Instruction manual

10
ENGLISH
EN
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The
washer/washers must not be forced in, as there
must be a little axial play.
4. Pull out the cotter pin and disMantle the
steering wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
6. Install the steering column jacket on the
steering column and secure by knocking in the
cotter pin fully. Use a counterhold.
3.6 TOWING HITCH
Screw the towing hitch (5:A) into the two holes on
the underside of the rear axle using screws 5:B).
Tighten the screws properly.
Tightening torque: 22 Nm.
3.7 DECK MOUNT
This only describes installation on the right-hand
axle. The same procedure must be carried out on
the left-hand axle.
1. Remove the circlip (20:M) and the outer washer
(20:N).
2. Install the deck mount (20:O).
The washer (20:N) with an inner lug
must always be placed against the
circlip. Otherwise there is a risk of the
circlip coming loose.
3. Install the outer washer (20:N) and the circlip
(20:M).
4. Lubricate the deck mount’s lubricating cup
using a grease gun until grease penetrates along
side the axle.
The screws (1:P) and the nuts (1:Q) must be used
to install the work tool in the deck arms (20:O).
3.8 TYRE PRESSURE
Check the air pressure in the tyres. Correct air
pressure:
Front: 0.4 bar (6 psi)
Rear: 1.2 bar (17 psi)
3.9 ACCESSORIES
For the installation of accessories, see separate
installation guide supplied with each accessory.
Note: The cutting deck is regarded as an accessory
here.
4 DESCRIPTION
4.1 DRIVE
The machine has front-wheel drive.
Front-mounted implements are powered via drive
belts.
4.2 STEERING
The machine has rear-wheel steering. The rear-
wheel steering means that the machine can easily
turn around trees and other obstacles. Steering is
controlled via a wire or wire-chain.
4.3 SAFETY SYSTEM
The machine is equipped with an electrical safety
system. The safety system interrupts certain
activities that can entail a danger of incorrect
manoeuvres.
For example, the engine can only be started if the
clutch-parking brake pedal is depressed.
The operation of the safety system must
always be checked every time before
use.
4.4 CONTROLS
4.4.1 Implement lifter (6:P)
To switch between working position and transport
position:
1. Depress the pedal fully.
2. Release the pedal slowly.
4.4.2 Service break/clutch(6:M) (2125M)
A pedal that combines both service brake and
clutch. There are 3 positions:
1. Pedal released – forward
drive engaged. The machine will
move if a gear is engaged.
Service brake not activated.
2. Pedal depressed halfway – forward drive
disengaged, gear shifting can be performed.
Service brake not activated.
3. Pedal fully depressed – forward drive
disengaged. Service brake fully activated.
NOTE! You must never regulate the operating
speed by slipping the clutch. Use a suitable gear
instead, so that the right speed is obtained.
4.4.3 Clutch-parking brake (6:M)
(2135H)
Never press the pedal while driving.
There is a risk of overheating in the
power transmission.
The pedal (6:M) has the
following three positions:
1. Pedal released – The clutch
is not activated. The parking
brake is not activated.
2. Pedal depressed halfway – forward drive
disengaged. The parking brake is not activated.
3. Pedal fully depressed – forward drive
disengaged. The parking brake is fully activated
but not locked. This position is also used as
emergency brake.