User Manual
Table Of Contents
- Title Page
- Quick Start Guide
- LP32 Front Panel
- LP32 Rear Panel
- MOTU Pro Audio Control Web App
- Overview
- It’s not on your hard drive
- Use your favorite web browser
- Control from multiple devices
- Run the installer, get the app
- Make hardware and network connections
- Launching the web app
- Device tab
- Device tab (continued)
- Device tab (continued)
- Routing tab
- Mixing tab
- Aux Mixing tab
- Mixer input channel strips
- Main Mix and Monitor channel strips
- Aux bus channel strips
- Group and Reverb channel strips
- 1 About the LP32
- Comprehensive I/O
- Flexible optical I/O
- Network I/O
- Other MOTU AVB interfaces
- Universal computer connectivity
- On-board DSP with mixing and effects
- 32-bit floating point processing
- Modeled vintage effects processing
- AVB/TSN system expansion and audio networking
- Matrix routing and multing
- Web app control
- Stand-alone mixing with wireless control
- Comprehensive metering
- Headphone output
- Rack mount or desktop operation
- Audio analysis tools
- AudioDesk
- 2 Packing List and System Requirements
- 3 Software Installation
- 4 Hardware Installation
- Overview
- USB or iOS audio interface setup
- AVB Ethernet audio interface setup
- Setup for two interfaces
- Setup for three to five interfaces
- Setup for a multi-switch network
- Setup for multiple interfaces
- Setup for web app control
- Setup for AVB Ethernet audio interface operation
- Audio connections
- Synchronization
- Syncing optical devices
- Syncing word clock devices
- Syncing an AVB network
- Syncing multiple AVB audio interfaces connected to a Mac
- 5 Presets
- 6 The Front Panel LCD
- 7 Working with Host Audio Software
- Overview
- Preparation
- Run the web app
- Choose the MOTU Pro Audio driver
- Reducing monitoring latency
- Monitoring through the LP32
- Direct hardware playthrough / Direct ASIO monitoring
- Monitoring through your host audio software
- Adjusting your host software audio buffer
- Adjusting buffer size on Mac OS X
- Adjusting buffer size on Windows
- Lower latency versus higher CPU overhead
- Transport responsiveness
- Effects processing and automated mixing
- Working with the Routing grid
- Enabling and disabling input/output banks
- Specifying the number of computer channels
- Making inputs and outputs available to your host software
- Configuration presets
- Naming computer input and output channels
- Streaming computer audio to and from the onboard mixer
- Working with AVB network streams
- Mirroring computer channels to multiple outputs
- Combining multiple sources to one output
- Routing grid tutorials
- Working with on-board mixing and effects
- 8 Mixer Effects
- 9 MOTU Audio Tools
- 10 Networking
- A Troubleshooting
- B Audio Specifications
- C Mixer Schematics
- D Updating Firmware
- E OSC Support
- Index
MOTU AUDIO TOOLS
80
View controls
The View controls (Figure 9-14) provide several
options for the X-Y Plot display.
Figure 9-14: View controls.
Pausing the display
The Pause button in the upper right corner of the
View section (Figure 9-14) allows you to freeze the
display at any time. To resume, click the button
again. The level meters will remain active while the
display is paused.
Line/Scatter
Choose either Line or Scatter from the menu in the
View section (Figure 9-14) to plot each point
(sample) as either a single pixel or as a continuous
line that connects each plot point to the next, as
shown below in Figure 9-15.
Figure 9-15: The same X-Y Plot displayed in Line versus Scatter mode.
☛ Line mode is significantly more CPU intensive
than Scatter. You can reduce Line mode CPU
overhead on the X-Y Plot by reducing the Length
parameter (described below).
Color/Grayscale
In Color mode (Figure 9-14) the most recently
displayed audio data is shown in red, which fades
to yellow, green and then finally blue, before
disappearing. In Grayscale mode, data is first
shown in white and then fades to gray. To adjust the
scale of this color/brightness change, see “Decay”
on page 81.
Axes
The Axes control (Figure 9-14) sets the opacity of
the grid displayed in the graph, from 100% (fully
visible) down to 0% (fully hidden).
Horizontal and vertical controls
The Horizontal and Ve r t i c a l controls (Figure 9-16)
configure the value range of the x-axis (left channel
amplitude), and y-axis (right channel amplitude),
respectively. Click and drag the values up or down
to set them, or double-click to return to the default
value.
There are two modes for the controls: Zoom/Offset
and Min/Max. To change the mode, use the menu
shown in Figure 9-16.
Figure 9-16: Setting the Horizontal or Vertical control modes.
In Zoom/Offset mode, Zoom scales the axis. Pos
moves the lines marking x = 0 left and right, or
y = 0 up and down.
In Min/Max mode, Min and Max let you scale the
grid by moving the -1.0 and +1.0 points along the
axis. Min/Max mode lets you control the graph
boundaries directly.
Persistence
The Persistence controls (Figure 9-17) affect the
appearance of data from when it is first displayed
until it disappears from the grid.
Pause button