User Manual
Table Of Contents
- Title Page
- Quick Start Guide
- 1248 Front Panel
- 1248 Rear Panel
- 8M Front Panel
- 8M Rear Panel
- 16A Rear Panel
- 16A Front Panel
- MOTU AVB Switch
- MOTU AVB Control Web App
- Overview
- It’s not on your hard drive
- Use your favorite web browser
- Control from multiple devices
- Run the installer, get the app
- Make hardware and network connections
- Launching the web app
- Device tab
- Device tab (continued)
- Routing tab
- Mixing tab
- Aux Mixing tab
- Mixer input channel strips
- Main Mix and Monitor channel strips
- Aux bus channel strips
- Group and Reverb channel strips
- 1 About Your MOTU AVB Audio Interface
- State-of-the-art A/D and D/A conversion
- Complementary I/O configurations
- 1248
- 8M
- 16A
- Network I/O
- Universal connectivity
- On-board DSP with mixing and effects
- 32-bit floating point processing
- Modeled vintage effects processing
- AVB system expansion and audio networking
- Matrix routing and multing
- 256 channels of network audio I/O for your host computer
- Web app control
- Stand-alone mixing with wireless control
- ADAT digital I/O
- S/PDIF digital I/O with SRC
- Word clock
- Comprehensive metering
- Headphone outputs
- Precision Digital Trim™
- Rack mount or desktop operation
- AudioDesk
- 2 Packing List and System Requirements
- 3 Software Installation
- 4 Hardware Installation
- Overview
- Rack installation and heat
- Thunderbolt audio interface setup
- USB audio interface setup
- Setup for two interfaces
- Setup for three to five interfaces
- Setup for a multi-switch network
- Setup for multiple Thunderbolt and USB interfaces
- Setup for web app control
- Audio connections
- A typical 1248 setup
- A typical 8M setup
- A typical 16A setup
- Synchronization
- Syncing S/PDIF devices
- Syncing word clock devices
- Syncing an AVB network
- 5 Presets
- 6 The Front Panel LCD
- 7 Working with Host Audio Software
- Overview
- Preparation
- Run the web app
- Sample rate
- Clock Mode
- Enabling and disabling input/output banks
- Specifying the number of computer channels
- Making inputs and outputs available to your host software
- Configuration presets
- Naming computer input and output channels
- Streaming computer audio to and from the onboard mixer
- Working with AVB network streams
- Mirroring computer channels to multiple outputs
- Combining multiple inputs to one output
- Routing grid tutorials
- Choosing the MOTU Audio driver
- Reducing monitoring latency
- Working with on-board mixing and effects
- Synchronization
- 8 Mixer Effects
- 9 Networking
- A Troubleshooting
- B Audio Specifications
- C Mixer Schematics
- D Updating Firmware
- E OSC Support
- Index
HARDWARE INSTALLATION
46
A TYPICAL 16A SETUP
Here is a typical 16A studio setup, although the
16A is certainly flexible and supports many
operational configurations not shown here. This
diagram is meant to give you just a few ideas of
what is possible. The 16A can be used as an audio
interface, mixer, effects processor, or even as a
patch bay. You can control all mixing, effects
processing, and routing from your laptop, tablet or
smart phone.
synthesizer
quarter-inch analog outs
quarter-inch analog outs
synths, samplers, effects units, etc.
Figure 4-8: A typical 16A studio setup.
16A back
panel
Compressor, reverb or
other outboard gear
8-channel
ADAT optical
5.1 or 7.1 surround
monitoring
Secondary
studio monitors
quarter-inch analog outs
synthesizer
synthesizer
quarter-inch analog outs
Other
outputs
(send/return loop)
MOTU 8pre and/or
other optical devices
Ethernet cable to another MOTU
AVB device, a MOTU AVB Switch,
or WiFi router, etc.
Thunderbolt or USB
Mac