HDX-SDI Manual Win Page -1 Friday, April 8, 2011 11:54 AM MOTU HDX-SDI ™ User’s Guide for Windows 1280 Massachusetts Avenue Cambridge, MA 02138 Business voice: (617) 576-2760 Business fax: (617) 576-3609 Web site: www.motu.com Tech support: www.motu.
HDX-SDI Manual Win Page 0 Friday, April 8, 2011 11:54 AM About the Mark of the Unicorn License Agreement and Limited Warranty on Software TO PERSONS WHO PURCHASE OR USE THIS PRODUCT: carefully read all the terms and conditions of the “click-wrap” license agreement presented to you when you install the software. Using the software or this documentation indicates your acceptance of the terms and conditions of that license agreement. Mark of the Unicorn, Inc.
HDX-SDI Manual Win Page 1 Friday, April 8, 2011 11:54 AM Contents Part 1: Getting Started 3 Quick Reference: HDX-SDI Front Panel 4 Quick Reference: HDX-SDI Rear Panel 5 Quick Reference: MOTU Video Console 7 About the HDX-SDI 11 Packing List and System Requirements 13 Installing the HDX-SDI Windows Software 15 Installing the HDX-SDI Hardware Part 2: Using the HDX-SDI 31 HDX-SDI Basics 33 MOTU Video Console 43 Adobe Premiere Pro Part 3: Appendices 55 Troubleshooting 57 DB-25 to XLR Pin
HDX-SDI Manual Win Page 2 Friday, April 8, 2011 11:54 AM SAFETY PRECAUTIONS AND ELECTRICAL REQUIREMENTS CAUTION! READ THIS SAFETY GUIDE BEFORE YOU BEGIN INSTALLATION OR OPERATION. FAILURE TO COMPLY WITH SAFETY INSTRUCTIONS COULD RESULT IN BODILY INJURY OR EQUIPMENT DAMAGE. HAZARDOUS VOLTAGES: CONTACT MAY CAUSE ELECTRIC SHOCK OR BURN. TURN OFF UNIT BEFORE SERVICING. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE.
HDX-SDI Manual Win Page 3 Friday, April 8, 2011 11:54 AM Part 1 Getting Started
HDX-SDI Manual Win Page 4 Friday, April 8, 2011 11:54 AM
5 6 4. Keep this switch in the down position to enable AUTO ON mode.When AUTO ON mode is enabled you can leave the main power switch (item #12) on and the HDX-SDI will power up when you power on your computer and power down when you power off your computer. 3. This is a standard quarter-inch stereo headphone jack. Its output always matches analog outputs 1-2 on the rear panel. Use the volume knob to control its level. 8. This bank of audio level meters is for Bank A (channels 1-8).
2 3. If you only need two channels of AES/EBU digital audio I/O, connect them to these BNC jacks. If you need eight channels, connect a breakout cable to the DB-25 connector to the right. 2. Connect timecode input and output here, to the LTC IN and LTC OUT. The HDX-SDI supports all standard timecode formats. 1. Connect blackburst or another video reference signal to the VIDEO REF IN. If the HDX-SDI is at the end of the video sync daisy chain, flip the THRU/TERM switch to the 75Ω TERM position.
HDX-SDI Manual Win Page 7 Friday, April 8, 2011 11:54 AM Quick Reference: MOTU Video Console CHAPTER Choose the video format that you wish to capture or play back. Click a tab to view its settings above. For complete details on the settings in these tabs, see chapter 6,“MOTU Video Console” (page 35). The status area tells you what mode the HDX-SDI hardware is in. It also provides helpful troubleshooting info. When capturing video, choose the input source here.
HDX-SDI Manual Win Page 8 Friday, April 8, 2011 11:54 AM 8
HDX-SDI Manual Win Page 9 Friday, April 8, 2011 11:54 AM CHAPTER 1 About the HDX-SDI OVERVIEW The HDX-SDI is a PCI Express video interface for Windows that provides broadcast-quality video capture and monitoring for Adobe Premiere Pro.
HDX-SDI Manual Win Page 10 Friday, April 8, 2011 11:54 AM ■ Captures and plays uncompressed HD and SD — 10-bit 4:2:2 color depth and 1920 x 1080 resolution, all standard HD and SD formats up to and including 1080p30 (720p, 1080i, 1080p and 1080PsF). ■ Support for all codecs supported natively by Premiere Pro — monitor any host-based codecs supported by Premiere Pro.
HDX-SDI Manual Win Page 11 Friday, April 8, 2011 11:54 AM ■ Supported Premiere Pro HD formats — Uncompressed HD (8-bit and 10-bit), DVCProHD 720p at all eight frame rates listed above, plus DVCProHD 1080 (1280 and 1440 rasters) at all 1080 frame rates listed above Supported Premiere Pro SD formats — Uncompressed 8-bit and 10-bit, DVCPro and DVCPro 50 at 486i29.
HDX-SDI Manual Win Page 12 Friday, April 8, 2011 11:54 AM POWER ■ International auto-switching internal power supply INCLUDED SOFTWARE AND COMPATIBILITY ■ MOTU Video console software — provides complete control of all programmable features and settings. ■ Supports Premiere Pro CS5 (version 5.0.
HDX-SDI Manual Win Page 13 Friday, April 8, 2011 11:54 AM CHAPTER 2 Packing List and System Requirements PACKING LIST PLEASE REGISTER TODAY! The HDX-SDI ships with the items listed below. If any of these items are not present in your HDX-SDI box when you first open it, please immediately contact your dealer or MOTU. Please register your HDX-SDI today. There are two ways to register.
HDX-SDI Manual Win Page 14 Friday, April 8, 2011 11:54 AM 14 PACKING LIST AND SYSTEM REQUIREMENTS
HDX-SDI Manual Win Page 15 Friday, April 8, 2011 11:54 AM CHAPTER 3 Installing the HDX-SDI Windows Software IMPORTANT! INSTALL THE HDX-SDI SOFTWARE FIRST! Before you connect the HDX-SDI interface to your computer and turn it on, run the HDX-SDI Software Installer. This ensures that all the HDX-SDI components are properly installed in your system.
HDX-SDI Manual Win Page 16 Friday, April 8, 2011 11:54 AM 16 INSTALLING THE HDX-SDI WINDOWS SOFTWARE
HDX-SDI Manual Win Page 17 Friday, April 8, 2011 11:54 AM CHAPTER 4 Installing the HDX-SDI Hardware OVERVIEW ■ Static electricity occurs much more readily in dry climate conditions. If you can, perform the installation with a relative humidity of at least 50%. Here’s an overview for installing the HDX-SDI: Did you run the software installer first? . . . . . . . . . . . . . . Precautions before you begin . . . . . . . . . . . . . . . . . . . . . . . Installing the PCI Express card . . . . . . . . . . .
HDX-SDI Manual Win Page 18 Friday, April 8, 2011 11:54 AM 6 Remove the HDX-SDI PCIe card from its antistatic bag. 7 Gently but firmly insert the card into any available PCIe slot. 3 Insert the adapter into the ExpressCard slot on your laptop computer with the top of the ExpressCard adapter (the side with the label on it) facing up and the mini-HDMI connector (the smaller of the two connectors) facing out. Figure 4-2: Inserting the HDX-SDI ExpressCard adapter. Figure 4-1: Inserting the HDX-SDI PCIe card.
HDX-SDI Manual Win Page 19 Friday, April 8, 2011 11:54 AM Figure 4-3: Connecting the HDX-SDI to the computer. ☛ If you are using the HDX-SDI with an ExpressCard adapter, the included HDMI cable has a regular HDMI plug at one end and a smaller, mini-HDMI plug at the other end. Plug the miniHDMI plug into the ExpressCard adapter. Figure 4-4: Making the connection from the computer to the HDX-SDI.
HDX-SDI Manual Win Page 20 Friday, April 8, 2011 11:54 AM CONNECT VIDEO INPUTS AND OUTPUTS The HDX-SDI provides a wealth of video input and output connectivity, from consumer analog formats such as S-video and composite to broadcast formats such as HD-SDI. Support for both NTSC and PAL The HDX-SDI supports both NTSC and PAL formats on all inputs and outputs. It does not, however, convert between NTSC and PAL.
HDX-SDI Manual Win Page 21 Friday, April 8, 2011 11:54 AM connectors from component (the factory default format) to composite. See “Analog Output Mode” on page 39 for details. is connected. If the device you are connecting supports both RGB and YPbPr, use YPbPr, as it is the standard for broadcast video. Component The HD/SD Analog Video Section (Figure 4-5) provides either HD or SD component input and output. The HDX-SDI provides 10-bit analog performance with 12-bit A/D and D/A converters.
HDX-SDI Manual Win Page 22 Friday, April 8, 2011 11:54 AM HDMI The HDX-SDI provides HDMI input and output in professional, broadcast quality 10-bit 4:2:2 resolution. The input is ideal for capturing video from HDMI-equipped cameras, many of which send the video signal to their HDMI output before it is compressed in the camera. The HDMI output can be connected to any device equipped with an HDMI input, such as a plasma screen, LCD screen or even a home theater receiver.
HDX-SDI Manual Win Page 23 Friday, April 8, 2011 11:54 AM EXAMPLE HDX-SDI VIDEO CONNECTIONS Here is an example of the types of video devices that you can connect to the HDX-SDI. You can mix and match HD and SD sources and destinations, connect them all, and then choose the desired source from the MOTU Video console software. HD camera HD camera DVD Player HD-SDI OUT HD Component OUT Composite OUT HD-SDI IN SD Composite IN S-Video OUT HDMI out SD VTR (VHS, SVHS, etc.
HDX-SDI Manual Win Page 24 Friday, April 8, 2011 11:54 AM CONNECT AUDIO INPUTS AND OUTPUTS The HDX-SDI provides the following audio input and output: Audio format Input channels Output channels 96 kHz quarter-inch TRS analog 8 8 96 kHz AES/EBU on DB-25 breakout 8 8 48 kHz embedded SDI 8 8 96 kHz embedded HDMI* 8 8 Stereo AES/EBU on BNC + stereo analog on RCA 2+2 2 (AES/EBU only) *HDMI audio is stereo at sample rates above 48kHz when playing or capturing SD video.
HDX-SDI Manual Win Page 25 Friday, April 8, 2011 11:54 AM Stereo AES/EBU with sample rate conversion As shown in Figure 4-7, there are two sets of AES/EBU connectors: stereo BNC and 8-channel DB-25. The BNC input and output jacks provide stereo AES/EBU digital audio input and output via direct connection to the HDX-SDI rear panel using standard broadcast-grade BNC cables.
HDX-SDI Manual Win Page 26 Friday, April 8, 2011 11:54 AM EXAMPLE HDX-SDI AUDIO CONNECTIONS Figure 4-9 shows an example of the types of audio connections you can make between other devices and the HDX-SDI. You can mix and match analog SD camcorder and digital sources and destinations, connect them all. The 8-channel banks of AES/EBU digital I/O are ideal for connection to a digital mixer. HD camera Game console OR Digital mixer Camera Powered 5.1 or 7.
HDX-SDI Manual Win Page 27 Friday, April 8, 2011 11:54 AM VIDEO SYNC CONNECTIONS TIMECODE CONNECTIONS Connect a video sync source, such as blackburst, to the VIDEO REF IN jack (Figure 4-10). This input accepts either a Bi-level (SD) sync source or a Tri-level (HD) sync source. The HDX-SDI can resolve to a VIDEO REF IN signal only when it is in Playback mode, or when it is capturing SDI. When capturing other sources, it genlocks to the current video source, or its own Master (Internal) clock.
HDX-SDI Manual Win Page 28 Friday, April 8, 2011 11:54 AM SYNCING DIGITAL AUDIO DEVICES The HDX-SDI’s stereo BNC AES/EBU input is equipped with sample rate converters (SRC). This allows the digital audio data to be transferred cleanly, with no dropped samples, clicks, or pops , even when the two devices are not resolved to one another. However, it is still a good idea to resolve digital audio devices with the HDX-SDI during digital audio transfers to prevent audio from drifting out of sync with picture.
HDX-SDI Manual Win Page 29 Friday, April 8, 2011 11:54 AM Resolving a third device to the HDX-SDI If you need to make digital audio transfers between the HDX-SDI and third device (that is not the current video source), you must resolve the third device to the HDX-SDI, as demonstrated in Figure 4-14. In this example, the third device, a field recorder, is being resolved to the HDX-SDI via AES/EBU input.
HDX-SDI Manual Win Page 30 Friday, April 8, 2011 11:54 AM A caution about using rate conversion Rate conversion can be a life saver in situations where resolving digital audio clocks is difficult or impossible. As long as you are capturing audio and video together, audio will remain perfectly in sync with picture.
HDX-SDI Manual Win Page 31 Friday, April 8, 2011 11:54 AM Part 2 Using the HDX-SDI
HDX-SDI Manual Win Page 32 Friday, April 8, 2011 11:54 AM
HDX-SDI Manual Win Page 33 Friday, April 8, 2011 11:54 AM CHAPTER 5 HDX-SDI Basics TWO MODES The HDX-SDI provides two basic modes of operation: ■ Capture ■ Playback (monitor) The current mode is clearly indicated by the Status area in MOTU Video Console (Figure 6-1 on page 35), unless there is no genlock, in which case it will display a message explaining why not. The HDX-SDI is always either in Capture mode or Playback mode.
HDX-SDI Manual Win Page 34 Friday, April 8, 2011 11:54 AM playback decks, or DVD players, can be connected to the HDX-SDI along with multiple output devices such as monitors, recording decks, or distribution amplifiers. Choose the input source in the Setup tab in MOTU Video console, and the HDX-SDI will route that input to the corresponding outputs (either SD or HD). Choosing the current video source The MOTU Video console software lets you choose the current video source (input).
HDX-SDI Manual Win Page 35 Friday, April 8, 2011 11:54 AM CHAPTER 6 MOTU Video Console Video format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Input Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Status area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Input status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Genlock status . . . . . .
HDX-SDI Manual Win Page 36 Friday, April 8, 2011 11:54 AM VIDEO FORMAT INPUT SOURCE The Video Format setting (Figure 6-1 on page 35) shows the format in which the HDX-SDI is capturing or playing back video, and allows you to change the format manually. When capturing or playing video from Premiere Pro, this setting will be changed automatically by the host application. The Input Source menu (Figure 6-1) is important because this is where you choose the video input from which the HDX-SDI will capture.
HDX-SDI Manual Win Page 37 Friday, April 8, 2011 11:54 AM STATUS AREA SETUP TAB The Status area (Figure 6-1) displays what mode the HDX-SDI is in. It also provides helpful status information and troubleshooting suggestions. For example, if there is no video signal because of a wrong setting, the Status area will tell you which setting(s) to check. The Setup tab (Figure 6-4) provides several general settings for HDX-SDI operation.
HDX-SDI Manual Win Page 38 Friday, April 8, 2011 11:54 AM Capture Clock Source The Capture Clock Source setting (Figure 6-4) lets you specify the timing reference for the HDX-SDI when it is in Capture mode. Three choices are provided in the menu, as shown below in Figure 6-5: Clock source during capture If the input source is SDI, you can choose any of the three available clock source options. For other input formats, use either the Input Source or Master (Internal) Capture Clock Source setting.
HDX-SDI Manual Win Page 39 Friday, April 8, 2011 11:54 AM Capture and Playback modes, set the capture and playback clock sources to one of the combinations listed below: Embedded timecode from the SDI input currently chosen in the Input Source menu (Figure 6-3 on page 36).
HDX-SDI Manual Win Page 40 Friday, April 8, 2011 11:54 AM MII. Choose the format that best matches the device(s) connected to the SD component input and output. Reset to Defaults The Reset to Defaults button (Figure 6-4) restores all settings in the HDX-SDI hardware to their original (factory) values. PLAYBACK TAB The Playback tab (Figure 6-8) provides settings that apply to video playback from Premiere Pro (as opposed to capturing).
HDX-SDI Manual Win Page 41 Friday, April 8, 2011 11:54 AM Color lookup table In the Color Lookup Table (CLUT) section (Figure 6-8), there are ten parameters which define a color transfer function, as defined by the American Society of Cinematographers Color Decision List (ASC CDL) specification. The Sat parameter is ASC CDL Saturation. A value of 1.0 passes each pixel through unchanged. Values below 1.0 will desaturate, with 0.0 resulting in a monochrome image. Values greater than 1.
HDX-SDI Manual Win Page 42 Friday, April 8, 2011 11:54 AM PREVIEW TAB The Preview tab (Figure 6-10) lets you preview the video signal being received from the currently selected input in the Input Source menu (Figure 6-3 on page 36). If you don’t see the source video signal If you have trouble getting the source video signal to appear in the preview frame, make sure the Final Cut Pro Capture window isn’t open in the background.
HDX-SDI Manual Win Page 43 Friday, April 8, 2011 11:54 AM AUDIO TAB The Audio tab (Figure 6-11) provides access to the HDX-SDI’s audio features. The HDX-SDI provides 16 channels (two 8-channel banks) of simultaneous audio input and output. For a summary of audio bank formats, see “Connect audio inputs and outputs” on page 24. Sample rate Choose the audio sample rate (Figure 6-11) for capture or playback. Make sure this setting matches the rate of the audio being captured or played back.
HDX-SDI Manual Win Page 44 Friday, April 8, 2011 11:54 AM Bank A (1-8) Bank B (9-16) Figure 6-12: Input bank assignments. The first three choices are Analog (TRS), SDI/ HDMI and AES/EBU (DB-25). These are all 8channel banks. The fourth choice, AES/EBU (BNC) + Analog (RCA), is a four channel bank referring to the stereo AES/EBU BNC input on the rear panel (channels 1-2 in the bank) and the stereo RCA analog inputs on the front (channels 3-4 in the bank).
HDX-SDI Manual Win Page 45 Friday, April 8, 2011 11:54 AM CHAPTER 7 Adobe Premiere Pro OVERVIEW BEFORE YOU LAUNCH PREMIERE PRO The HDX-SDI serves as a powerful video capture and playback device for Adobe Premiere Pro. Operation is straightforward and follows the general workflow prescribed by Premiere Pro for capture procedures and time line playback. Before you launch Premiere Pro, be sure to: Familiarity with Premiere Pro . . . . . . . . . . . . . . . . . . . . . . . .
HDX-SDI Manual Win Page 46 Friday, April 8, 2011 11:54 AM GETTING STARTED 4 Name the project and click OK. 1 Launch Premiere Pro. PLAYBACK SETTINGS 2 When the Welcome screen appears, click New Project and choose the desired Capture Compression Codec from the Capture Format menu (Figure 7-1). 3 Click Configure... to access capture parameters of the HDX-SDI (Figure 7-2). If you are using a progressive 1080 line timeline, click Playback Settings to choose the desired 1080p Playback Format (Figure 7-3).
HDX-SDI Manual Win Page 47 Friday, April 8, 2011 11:54 AM most closely matches the settings you need. You can adjust settings further using the Settings tab (General tab in 5.0) and Tracks tab. Custom settings You can further adjust project settings or even create your own custom sequence presets to suit your workflow. Click the Settings tab (Figure 7-5) to further configure your settings. (This is the General tab in version 5.0.
HDX-SDI Manual Win Page 48 Friday, April 8, 2011 11:54 AM For details on other Capture settings, review chapter 6, “MOTU Video Console” (page 35). For details on other playback settings, review chapter 6, “MOTU Video Console” (page 35). Playback settings Click the Playback tab (Figure 6-8 on page 40) to view Playback settings. VIDEO CAPTURE In the Playback tab, make sure the Playback Timecode Offset and frame rate match your Premiere Pro sequence offset and frame rate.
HDX-SDI Manual Win Page 49 Friday, April 8, 2011 11:54 AM 5 Click the Logging tab (Figure 7-6) and name the clip (Figure 7-8). ☛ Be sure to name the clip before you begin capture to avoid potential issues during capture. Figure 7-7: Capture settings. 3 Choose the desired Capture Compression Codec from the Capture Format menu. 4 Click Configure... to access the capture parameters for the HDX-SDI. Refer to the following sections for information about the Capture settings (Figure 7-9 on page 50).
HDX-SDI Manual Win Page 50 Friday, April 8, 2011 11:54 AM 6 Click the Record button (Figure 7-6) to start capturing. Capture settings To access the capture settings, choose File menu> Capture to open the Capture window, click the Settings tab (Figure 7-6 on page 49), then click Configure (Figure 7-7 on page 49). Each setting is explained briefly below. Audio Inputs From the Audio Inputs menu, choose the audio channels that you wish to capture.
HDX-SDI Manual Win Page 51 Friday, April 8, 2011 11:54 AM PLAYBACK AND MONITORING To play back your Premiere Pro project and view it on any monitor or other device connected to the HDX-SDI’s video outputs: 1 Choose Edit menu > Preferences > Player Settings. 2 Choose the MOTU HDX-SDI as the Default Player (Figure 7-10). This allows you to view the Source window on any monitor connected to the HDX-SDI’s video outputs. 3 Start playback.
HDX-SDI Manual Win Page 52 Friday, April 8, 2011 11:54 AM Audio Output Mapping Audio Output Mapping (Edit > Preferences > Audio Output Mapping) lets you configure the audio output destination. Choose MOTU PCI Video ASIO to view and make changes to fit your workflow (Figure 7-12). DEVICE CONTROL TIMECODE 2 Make sure the video deck is configured properly for remote operation via RS-422 machine control.
HDX-SDI Manual Win Page 53 Friday, April 8, 2011 11:54 AM Figure 7-13: Device control. Figure 7-14: Export to Tape. EXPORT TO TAPE 3 Choose the desired Export Mode (see explanations below) and specify the insert time in the timecode field provided (Figure 7-14). The HDX-SDI provides an Export to Tape feature. This allows you to lay back material in your Premiere Pro time line to a tape deck equipped with RS-422 device (machine) control support.
HDX-SDI Manual Win Page 54 Friday, April 8, 2011 11:54 AM BATCH CAPTURE The HDX-SDI supports Premiere Pro’s Batch Capture feature, as follows: 1 In the Capture panel, use the Set In and Set Out buttons (Figure 7-15) to specify the desired log region. Figure 7-15: Logging clips. 2 Click the Log Clip button (Figure 7-15) to log the clip you specified, and name the clip when prompted. 3 When you are ready to begin, select all logged clips in the Project panel. 4 Choose File menu> Batch Capture.
HDX-SDI Manual Win Page 55 Friday, April 8, 2011 11:54 AM Part 3 Appendices
HDX-SDI Manual Win Page 56 Friday, April 8, 2011 11:54 AM
HDX-SDI Manual Win Page 57 Friday, April 8, 2011 11:54 AM APPENDIX A Troubleshooting USE THE STATUS DISPLAY Use the Status display in MOTU Video Console (Figure 6-1 on page 35) for help with various issues having to do with capture, playback, sync and other aspects of HDX-SDI operation. MOTU Video Setup is engineered to detect problems and report them in the Status area. Most common issues can be resolved by following the instructions given by the Status display.
HDX-SDI Manual Win Page 58 Friday, April 8, 2011 11:54 AM active. To activate the meters, run your video host application or MOTU Video Console and enable its audio capture features. CUSTOMER SERVICE We are happy to provide customer service to our registered users. If you haven’t already done so, please take a moment to register on line at www.motu.com/register, or fill out and mail the registration card included with your HDX-SDI.
HDX-SDI Manual Win Page 59 Friday, April 8, 2011 11:54 AM APPENDIX B DB-25 to XLR Pin Outs DB-25 TO 4 FEMALE (IN) / 4 MALE (OUT) XLR For bi-directional HDX-SDI AES/EBU digital I/O Panasonic/Tascam standard Pin Signal 1 Channel 7/8 Out (+) 2 SG (Signal Ground) 3 Channel 5/6 Out (-) 4 Channel 3/4 Out (+) 5 SG 6 Channel 1/2 Out (-) 7 Channel 7/8 In (+) 8 SG 9 Channel 5/6 In (-) 10 Channel 3/4 In (+) 11 SG 12 Channel 1/2 In (-) 13 Not used 14 Channel 7/8 Out (-) 15 Channel 5/6
HDX-SDI Manual Win Page 60 Friday, April 8, 2011 11:54 AM 60 APPENDIX B: DB-25 TO XLR PIN OUTS
HDX-SDI Manual Win Page 61 Friday, April 8, 2011 11:54 AM Index 29.
HDX-SDI Manual Win Page 62 Friday, April 8, 2011 11:54 AM installing 17 playback mode 33 software installation 15 summary of features 9 Headphone jack 5 Host LED 5 Hue option 42 Audio tab 43 Genlock indicator 35 Genlock LED 37 Genlock status 35 input indicator 37 input source menu 36 Playback tab 40 Preview tab 42 Setup tab 37 status area 37, 57 video format menu 36 Offset 40 Offset (color lookup table) 41 Outputs analog 6 machine control connector 6, 27 monitoring 51 offset 40 pausing video 40 playback
HDX-SDI Manual Win Page 63 Friday, April 8, 2011 11:54 AM connectors 21 timecode destination option 39 Sequence presets installing 15 Setup tab 37 Show Settings in Preview 50 Single Field option 40 Slope (color lookup table) 41 SMPTE timecode display 5 SMPTE/EBU N10 21 Software installation 15 Sony 9-pin connector 6, 27 9-pin setup in Premiere Pro 52 9-pin sync option 39 Beta Japan option 21, 39 Beta option 21, 39 Source LEDs 5 Speakers connecting 26 SRC 25, 28, 29 Status 57 S-video connectors 20 connector
HDX-SDI Manual Win Page 64 Friday, April 8, 2011 11:54 AM 64 I N D E X