User Manual
Table Of Contents
- Title Page
- Quick Start Guide
- 1248 Front Panel
- 1248 Rear Panel
- 8M Front Panel
- 8M Rear Panel
- 16A Rear Panel
- 16A Front Panel
- MOTU AVB Switch
- MOTU AVB Control Web App
- Overview
- It’s not on your hard drive
- Use your favorite web browser
- Control from multiple devices
- Run the installer, get the app
- Make hardware and network connections
- Launching the web app
- Device tab
- Device tab (continued)
- Routing tab
- Mixing tab
- Aux Mixing tab
- Mixer input channel strips
- Main Mix and Monitor channel strips
- Aux bus channel strips
- Group and Reverb channel strips
- 1 About Your MOTU AVB Audio Interface
- State-of-the-art A/D and D/A conversion
- Complementary I/O configurations
- 1248
- 8M
- 16A
- Network I/O
- Universal connectivity
- On-board DSP with mixing and effects
- 32-bit floating point processing
- Modeled vintage effects processing
- AVB system expansion and audio networking
- Matrix routing and multing
- 256 channels of network audio I/O for your host computer
- Web app control
- Stand-alone mixing with wireless control
- ADAT digital I/O
- S/PDIF digital I/O with SRC
- Word clock
- Comprehensive metering
- Headphone outputs
- Precision Digital Trim™
- Rack mount or desktop operation
- AudioDesk
- 2 Packing List and System Requirements
- 3 Software Installation
- 4 Hardware Installation
- Overview
- Rack installation and heat
- Thunderbolt audio interface setup
- USB audio interface setup
- Setup for two interfaces
- Setup for three to five interfaces
- Setup for a multi-switch network
- Setup for multiple Thunderbolt and USB interfaces
- Setup for web app control
- Audio connections
- A typical 1248 setup
- A typical 8M setup
- A typical 16A setup
- Synchronization
- Syncing S/PDIF devices
- Syncing word clock devices
- Syncing an AVB network
- 5 Presets
- 6 The Front Panel LCD
- 7 Working with Host Audio Software
- Overview
- Preparation
- Run the web app
- Sample rate
- Clock Mode
- Enabling and disabling input/output banks
- Specifying the number of computer channels
- Making inputs and outputs available to your host software
- Configuration presets
- Naming computer input and output channels
- Streaming computer audio to and from the onboard mixer
- Working with AVB network streams
- Mirroring computer channels to multiple outputs
- Combining multiple inputs to one output
- Routing grid tutorials
- Choosing the MOTU Audio driver
- Reducing monitoring latency
- Working with on-board mixing and effects
- Synchronization
- 8 Mixer Effects
- 9 Networking
- A Troubleshooting
- B Audio Specifications
- C Mixer Schematics
- D Updating Firmware
- E OSC Support
- Index
HARDWARE INSTALLATION
45
A TYPICAL 8M SETUP
Here is a typical 8M studio setup. Like the 1248,
this rig can be operated without an external mixer.
All mixing and effects processing can be done in
the 8M itself, on the computer with audio software,
or both. During recording, you can use the 8M’s
on-board mixer to listen to what you are recording
via the headphone out or any output pair. You can
control all mixing and effects processing from your
laptop, tablet or smart phone.
Guitar 2
Other outputs (stage
monitors, surround
monitors, etc.)
Figure 4-7: A typical 8M studio setup.
8M front
panel
8M back
panel
MOTU 8pre and/or
other optical devices
8-channel
ADAT optical
Guitar 1
Secondary
studio monitors
Bass
Ethernet cable to another MOTU
AVB device, a MOTU AVB Switch,
or WiFi router, etc.
Thunderbolt or USB
Mac
Primary
studio monitors or
PA
Headphones