User Manual

ManualsBrandsMountain Off Road ManualsCar8795-2

MOUNTAIN OFF ROAD ENTERPRISES. LLC.

P.O. BOX 690

DELTA, COLORADO 81416

970-625-0500

E-mail: info@mountainoffroad.com

www.mountainoffroad.com

M.O.R.E. Shackle Reversal System (S.R.S.™) # 8795-2 contains the following items:

ITEM DESCRIPTION QUANTITY PART NUMBER

A Pivot Bracket-Drivers Side 1 8795-DS

B Pivot Bracket-Pass Side 1 8795-PS

C Bushing-Aluminum 4 8795-125

D Bracket-Shackle Hanger 2 SR104

E Bolt-Shackle Hanger 3/8”x1” 2 18834

F Washers-Lock & Flat 3/8” 2 33008/33622

G Tube Spacer 3/4”x2-3/4” 1 S101299

H Tube Spacer 3/4”x2-3/8” 4 S101399

I Bolt-Spring Pivot 9/16”X4-1/2” 2 13271

J Bolt-Pivot Bracket to Frame 1/2”x4-1/2” 3 13221

K Bolt-Pivot Bracket to Frame 1/2”x1-1/4” 2 13207

L Bolt-Shackle Hanger to Frame 1/2”x4” 4 13219

M Nut-Crimp Lock 9/16” 2 37270

N Nut-Crimp Lock 1/2” 9 37268

O Washer-Flat 1/2” 20 33086

P Washer-Flat 9/16” 4 33088

- Instruction Sheet 1 8795-2 IS

Photo of items on page 2 of these instructions. Please familiarize yourself with all components in the system.

These instructions will refer to items by letter, not description. Read all instructions carefully before work is

started on your vehicle. In addition to basic hand tools, the following specialty tools are needed to perform this

installation: Angle head drill (electric or air), 3/4” diameter drill bit, 1/2” diameter drill bit, 21/64” drill bit, 3/8-24

(fine thread) tap, floor jack, jack stands (4), torque wrench, grinder and or cutting torch.

8795-2 PAGE 1

INSTALLATION INSTRUCTIONS FOR 8795-2

PLEASE READ AND UNDERSTAND TERMS/POLICIES BEFORE YOU INSTALL THIS SYSTEM

FIT and TOLERANCES: All parts in this system are the results of countless hours of research, testing, fitting

and refining. Jeep® frames have a wide tolerance on bolt hole centers from frame to frame. This is why

M.O.R.E.™ has installed several “slots” in which to mount our bracketry. In addition to the factory tolerances,

most people install other then factory equipment such as bumpers, winch mounts, springs etc. M.O.R.E.™ has

done the best job we can to insure that our parts fit with the different possibilities. However, you may find it nec-

essary to grind, elongate, bend, or force the parts in this system to fit on your rig. Please use common sense

when installing these parts, and understand that if you modify them in any way, they are not returnable!!

Summary of content (9 pages)

PAGE 1
MOUNTAIN OFF ROAD ENTERPRISES. LLC. P.O. BOX 690 DELTA, COLORADO 81416 970-625-0500 E-mail: info@mountainoffroad.com www.mountainoffroad.com INSTALLATION INSTRUCTIONS FOR 8795-2 PLEASE READ AND UNDERSTAND TERMS/POLICIES BEFORE YOU INSTALL THIS SYSTEM M.O.R.E. Shackle Reversal System (S.R.S.
PAGE 2
8795-2 S.R.S.
PAGE 3
8795-2 S.R.S.™ - GENERAL INFORMATION: This system will fit Jeep® YJ Wrangler vehicles with any engine. This system will lift the front of the Jeep® one inch (1”) over where it sits now. Before starting this installation, check the frame to make sure it is in good condition, is straight and has no excessive rust. Only install it on vehicles in good sound condition. This system will work with stock or most aftermarket bumpers, with or without a winch. No welding is required for installation.
PAGE 4
STEP BY STEP INSTALLATION INSTRUCTIONS: STEP 1: On a flat, level, hard surface (concrete) floor, jack up the Jeep® and support the frame with jack stands six inches behind the stock spring hanger (pivot end of spring). Remove the wheels. Remove the plastic front frame cover. SEE FIGURE 1. STEP 2: Using a second set of jack stands, support the front axle under the rotor/hub area. There should be a slight bit of weight on the stands. SEE FIGURE 2. STEP 3: Remove the front drive shaft. Remove the front bumper.
PAGE 5
STEP 10: Find items “D” and install the bushings and sleeves that you removed from the stock shackle hangers in step 3 above. SEE FIGURE 14. With a mallet, tap items “D” on the frame where you just removed the stock spring pivot hangers. The tab on the under side (for the locking bolt item “E”) faces forward. On the passenger side frame, have a friend hold the dumb end of a tape measure up to the center of item “J” that goes through the center of items “C” at the new M.O.R.E.™ pivot bracket. SEE FIGURE 15.
PAGE 6
Figure 1 Figure 2 Figure 3 OEM Item J Figure 4 Figure 7 Figure 5 Figure 8 8795-2 PAGE 6 Figure 6 Figure 9
PAGE 7
Figure 11 Figure 12A Figure 10 Figure 12B Figure 13A Figure 13C 8795-2 PAGE 7 Figure 13B
PAGE 8
Figure 14 Drivers Side-Forward Figure 16 Figure 15 Inside Frame Rail Drivers Side-Forward Figure 18 Figure 17 8795-2 PAGE 8
PAGE 9
Figure 19 Figure 22 Figure 20 Figure 23 Figure 25 8795-2 PAGE 9 Figure 21 Figure 24