WT4070/90 Wearable Terminal User Guide
WT4070/90 Wearable Terminal User Guide 72E-87633-03 Rev.
ii WT4070/90 Wearable Terminal User Guide © 2006-8 Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 09/25/2006 Initial Release -02 Rev. A 02/22/2007 Add new start up windows, Fusion 2.5 information, 128 MB Flash configuration. -03 Rev. A 05/06/2008 Add OEM version 05.30.000 information. Add freezer pouch information.
iv WT4070/90 Wearable Terminal User Guide
Table of Contents Patents.................................................................................................................................................. ii Revision History.................................................................................................................................... iii About This Guide Introduction ...........................................................................................................................................
vi WT4070/90 Wearable Terminal User Guide Keypads ............................................................................................................................................... Two-color Alphanumeric Keypad ................................................................................................... Triple-Tap Alphanumeric Keypad .................................................................................................. Display ................................................
Table of Contents vii Chapter 4: Maintenance & Troubleshooting Introduction .......................................................................................................................................... Maintaining the Wearable Terminal ..................................................................................................... Wrist Mount Cleaning Instructions ................................................................................................. Battery Safety Guidelines .
viii WT4070/90 Wearable Terminal User Guide
About This Guide Introduction This guide provides information about using the WT4070/90 family of mobile terminals and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation set for the WT4070/90 is divided into guides that provide information for specific user needs. • Microsoft Application Guide - describes how to use Microsoft developed applications.
x WT4090 Wearable Terminal User Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads WT4070 WLAN: 802.11b/g WPAN: Bluetooth 2.8” QVGA Color 128 MB RAM/ 64 MB Flash Optional accessory Windows CE 5.0 Professional Two-color or Triple-tap Alphanumeric Keypad WT4090 WLAN: 802.11a/b/g WPAN: Bluetooth 2.8” QVGA Color 128 MB RAM/ 64 MB Flash or 128 MB RAM/ 128 MB Flash Optional accessory Windows CE 5.
About This Guide Software Versions This guide covers various software configurations and references are made to operating system or software versions for: • OEM version • Fusion version. OEM Software To determine the OEM software version: 1. Press CTRL and then ESC to open the Start menu. 2. Using the navigation keys, select Settings. 3. Press the Blue key and the down arrow to open the Control Panel sub-menu. 4. Press ENTER key to launch Control Panel. 5.
xii WT4090 Wearable Terminal User Guide Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started, provides information on getting the wearable terminal up and running for the first time. • Chapter 2, Using the Wearable Terminal, explains how to use the wearable terminal. This includes instructions for powering on and resetting the wearable terminal, entering and capturing data.
About This Guide xiii • WT4090 Windows® CE 5.0 Regulatory Guide, p/n 72-86718-xx • WT4090 Wearable Terminal Integrator Guide, p/n 72E-87638-xx • RS309 Scanner Quick Reference Guide, p/n 72-86011-xx • RS409 Scanner Quick Reference Guide, p/n 72-86010-xx • Wireless Fusion Enterprise Mobility Suite User Guide for Version 2.XX, p/n 72E-107170-xx • Symbol Application Guide for Symbol Devices, p/n 72E-68901-xx • Microsoft Applications for Windows Mobile and CE 5.
xiv WT4090 Wearable Terminal User Guide
Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the wearable terminal and explains how to install and charge the batteries and start the wearable terminal for the first time.
1-2 WT4070/90 Wearable Terminal User Guide Table 1-1 Parts of the WT4070/90 Item Description Display Displays the application and data stored on the device. Power Button Places the wearable terminal in to the suspend mode or resumes normal operation. Performs a warm boot when held down for five seconds. See Resetting the Wearable Terminal on page 2-14 for information about performing a warm boot. Charge Status LED Indicates the charging status of the battery. Speaker Provides audio playback.
Getting Started 1-3 Accessories Table 1-2 lists the major accessories available for the wearable terminal: Table 1-2 Wearable Terminal Accessories Accessory Description Single Slot USB Cradle Charges the wearable terminal main battery and a spare battery. It also synchronizes the wearable terminal with a host computer through a USB connection. Four Slot Ethernet Cradle Charges up to four wearable terminals (with main battery installed) and provides communication through an Ethernet connection.
1-4 WT4070/90 Wearable Terminal User Guide Protective Cap Scan LED Trigger Connector Interface Connector Exit Window Trigger Cable Scan Button Interface Cable Figure 1-3 RS309 Scanner
Getting Started 1-5 Getting Started In order to start using the wearable terminal for the first time: • Install the main battery • Charge the main battery and backup battery • Install the wearable terminal onto the wrist mount • Install an optional scanner • Start the wearable terminal. NOTE The main battery can be charged before or after installation into the wearable terminal.
1-6 WT4070/90 Wearable Terminal User Guide Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 4-2. Charging the Main Battery and Memory Backup Battery Before using the wearable terminal for the first time, charge the main battery until the amber Charge Status LED remains lit (see Table 1-3 on page 1-6 for charge status indications).
Getting Started 1-7 Charging Spare Batteries Use the following accessories to charge spare batteries: • Single Slot USB Cradle • Four Slot Spare Battery Charger. To charge a spare battery: 1. Ensure the accessory used to charge the spare battery is connected to the appropriate power source. 2. Insert the spare battery into the accessory’s spare battery charging slot with the charging contacts facing down (over the charging pins) and gently press down on the battery to ensure proper contact. 3.
1-8 WT4070/90 Wearable Terminal User Guide Installing the Wrist Mount The wrist mount provides the mounting of the wearable terminal on the forearm for hands-free applications. Refer to the Wrist Mount Installation Guide for information on the wrist mount. Mounting Bracket Release Lever Figure 1-6 Wrist Mount To install the wrist mount: 1. Determine which arm the wrist mount will be used on. 2. Install the short strap on the end closest to the wrist. 3. Install the long strap on the other end. 4.
Getting Started 1-9 Figure 1-8 Wearable Terminal and Wrist Mount To remove the wearable terminal from the wrist mount, press down on the release lever and slide the wearable terminal out.
1 - 10 WT4070/90 Wearable Terminal User Guide Connecting a Scanner The RS309 and RS409 scanners can be used with the wearable terminal. Refer to RS309 Scanner on page 3-9 and RS409 Scanner on page 3-7 for procedures for connecting the scanner to the wearable terminal. Starting the Wearable Terminal Press the Power button to turn on the wearable terminal. If the wearable terminal does not power on, perform a cold boot. See Resetting the Wearable Terminal on page 2-14.
Chapter 2 Using the Wearable Terminal Introduction This chapter explains the physical buttons and controls on the wearable terminal, and provides basic instructions for using the wearable terminal, including powering on and resetting the wearable terminal, using a headset, entering information and scanning. This chapter also details the operation of the Windows CE 5.0 operating system including the desktop, applications and settings.
2-2 WT4070/90 Wearable Terminal User Guide LED Indicators The Charge Status LED indicates the WT4090 charging status when the WT4090 is in a cradle. Table 2-1 describes the Charge Status LED indications. Charge Status LED Figure 2-2 Charge Status LED Table 2-1 Charge Status LED Indications LED State Indication Off Wearable terminal is not in cradle. Wearable terminal not placed correctly. Charger is not powered. Slow Blinking Amber Main battery in wearable terminal is charging.
Using the Wearable Terminal 2-3 Keypads The wearable terminal has the following keypads: • Two-color alphanumeric keypad • Triple-tap (cell phone like) alphanumeric keypad. Two-color Alphanumeric Keypad The two-color alphanumeric keypad contains application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function keys (blue, orange and gray).
2-4 WT4070/90 Wearable Terminal User Guide Table 2-2 Two-color Alphanumeric Keypad Descriptions (Continued) Key Description Scroll Keys Moves up or down from one item to another or increases/decreases specified values. Moves left or right from one item to another when used with the Blue key. For each left or right scroll, the Blue key must be pressed first. ESC Exits the current operation. Alphanumeric In default state, produces the numeric value on the key.
Using the Wearable Terminal 2-5 Triple-Tap Alphanumeric Keypad The triple-tap alphanumeric keypad contains application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function keys (blue and orange). Note that keypad functions can be changed by an application so the wearable terminal’s keypad may not function exactly as described. See Table 2-3 on page 2-5 for key and button descriptions and Table 2-4 on page 2-6 for the keypad’s special functions.
2-6 WT4070/90 Wearable Terminal User Guide Table 2-3 Triple-tap Alphanumeric Keypad Descriptions (Continued) Key Description Alphanumeric In default state, produces the numeric value on the key. In Alpha state, produces the lower case alphabetic characters shown in orange text. For example, press and release the Orange key and then press the 5 key twice to produce the lowercase letter ‘k’. When the SHIFT key is pressed in Alpha state, the upper case alphabetic characters on the key are produced.
Using the Wearable Terminal Table 2-4 Special Character Generation Map (Continued) Special Character Two-color Keypad Triple-tap Keypad .
2-8 WT4070/90 Wearable Terminal User Guide Table 2-4 Special Character Generation Map (Continued) Special Character Two-color Keypad Triple-tap Keypad } (close curly bracket) Shift - Blue - Orange - 3 Shift - Blue - Orange - 3 | (pipe) Shift - Blue - Orange - 4 Shift - Blue - Orange - 4 ~ (tilde) Shift - Blue - Orange - 5 Shift - Blue - Orange - 5 < (less than sign) Shift - Blue - Orange - 6 Shift - Blue - Orange - 6 > (greater than sign) Shift - Blue - Orange - 7 Shift - Blue - Orange -
Using the Wearable Terminal 2-9 Display The wearable terminal is factory installed with the Windows CE 5.0 operating system. When the wearable terminal starts, it automatically launches the Start Up application. NOTE A customer specific application can be configured to automatically start-up and the Windows CE 5.0 desktop and Start Up application might not be visible or accessible. Start Up Window The Start Up window allows the user to launch specific applications by using the keypad.
2 - 10 WT4070/90 Wearable Terminal User Guide Windows CE 5.0 Desktop The following paragraphs describe the Windows CE 5.0 desktop. Depending upon the customer’s configuration of the wearable terminal, the desktop may not be available. Status Icons The Taskbar at the bottom of the window displays the active programs, current time, battery status and communication status.
Using the Wearable Terminal 2 - 11 Table 2-6 Status Icons (Continued) Status Icon Description Wireless connection status icon. Indicates WLAN signal strength. Indicates that the SHIFT key is selected. Indicates that the Blue key is selected. Indicates that the CTRL key is selected. Indicates that the ALT key is selected. Indicates that the Orange key is selected. Indicates that the Gray key is selected.
2 - 12 WT4070/90 Wearable Terminal User Guide 2. Press the up arrow until the Programs item is highlighted. 3. Press the Blue key and the down arrow to open the Programs sub-menu. 4. Press the down arrow until Windows Explorer is highlighted. 5. Press ENTER key to launch Windows Explorer. Selecting Items When using the navigation keys to perform tasks in an application, the active item is highlighted using either a color background and/or a dashed box.
Using the Wearable Terminal 2 - 13 Selected Tab Figure 2-9 Navigating Tabs Navigating Fields To navigate from one field to another, press the TAB key. Repeated pressing of the TAB key cycles the highlighted cursor through the fields in the window. Selecting Checkboxes and Radio Buttons To select or deselect checkboxes and radio buttons press the TAB key until the field is highlighted. Press ALT BKSP (SPACE) to select or deselect the checkbox or radio button.
2 - 14 WT4070/90 Wearable Terminal User Guide 4. Repeat step 3 to move to the desired item. 5. Press SPACE to highlight the item. 6. Repeat steps 3 through 5 until all items are selected. 7. Perform the desired function. Resetting the Wearable Terminal There are two types of resets, warm boot and cold boot. A warm boot restarts the wearable terminal by closing all running programs. A cold boot also restarts the wearable terminal, but erases all stored records and entries in RAM.
Using the Wearable Terminal 2 - 15 Data Capture Wearable terminals used with an optional wearable laser scanner allow collection of data by scanning one dimensional bar codes. Laser Scanning Wearable terminals with an optional wearable laser scanner have the following features: • Reading of a variety of bar code symbologies, including the most popular linear, postal, and 1-D code types. • Advanced intuitive laser aiming for easy point-and-shoot operation.
2 - 16 WT4070/90 Wearable Terminal User Guide Figure 2-11 Laser Scanner Aiming Pattern Release the trigger. 4. Scanning Tips Optimal scanning distance varies with bar code density and scanner optics. • Hold the scanner farther away for larger symbols. • Move the scanner closer for symbols with bars that are close together. NOTE Scanning procedures depend on the application and wearable terminal configuration. An application may use different scanning procedures from the one listed above.
Using the Wearable Terminal 2 - 17 Waking the Wearable Terminal The wake up conditions define what actions wake up the wearable terminal after it has gone into suspend mode. The wearable terminal can go into suspend mode by either pressing the Power button or automatically by control panel time-out settings. These settings are configurable and the factory default settings are shown in Table 2-9. Table 2-9 Wakeup Default Settings Condition for Wakeup Power Button Automatic Time-out AC power is applied.
2 - 18 WT4070/90 Wearable Terminal User Guide
Chapter 3 Accessories Introduction The wearable terminal accessories provide a variety of product support capabilities. Accessories include cradles, cables and scanners. Cradles • Single Slot USB cradle charges the wearable terminal main battery and a spare battery. It also synchronizes the wearable terminal with a host computer through either a serial or a USB connection.
3-2 WT4070/90 Wearable Terminal User Guide Single Slot USB Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 4-2. This section describes how to use a Single Slot USB cradle (Figure 3-1) with the wearable terminal. For USB communication setup procedures refer to the WT4090 Integrator Guide.
Accessories 3-3 • Synchronizes information between the wearable terminal and a host computer. (With customized or third party software, it can also be used to synchronize the wearable terminal with corporate databases.) • Charges the wearable terminal’s battery and a spare battery. • Provides a location for storing a scanner when a wearable terminal is docked in the cradle.
3-4 WT4070/90 Wearable Terminal User Guide Four Slot Ethernet Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 4-2. This section describes how to use a Four Slot Ethernet cradle (Figure 3-2) with the wearable terminal. For Ethernet communication setup procedures refer to the WT4090 Integrator Guide.
Accessories 3-5 Battery Charging The four slot Ethernet cradle can charge up to four wearable terminals simultaneously. To charge the wearable terminal: 1. Slide the wearable terminal into the wearable terminal slot. 2. The wearable terminal amber Charge Status LED indicates the wearable terminal battery charging status. The Standard Battery usually charges in less than four hours.See Table 3-1 for charging status indications. 3.
3-6 WT4070/90 Wearable Terminal User Guide Four Slot Spare Battery Charger CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 4-2. This section describes how to use the Four Slot Spare Battery Charger to charge up to four wearable terminal spare batteries.
Accessories 3-7 RS409 Scanner To connect the RS409 scanner to the wearable terminal: NOTE There are two RS409 configurations available. The short cable configuration connects the RS409 to the wearable terminal mounted on the arm. The extended cable configuration connects the RS409 to the WT4090 mounted on the hip. 1. Remove the rubber plug from the wearable terminal interface connector. 2. Connect the RS409 interface cable to the wearable terminal interface connector.
3-8 WT4070/90 Wearable Terminal User Guide 5. Slide the RS409 onto the index finger with the scan trigger next to the thumb. Figure 3-6 Place the RS409 on Index Finger 6. Tighten the finger strap. Figure 3-7 Tightening Straps 7. If required, cut excess finger strap material. After connecting the scanner, warm boot the wearable terminal. See Resetting the Wearable Terminal on page 2-14 for information on performing a warm boot.
Accessories 3-9 RS309 Scanner The RS309 connects to the wearable terminal and mounts on the back of either hand using the RS309 glove. 1. Remove the rubber plug from the wearable terminal interface connector. 2. Connect the RS309 trigger cable to the back of the RS309. Trigger Connector Figure 3-8 Connecting Trigger Cable to RS309 NOTE There are two interface cables available. The standard interface cable connects the RS309 to the wearable terminal mounted on the arm.
3 - 10 WT4070/90 Wearable Terminal User Guide Interface Connector Figure 3-10 Connecting Interface Cable to RS309 6. Mount the RS309 on the RS309 glove. Refer to the RS309 Glove Installation Guide for information on mounting the RS309. 7. Route the trigger cable around the side of the RS309, next to the index finger. 8. Slide the trigger mount on the index finger, with the button positioned next to the thumb, and adjust the velcro strap.
Accessories 3 - 11 Hip Mount The hip mount allows the user to mount the wearable terminal on the hip for use in voice picking applications. An RS309 or RS409 scanner with an extended cable is required when using the hip mount. Slide the wearable terminal into the hip mount. Figure 3-12 Insert Wearable Terminal into Hip Mount Close the front flap followed by the back flap. Figure 3-13 Close Hip Mount Flaps Slide a belt through the belt loop on the back of the hip mount.
3 - 12 WT4070/90 Wearable Terminal User Guide Figure 3-14 Hip Mount on Belt Connect accessories as required. Routing an Extended Cable Scanner When using an RS309 or RS409 scanner with the wearable terminal mounted on the hip, the extended cable version is required. Motorola offers for sale cable clips, which attach to clothing and hold the scanner cable so that the cable does not interfere with the user. The cable clips are similar to badge clips and can be purchased at any office supply store as well.
Accessories 3 - 13 Figure 3-16 Routing RS309 Scanner Cable from Hip to Hand
3 - 14 WT4070/90 Wearable Terminal User Guide Freezer Pouch The freezer pouch allows the user to use the wearable terminal in a freezer environment on the hip or wrist for use in voice picking applications. An RS309 or RS409 scanner with an extended cable is required when mounting the freezer pouch on the hip mount, if scanning is also part of the application.
Accessories 3 - 15 Figure 3-17 Insert Wearable Terminal into Freezer Pouch Close the front flap followed by the back flap. Figure 3-18 Close Freezer Pouch Flaps Slide a belt through the belt loop on the back of the freezer pouch. The wearable terminal can be mounted right-side up or up-side down depending upon user preference or application.
3 - 16 WT4070/90 Wearable Terminal User Guide Wired Headset You can use a mono headset with a microphone for audio communication with an audio enabled application. The Headset Adapter is required to connect a headset with a standard 2.5 mm jack to the wearable terminal. Figure 3-19 Typical Headset Connected to Headset Adapter Refer to the WT4070/90 Integrator Guide for instructions on assembling the headset and Headset Adapter. The Headset Adapter has a clip for mounting onto the wrist mount or belt.
Chapter 4 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the wearable terminal, and provides troubleshooting solutions for potential problems during wearable terminal operation. Maintaining the Wearable Terminal For trouble-free service, observe the following tips when using the wearable terminal: • Protect the wearable terminal from temperature extremes.
4-2 WT4090 Wearable Terminal User Guide Replaceable Pad Strap Figure 4-1 Wrist Mount Soft Goods Battery Safety Guidelines • The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment. • Improper battery use may result in a fire, explosion, or other hazard.
Maintenance & Troubleshooting Troubleshooting Wearable Terminal Table 4-1 Troubleshooting the Wearable Terminal Problem Wearable terminal does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the wearable terminal. Lithium-ion battery not installed properly. Ensure battery is installed properly. See Installing and Removing the Main Battery on page 1-5. System crash. Perform a warm boot.
4-4 WT4090 Wearable Terminal User Guide Table 4-1 Troubleshooting the Wearable Terminal (Continued) Problem Wearable terminal turns itself off. A message appears stating that the wearable terminal memory is full. Cause Solution Wearable terminal is inactive. The wearable terminal turns off after a period of inactivity. If the wearable terminal is running on battery power, this period can be set to 30 sec., 1, 2, 3, 4, 5 or 6 minutes.
Maintenance & Troubleshooting Table 4-1 Troubleshooting the Wearable Terminal (Continued) Problem The wearable terminal does not accept scan input. Wearable terminal goes into IPL mode after cold boot. WLAN connection is lost when the wearable terminal is connected to a host computer using ActiveSync. Cause Solution Scanning application is not loaded. Verify that the unit is loaded with a scanning application. See the System Administrator. Unreadable bar code. Ensure the symbol is not defaced.
4-6 WT4090 Wearable Terminal User Guide Four Slot Ethernet Cradle Table 4-2 Troubleshooting the Four Slot Ethernet Cradle Problem Cause Solution Wearable terminal amber Charge Status LED does not light when wearable terminal inserted. Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. Wearable terminal is not correctly seated. Remove and re-insert the wearable terminal into the cradle, ensuring it is correctly seated.
Maintenance & Troubleshooting Four Slot Spare Battery Charger Table 4-3 Troubleshooting The Four Slot Spare Battery Charger Symptom Batteries not charging. Possible Cause Solution Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery. Battery contacts not connected to charger.
4-8 WT4090 Wearable Terminal User Guide Single Slot USB Cradle Table 4-4 Troubleshooting the Single Slot USB Cradle Symptom Possible Cause Charge Status LEDs do not light when wearable terminal or spare battery is inserted. Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. Wearable terminal is not seated firmly in the cradle. Remove and re-insert the wearable terminal into the cradle, ensuring it is firmly seated.
Maintenance & Troubleshooting Table 4-4 Troubleshooting the Single Slot USB Cradle (Continued) Symptom During data communications, no data was transmitted, or transmitted data was incomplete. Cannot ActiveSync with Host Computer Possible Cause Solution Wearable terminal removed from cradle during communications. Replace wearable terminal in cradle and retransmit. Incorrect cable configuration. See the System Administrator. Communications software is not installed or configured properly.
4 - 10 WT4090 Wearable Terminal User Guide
Appendix A Specifications Technical Specifications The following tables summarize the wearable terminal’s intended operating environment and general technical hardware specifications. Wearable Terminal The following table summarizes the wearable terminal’s intended operating environment. Table A-1 Technical Specifications Item Description Physical and Environmental Characteristics Dimensions 5.7 inches L x 3.7 inches W x 1.0 inch H (14.2 cm L x 9.3 cm H x 2.6 cm H) Weight (including battery) 11.
A-2 WT4090 Wearable Terminal User Guide Table A-1 Technical Specifications (Continued) Item Description User Environment Operating Temperature -4 °F to 122°F (-20 °C to 50 °C) Storage Temperature -40 °F to 158 °F (-40 °C to 70 °C) Battery Charging Temperature 32 °F to 104 °F (0 °C to +40 °C) ambient temperature range. Humidity 5% to 95% non condensing Drop Specification Multiple 4 ft.(1.
Specifications Table A-1 Technical Specifications (Continued) Item Description Peripherals and Accessories Cradles Single Slot USB Four Slot Ethernet Printers Supports extensive line of Symbol approved printers, cables and accessories Charger Four Slot Battery Charger Other Accessories Headset adapter to a 2.5 mm barrel jack headset connector Regulatory Electrical Safety Certified to UL60950-1, CSA C22.2 No.
A-4 WT4090 Wearable Terminal User Guide Table A-2 RS309 Technical Specifications (Continued) Item Description Pitch ± 65 degrees from normal User Environment Operating Temperature -22 °F to 122 °F (-30 °C to 50 °C) Storage Temperature -40 °F to 140 °F (-40 °C to 60 °C) Humidity 5% to 95% non condensing Drop Specification 4 ft.(1.
Specifications Table A-3 RS409 Technical Specifications (Continued) Item Description Scan Rate 104 (± 12) scans/sec (bidirectional) Nominal Working Distance Density5 mil 7.5 mil 10 mil Code Type39 39 39 Far (inches)4.758.75 13.25 Far (inches)8.7514.25 Yaw ± 50 degrees from normal Roll ± 35 degrees from vertical Pitch ± 65 degrees from normal 13 mil UPC 17.25 24.25 20 mil 39 21.5 35.75 40 mil 55 mil 39 39 22.25 27 50.
A-6 WT4090 Wearable Terminal User Guide Cradles Table A-4 Accessory Specifications Single Slot USB Cradle Four Slot Ethernet Cradle Four Slot Spare Battery Charger Operating Temperature 32 °F to 122 °F (0 °C to +50 °C) 32 °F to 104 °F (0 °C to +40 °C) Storage Temperature -40 °F to 158 °F (-40 °C to 70 °C) Battery Charging Temperature 32 °F to 104 °F (0 °C to +40 °C) ambient temperature Humidity 5% to 95% non-condensing Size (L x W x H) 6.6 in. x 5.1 in. x 3.9 in. (16.8 cm x 13.0 cm x 9.
Appendix B Regulatory Information Introduction This appendix contains the accessory power supply regulatory compliance statements. Accessory Power Supply Regulatory Compliance Table B-1 Accessory Power Supplies, Regulatory Compliance Statements Accessory Power Supplies Regulatory Compliance Statements Single Slot USB Cradle Power Supply Four Slot Battery Charger Power Supply Use only a Symbol-approved power supply output rated 12 VDC and minimum 3.3 A.
B-2 WT4090 Wearable Terminal User Guide
Glossary A API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Application Programming Interface. See API. ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language. For example, it uses escape sequences to control the cursor, clear the screen and set colors.
Glossary - 2 WT4090 Wearable Terminal User Guide Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory is used to store one ASCII character. boot or boot-up. The process a computer goes through when it starts. During boot-up, the computer can run self-diagnostic tests and configure hardware and software. C CDRH.
Glossary - 3 Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or numbers encoded within a bar code symbol. Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption and Key. Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol with a certain minimum element width. Device Configuration Package.
Glossary - 4 WT4090 Wearable Terminal User Guide Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification.
Glossary - 5 IS-95. Interim Standard 95. The EIA/TIA standard that governs the operation of CDMA cellular service. Versions include IS-95A and IS-95B. See CDMA. K Key. A key is the specific code used by the algorithm to encrypt or decrypt the data. Also see, Encryption and Decrypting. L laser scanner. A type of bar code reader that uses a beam of laser light. LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source.
Glossary - 6 WT4090 Wearable Terminal User Guide O Open Data-Link Interface (ODI). Novell’s driver specification for an interface between network hardware and higher-level protocols. It supports multiple protocols on a single NIC (Network Interface Controller). It is capable of understanding and translating any network information or request sent by any other ODI-compatible protocol into something a NetWare client can understand and process. Open System Authentication.
Glossary - 7 RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and signals used to transfer data serially from one device to another. S Scan Area. Area intended to contain a symbol. Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol. Its three main components are: 1. Light source (laser or photoelectric cell) - illuminates a bar code. 2.
Glossary - 8 WT4090 Wearable Terminal User Guide T TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork dissimilar systems. This standard is the protocol of the Internet and has become the global standard for communications. TCP provides transport functions, which ensures that the total amount of bytes sent is received correctly at the other end. UDP is an alternate transport that does not guarantee delivery.
Glossary - 9 U Visible Laser Diode (VLD). A solid state device which produces visible laser light. W Warm Boot. A warm boot restarts the wearable terminal by closing all running programs. All data that is not saved to flash memory is lost. Wearable Terminal. In this text, wearable terminal refers to the Symbol WT4090 that can be set up to communicate with a network, using wireless radio technology.
Glossary - 10 WT4090 Wearable Terminal User Guide
Index Numerics 1-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 28-key keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 four slot charge only cradle . . . . . . . . . . . . . . . . . 3-1 four slot cradles battery charging . . . . . . . . . . . . . . . . . . . . . . 3-5 four slot Ethernet cradle . . . . . . . . . . . . . . . . . . . 3-4 LED indicators . . . . . . . . . . . . .
Index - 2 WT4090 Wearable Terminal User Guide current time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 installing main battery . . . . . . . . . . . . . . . . . . . . . . . . 1-5 D K data capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x, 2-15 adjusting the distance . . . . . . . . . . . . . . . . . . . . 2-16 indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 laser scanning . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 3 S W scan status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 scan status See also data capture scanning bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 See data capture . . . . . . . . . . . . . . . . . . . . . . . . 2-15 screen Symbol splash screen . . . . . . . . . . . . . . . . . . . . 1-10 serial/USB cradle . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 WT4090 Wearable Terminal User Guide
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.symbol.com MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc.
