User Manual
Table Of Contents
- Title Page
- Quick Start Guide
- 1248 Front Panel
- 1248 Rear Panel
- 8M Front Panel
- 8M Rear Panel
- 16A Rear Panel
- 16A Front Panel
- MOTU AVB Switch
- MOTU AVB Control Web App
- Overview
- It’s not on your hard drive
- Use your favorite web browser
- Control from multiple devices
- Run the installer, get the app
- Make hardware and network connections
- Launching the web app
- Device tab
- Device tab (continued)
- Routing tab
- Mixing tab
- Aux Mixing tab
- Mixer input channel strips
- Main Mix and Monitor channel strips
- Aux bus channel strips
- Group and Reverb channel strips
- 1 About Your MOTU AVB Audio Interface
- State-of-the-art A/D and D/A conversion
- Complementary I/O configurations
- 1248
- 8M
- 16A
- Network I/O
- Universal connectivity
- On-board DSP with mixing and effects
- 32-bit floating point processing
- Modeled vintage effects processing
- AVB system expansion and audio networking
- Matrix routing and multing
- 256 channels of network audio I/O for your host computer
- Web app control
- Stand-alone mixing with wireless control
- ADAT digital I/O
- S/PDIF digital I/O with SRC
- Word clock
- Comprehensive metering
- Headphone outputs
- Precision Digital Trim™
- Rack mount or desktop operation
- AudioDesk
- 2 Packing List and System Requirements
- 3 Software Installation
- 4 Hardware Installation
- Overview
- Rack installation and heat
- Thunderbolt audio interface setup
- USB audio interface setup
- Setup for two interfaces
- Setup for three to five interfaces
- Setup for a multi-switch network
- Setup for multiple Thunderbolt and USB interfaces
- Setup for web app control
- Audio connections
- A typical 1248 setup
- A typical 8M setup
- A typical 16A setup
- Synchronization
- Syncing S/PDIF devices
- Syncing word clock devices
- Syncing an AVB network
- 5 Presets
- 6 The Front Panel LCD
- 7 Working with Host Audio Software
- Overview
- Preparation
- Run the web app
- Sample rate
- Clock Mode
- Enabling and disabling input/output banks
- Specifying the number of computer channels
- Making inputs and outputs available to your host software
- Configuration presets
- Naming computer input and output channels
- Streaming computer audio to and from the onboard mixer
- Working with AVB network streams
- Mirroring computer channels to multiple outputs
- Combining multiple inputs to one output
- Routing grid tutorials
- Choosing the MOTU Audio driver
- Reducing monitoring latency
- Working with on-board mixing and effects
- Synchronization
- 8 Mixer Effects
- 9 Networking
- A Troubleshooting
- B Audio Specifications
- C Mixer Schematics
- D Updating Firmware
- E OSC Support
- Index
![](/manual/motu/9310/user-manual-english/images/img-10.png)
8M Rear Panel
1. The 8M is equipped with an auto-switching interna-
tional power supply.
2. BNC word clock jacks. Use them for a variety of applica-
tions, such as digital transfers with devices that cannot
slave to the clock supplied by their digital I/O connection
with the 8M.
3. These ADAT optical “lightpipe” jacks provide 16 channels
of 24-bit ADAT optical digital I/O at 1x sample rates (44.1
or 48 kHz) and 8 channels at 2x sample rates (88.2 or 96
kHz). They are disabled at higher sample rates. The IN
and OUT ports on the right provide channels 1-8 (or 1-4),
and the left-hand ports provide channels 9-16 (or 5-8).
4. The 8M’s eight analog outputs are balanced TRS quarter-
inch connectors that can also accept an unbalanced plug
(with the ring disconnected). They are equipped with
very high quality 24-bit 192 kHz converters. The output
trim can be adjusted from the Output Setting section of
the Device Tab in the MOTU AVB Control web app
software.
5. These XLR/TRS combo jacks accept either a mic cable or a
quarter-inch cable, balanced or unbalanced, from a
guitar or line input. Use the front panel controls to adjust
individual preamp gain, 48V phantom power, and an
optional -20 dB pad for each mic input. The quarter-inch
plug is equipped with a high-impedance circuit for
guitar input.
6. Connect the 8M to the computer here via either
Thunderbolt or USB 2.0, using a standard Thunderbolt or
USB cable. For details, see “Setup for multiple Thunder-
bolt and USB interfaces” on page 39.
7. The AVB Ethernet port provides industry standard IEEE
802.1 network connectivity to other network devices.
Examples include:
■
Another 8M or any other MOTU AVB-equipped device,
such as the 1248 or 16A audio interfaces.
■
A standard Ethernet hub or WiFi router (for internet
connection and communication with the MOTU AVB
Control web app software).
■
A standard AVB Ethernet switch for high-speed, low-
latency, high-capacity audio connectivity to an AVB
audio network.
4 51 2 3
7 6