User Manual
Table Of Contents
- Title Page
- Quick Start Guide
- 1248 Front Panel
- 1248 Rear Panel
- 8M Front Panel
- 8M Rear Panel
- 16A Rear Panel
- 16A Front Panel
- MOTU AVB Switch
- MOTU AVB Control Web App
- Overview
- It’s not on your hard drive
- Use your favorite web browser
- Control from multiple devices
- Run the installer, get the app
- Make hardware and network connections
- Launching the web app
- Device tab
- Device tab (continued)
- Routing tab
- Mixing tab
- Aux Mixing tab
- Mixer input channel strips
- Main Mix and Monitor channel strips
- Aux bus channel strips
- Group and Reverb channel strips
- 1 About Your MOTU AVB Audio Interface
- State-of-the-art A/D and D/A conversion
- Complementary I/O configurations
- 1248
- 8M
- 16A
- Network I/O
- Universal connectivity
- On-board DSP with mixing and effects
- 32-bit floating point processing
- Modeled vintage effects processing
- AVB system expansion and audio networking
- Matrix routing and multing
- 256 channels of network audio I/O for your host computer
- Web app control
- Stand-alone mixing with wireless control
- ADAT digital I/O
- S/PDIF digital I/O with SRC
- Word clock
- Comprehensive metering
- Headphone outputs
- Precision Digital Trim™
- Rack mount or desktop operation
- AudioDesk
- 2 Packing List and System Requirements
- 3 Software Installation
- 4 Hardware Installation
- Overview
- Rack installation and heat
- Thunderbolt audio interface setup
- USB audio interface setup
- Setup for two interfaces
- Setup for three to five interfaces
- Setup for a multi-switch network
- Setup for multiple Thunderbolt and USB interfaces
- Setup for web app control
- Audio connections
- A typical 1248 setup
- A typical 8M setup
- A typical 16A setup
- Synchronization
- Syncing S/PDIF devices
- Syncing word clock devices
- Syncing an AVB network
- 5 Presets
- 6 The Front Panel LCD
- 7 Working with Host Audio Software
- Overview
- Preparation
- Run the web app
- Sample rate
- Clock Mode
- Enabling and disabling input/output banks
- Specifying the number of computer channels
- Making inputs and outputs available to your host software
- Configuration presets
- Naming computer input and output channels
- Streaming computer audio to and from the onboard mixer
- Working with AVB network streams
- Mirroring computer channels to multiple outputs
- Combining multiple inputs to one output
- Routing grid tutorials
- Choosing the MOTU Audio driver
- Reducing monitoring latency
- Working with on-board mixing and effects
- Synchronization
- 8 Mixer Effects
- 9 Networking
- A Troubleshooting
- B Audio Specifications
- C Mixer Schematics
- D Updating Firmware
- E OSC Support
- Index
HARDWARE INSTALLATION
44
A TYPICAL 1248 SETUP
Here is a typical 1248 studio setup. This rig can be
operated without an external mixer. All mixing and
effects processing can be done in the 1248 itself, on
the computer with audio software, or both. During
recording, you can use the 1248’s on-board mixing
to listen to what you are recording via the main
outs, headphone outs, or any other output pair. You
can control all mixing and effects processing from
your laptop, tablet, or smart phone.
Ethernet cable to another MOTU
AVB device, a MOTU AVB Switch,
or WiFi router, etc.
synthesizer
quarter-inch analog outs
Guitar
quarter-inch analog outs
synths, samplers, effects units, etc.
Other outputs (stage
monitors, surround
monitors, etc.)
Figure 4-6: A typical 1248 studio setup.
Headphones
1248 front
panel
1248 back
panel
Compressor, reverb or
other outboard gear
Thunderbolt or USB
MOTU 8pre and/or other
optical devices
Primary
studio monitors
Bass
Secondary
studio monitors
8-channel
ADAT optical
Mac
S/PDIF
Home theater system