lightning Protector with Quarter-Wave Shorting Stub Speaker Desk Microphone CCCCCCCC CCCC CCCC CCCCCCC CCC or Antenna Cable Indoor Antenna Antenna Connector BNC C CCCCC CCC CC CCC CCC CC CCC CC Radio in Desktop Tray Figure 10 Desktop Mounting (See Table 4 for Part Numbers) Table 4 Associated Components Item Description Part Number 1
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Remote Mount Installation Remote Mount Cable Transceiver Toroid 10x 10-Pin Connector 10-Pin Connector Flex Remote Head Enhanced or Data Expansion Head Enhanced Remote Mount Enhanced Control Head Toroid 10x Figure 11 Remote Mount Installation with Remote Head Enhanced/Data Expansion Head Enhanced Table 5 Associated Components for Remote Mount Item Description Part Number 1 Remote Mount Cable, 3 m RKN4077 2 Remote Mount Cable
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 41 Installing the Remote Mount Enhanced Control Head onto the Remote Mount Trunnion 1. Slide the Remote Mount Enhanced Control Head onto the mounting trunnion until it snaps into place. 2. Tighten the screws at both sides of the trunnion. After a few turns, tilt the control head for an optimum view of the display. Then, complete the tightening of the screws. 1 1 .
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Installing the Remote Mount Enhanced Control Head in a DIN Mount Bracket 1. Slide the Remote Mount Enhanced Control Head onto the DIN Mount Bracket until it snaps into place. 2. Tighten the screws at both sides of the DIN Mount Bracket. 5 15 2 76.5 +/ 15 0.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 43 Inserting the Remote Mount Enhanced Control Head with the DIN Mount Bracket into the DIN Frame 1. Insert the mounting frame into the DIN Mount Bracket and retain it by bending back the relevant fixing tabs. Use all 6 tabs, if necessary, to hold it in place. The tabs are easily bent back by twisting a large flatbladed screwdriver into the slot behind the tabs.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Adding Extra Connectivity to the Remote Head The Accessories Expansion Cable (PMKN4029/PMKN4056) allows users to have extra connectivity to accessories via the Mobile Microphone Port (MMP) and USB port. Accessories Expansion Cable (PMKN4029/PMKN4056) Mobile Microphone Port/USB Port Module Figure 15 The Accessories Expansion Cable with the Mobile Microphone Port (MMP)/USB Port Module Installing the Accessories Expansion Cable 1.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 45 Motorcycle Mount Enhanced Control Head Installation Figure 16 Motorcycle Mount Enhanced Control Head - Front Side The keypad labelling of the control head may vary according to the specific customer/country concerns. Planning Planning is the key to fast, easy radio installation. Before a hole is drilled or a wire is run, inspect the vehicle and determine how and where you intend to mount the antenna, radio, and accessories.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION If an additional GPS antenna or a combined TETRA/GPS antenna is used, the antenna housing carries the GPS receiver. Take care not to cover the antenna housing with metal or other radio wave absorbing material.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual Figure 18 Upward Movement Figure 19 Downward Movement 47
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Mechanical Parts 1 2 2 +/-0 155 33 mm .1 m m 3 Figure 20 Motorcycle Mount Enhanced Control Head Mounted in a Trunnion Table 8 Motorcycle Mount Enhanced Control Head - Mechanical Parts List for Installation Item Description Part Number 1 Motorcycle Mount TELCO Cable PMKN4030 2&3 Motorcycle Trunnion Kit PMLN5092 Installation of the Motorcycle Mount TELCO Cable (PMKN4030) 1.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 49 Data Expansion Head Enhanced Installation Data Expansion Head Enhanced Radio without Control Head The Data Expansion Head Enhanced can be used without a control head. This configuration allows the use of the radio without any control head, allowing the radio to be powered on via the ignition switch. The packet data/SDS via the AT commands are available from the 9-pin subD connector (PEI).
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Data Expansion Head Enhanced with 3rd Party Control Head The Data Expansion Head Enhanced can be used with a “virtual head” on a PC or a third party control head. This configuration allows the controlling of the radio (Transceiver Box) with a Control Terminal (for example: Personal Computer, Laptop, Console, and so forth). In this configuration, the Control Terminal is a substitute for the Enhanced Control Head.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual Data Box Radio This configuration allows the controlling of the radio (Transceiver Box) via PEI (for example: Personal Computer, Laptop, Console, and so forth) with AT Commands (recommended) or TNP1 protocol from a Control Terminal. In this configuration, the Data Terminal is a substitute for the Enhanced Control Head.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Junction Box Installation Speaker to MTM800 Enhanced accessory connector External PTT To Ignition switch Visor microphone GMMN4065 F2 4A Connecting cable GMKN4192/3/4 External alarm Emergency switch Fist Microphone GMMN4063 or Telephone style handset GMUN1006 Junction Box GMNL3002 Accessory Connector Kit GMBN1021 Programming Cable FLN9636 CPS Standard RS232 cable Laptop Laptop Figure 23 Remote Mount Installation with Junct
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 53 Service The junction box PCB is not repairable. Please order a new junction box as necessary. Connections 1. Connect all accessories to the junction box. 2. Connect the mobile-terminal-to-Junction box cable to the junction box. 3. Connect the programming cable to the junction box (if required). 1 = Connecting cable from Junction Box to MTM800 Enhanced (rear side accessory connector) for installation purpose only.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION 4 = Connector for programming cable FLN 9636 5 = Connector for accessory connector kit GMBN1021 6 = Connector for adapting a laptop via RS232 cable 7 6 5 7 = TELCO-connector for fist microphone (GMMN4063) or telephone style handset (GMUN1006) 4 Figure 25 Connectors on the Junction Box - Rear Panel Connection Plan for the Junction Box Accessory Terminal Connection Plan for the Speaker 1 2 External Speaker 1 2 3 4 5 6 7 JUNCT
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 55 Connection Plan for the Alarm Relay BUZZER BLK 5 RED +12V ALTERNATIVE 1 2 3 4 External alarm 5 6 5 BLK 7 +12 V JUNCTION BOX TERMINAL ALTERNATIVE 5 +12 V RED 86 87 85 30 RED ALARM RELAY RED BLK +12 V +12 V BLK 86 87 85 30 RED ALARM RELAY +12 V BLK Connection Plan for the Emergency Switch 1 2 3 4 5 6 EMERGENCY SWITCH 7 JUNCTION BOX TERMINAL Connection Plan for the Ignition Sense Cable TO IGNITION
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION To install the cable, carry out the following steps. 1. Connect the stripped lead of the fuse holder cable only to an ignition switched terminal of the fuse block. Use the supplied terminal or any other suitable terminal. 2. Mount the fuse holder using the mounting hole, and dress wires as required. 3.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 57 Connection Plan for Accessory Connector Kit (GMBN1021) Part Number/Description Cable Connectivity GMSN4066 Speaker 13W GMSN4078 Speaker 5W SPKR- 1 SPKR+ 16 GMMN4065 Visor Microphone Cannot be used if connector 7 (TELCO) is in use. MIC 2 GND 7 RLN4856 Footswitch PTT RLN4857 Push button PTT RLN4858 Gooseneck PTT These accessories can be used for PTT or Emergency function.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Standard Radios without Data Expansion Head Enhanced For standard MTM800 Enhanced mobile terminals without a Data Expansion Head Enhanced, the jumper between pins 6 and 15 of the junction box (connector 5) should be removed.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 59 Connectors and Pin Assignment of the Radio Transceiver Rear Side - Pin Function 20 2 4 19 1 3 6 8 10 12 14 16 18 5 7 9 11 13 15 17 Accessory Connector *Note the location of Pin 1 Figure 26 Location of Accessory Connector - Rear Side This section gives a description of the Accessory Connector pin functions. The accessory connections shown are not compatible to some other models of Motorola radios.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Table 10 20-Pin Accessory Connector Pin Function Description 11 RX_AUDIO This is the received RX signal. Output impedance approximate 600 Ohms; unsymmetrical; Output level = 775mVRMS 12 AUDIO_PA_ENABLE This is a digital input. High level or pin enables the audio PA. Low level disables the audio PA. 13 SWB + This voltage is available when the radio is switched on. The max. current is 1.0A w/o GPS board and 0.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 61 Accessory Connection Plan The accessory connections shown are not compatible to some other models of Motorola radios. Check the appropriate accessory or technical manual for further information. Ensure correct position of the accessory connector.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Connectors and Pin Assignment of Data Expansion Head Enhanced and Remote Head Enhanced Front View CAUTION: NOT a Microphone Connector 1 2 3 4 5 6 7 8 9 10 1 13 25 14 J302 10-Pin TELCO Connector 25-Pin subD Connector 1 5 9 6 9-Pin subD Connector Figure 27 Data Expansion Head Enhanced - Front View and Connector Location Front View CAUTION: NOT a Microphone Connector 10-Pin TELCO Connector J302 10 9 8 7 6 5 4 3 2 1
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 63 Table 11 10-Pin TELCO Connector Pin Function Description 10 Analog Ground Analog Ground 9 FLT_A+ This voltage is at battery voltage level and is available as long as the radio is connected to the supply voltage. The maximum current is 300mA. A fuse in the radio prevents further circuit damage in case of shorting this pin to ground. 8 SCI_TX This if for communication between the radio and the Enhanced Control Head.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Table 12 25-Pin subD Connector Pin Function Description 10 NC Not Connected 11 NC Not Connected 12 SW_B+ Switched UB +/100mA 13 SB9600_BUS- SB9600 BUS- 14 ON_OFF_CONTROL/ FLASH_MODE This input is intended to switch the terminal into flashing & programming mode. When the terminal is switched off and this pin is connected with pin 6 (FLT A+), the terminal switches on and enters flashing & programming mode.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 65 9-Pin subD Connector The pin assignment of this 9-pin subD connector will follow the requirements of an RS232 standard interface with RS232 voltage level. The cable (see section “Connecting Cables” on page 69) which has to be used is a standardized serial interface cable which allows to connect a data device with an RS232 Interface such as for example PC, Laptop, Console.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Connector and Pin Assignment of the Enhanced Control Head Flex Cable o Pin 12 Front View of the Mobile Microphone Port (MMP) Connector 1 2 5 6 9 10 3 4 8 7 Figure 29 View of the Enhanced Control Head’s Mobile Microphone Port Connector and Flex Cable The keypad labelling of the control head may vary according to the specific customer/country concerns.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 1 10 67 10-Pin Telco Connector 1 13 25-Pi n Back Connector 25 14 Figure 30 View of the Enhanced Control Head’s rear connectors Table 15 10-Pin Telco Connector Telco Connector Pin Function Description 1 AUDIO + Balanced Audio + (Bidirectional) 2 SPKR + Speaker + 3 BUS + Serial Bus, Data sent from the Enhanced Control Head 4 AUDIO - Balanced Audio - (Bidirectional) 5 SPKR - Speaker - 6 GND Ground 7 ON_OFF_CONTRO
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Table 16 25-Pin Back Connector Back Connector Pin Function Description Default 5 VBUS_1B GCAI PIN 6: 5V Supply Disabled 6 REAR_D - GCAI PIN 4: USB D -, GPIO_2 (Shared with the front MMP) Disabled 7 REAR_D + GCAI PIN 8: USB D +, GPIO_1 (Shared with the front MMP) Disabled 8 GPIO_0 GCAI PIN 10: GPIO Input: GCAI detection / Select Line 9 VBUS_2 Second USB 5 V Supply Disabled 10 TX 4-wire RS232 TX 11 RX 4-wire RS
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual Connecting Cables Motorcycle Mount Enhanced Control Head-to-Remote Head Enhanced/Data Expansion Head Enhanced (Motorcycle Mount TELCO Cable) Part Number: PMKN4030 Length: 2.3 m (7.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Remote Mount Enhanced Control Head/Motorcycle Mount Enhanced Control Head-to-Accessories (Accessories Expansion Cable) Part Number: PMKN4029/PMKN4056 Mobile Microphone Port subD Connector USB Connector Figure 32 Connecting Cable - Accessories Expansion Cable Table 17 Accessories Expansion Cable, Connector Pin Function USB A JACK 1 2 3 4 Signal subD 25 Pos VBUS DD+ Ground 9 22 21 18 1_WIRE GPIO_3 (PTT) Speaker to Headset GPIO_2 (
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 71 Radio-to-Junction Box Part Number: 3066537B01 Length: 6 m (19.69 feet) JUNCTION BOX CONNECTOR 26-Pin subD MTM800 ACCESSORY CONNECTOR 20-Pin AMP From (Signal Name) Pin Wire Gage Wire Colour TWISTED PAIR 16 SPKR + 20 11 To (Signal Name) Pin TWIST / 25.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Data Expansion Head Enhanced Radio-to-Data Device This is a standardized RS232 cable (will not be provided by Motorola). Use the 9-pin socket on the front side of the Data Expansion Head Enhanced Radio to connect this cable with the data device. Figure 34 Standardized RS232 Cable The Data Expansion Head Enhanced has a protection grade of IP54.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 73 Data Expansion Head Enhanced Radio-to-Fist Microphone The GMKN4072 Connecting Cable replaces the existing coiled cord cable of the fist microphone (Motorola P/N: GMMN4063). Operation The crimped wires of the cable have to be connected into the 16-pin Accessory Connector (delivered with speaker GMSN4066) and than plugged into the 20-pin connector on the rear side of the radio.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION Radio-to-Data Device: Active Data Cable The GMKN1022 Active Data Cable provides a 5-wire RS232 interface (for example, RxD, TxD, CTS, RTS, DTR) between a computer and a mobile radio. The cable has to be connected to the 20pin Accessory Connector on the rear side of the radio and into the 9-pin connector of a Data Device (for example, PC, Laptop, console) The GMKN1022 Active Data Cable is not repairable.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 75 Vehicle Antenna Installation Mobile Radio Operation and EME Exposure To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit only when people inside and outside the vehicle are at least the minimum distance away from a properly installed, externallymounted antenna.
MTM800 Enhanced Mobile Terminal Installation Manual 6. INSTALLATION Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, and so forth) in close proximity to the antenna can cause severe receiver interference. The MTM800 Enhanced mobile terminal has the option of a GPS board.
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual External Speaker Installation 1. Remove the speaker from the trunnion bracket by loosening the two wing screws. 2. Choose a place to mount the speaker. When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected. 3. Use the trunnion bracket as a template to mark the positions of the mounting holes. 4.
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 79
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 81
MTM800 Enhanced Mobile Terminal Installation Manual INSTALLATION
INSTALLATION MTM800 Enhanced Mobile Terminal Installation Manual 83
MTM800 Enhanced Mobile Terminal Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK
UPGRADING THE TERMINAL MTM800 Enhanced Mobile Terminal Installation Manual 85 UPGRADING THE TERMINAL Upgrade Procedure from MTM800 to MTM800 Enhanced Existing users of the MTM800 can upgrade their equipment with the Enhanced Control Head. The different procedures below detail the software upgrade as well as the hardware changes required. From an MTM800 Dash/Desk Radio to an MTM800 Enhanced Dash/Desk Radio 1. Upgrade the software on the transceiver.
MTM800 Enhanced Mobile Terminal Installation Manual UPGRADING THE TERMINAL From an MTM800 Remote Radio to an MTM800 Enhanced Remote Radio 1. Upgrade the software on the transceiver. To use the software upgrade feature on the CPS, choose MR7.4 SW or subsequent (see "Using the MR7.4 or Subsequent Software" on page 88). 2.
UPGRADING THE TERMINAL MTM800 Enhanced Mobile Terminal Installation Manual 87 From an MTM800 Motorcycle Radio to an MTM800 Enhanced Motorcycle Radio 1. Upgrade the software on the transceiver. To use the software upgrade feature on the CPS, choose MR7.4 SW or subsequent (see "Using the MR7.4 or Subsequent Software" on page 88). 2. Replace the control head with a Motorcycle Mount Enhanced Control Head: Description 3.
MTM800 Enhanced Mobile Terminal Installation Manual UPGRADING THE TERMINAL Using the MR7.4 or Subsequent Software 1. Install the latest version of the MR7.4 or subsequent CPS. 2. Copy the software image from the released CD to the default software path. 3. Run the CPS, click Tools > Options to open the Options dialog. Set “Default Software Path” to contain the new software archive file. 4. Connect the MTM800 to the computer using a flashing cable. Power up the computer to enter bootstrap mode.
UPGRADING THE TERMINAL 6. MTM800 Enhanced Mobile Terminal Installation Manual Power off the MTM800.
MTM800 Enhanced Mobile Terminal Installation Manual UPGRADING THE TERMINAL
PRODUCT SPECIFIC INFORMATION MTM800 Enhanced Mobile Terminal Installation Manual 91 APPENDIX Product Specific Information for Digital Terminals Type MT912M/MT812M/MT712M/MT512M This section gives the Service Personnel an overview about product specific notes. This is necessary to take special precautions to avoid the introduction of hazards when operating, installing, servicing or storing equipment. This terminal meets the applicable safety standards if it is used as described.
MTM800 Enhanced Mobile Terminal Installation Manual PRODUCT SPECIFIC INFORMATION Fuse Identification In case of blown fuses during the installation replace ONLY with those of identical value. Never insert ones of different values.