TABLE OF CONTENTS 1. CONNECTION OF POWER WIRES FOR PERMANENT WIRING 2 2. DUCT WORK PROCEDURE . Unit Installed on the Floor 3. USE OF UNIT AS PORTABLE TYPE Installation of Casters 4. OUTDOOR INSTALLATION OF THE UNIT Installation of the Remote Controller {Option} .. 5. OVERALL DIMENSIONS HUB iiieiiieniriiniiicnoinonronisronssnons CAUTION Do not install the unit in following places. «Where the ambient temperature is always below 25°C (77°F) or above 45°C (113°F) 8t 50% relative humidity.
CONNECTION OF POWER WIRES FOR PERMANENT WIRING Power Supply POWER sounds‘ ® The power supply of Sr or Com AC460V, 34. 60Hz sl AC 460V £ 10%, three short-CIRCUN phase and 60 Hz. Do not connect the unit to any other power 1 PROTECTIVE supply. : BREAKER. { ® Single outlet circuit only. : GREEN : COLORED WIRE ® As shown at right, be sure to : provide a fuse of 20A capacity ! GROUNDING max. And short circuit and :TERMINAL ground-fault protective breaker s for the power supply.
Pass the power wire through the conduit hole in the side panel (left-hand side toward you) and lead the ends of power wires to the inside of control box. Attach the conduit tubing to the conduit hole. Trade size of conduit inch. is 172 MACHINE SCREW CONTROL BOX CONDUIT HOLE REMOVAL OF CONTROL BOX COVER Crimp the terminal eyelets, which are provided in the package, to the power wires and secretly tighten them to the R, S, T and Grounding terminals of terminal block.
DUCT WORK PROCEDURE For the Scooter son, it is necessary to perform duct work according to the requirement of user. The work procedure is described below. CAUTION The Sportscast son should always be placed on the floor. It should never be hung from the ceiling. ‘nit Installed on the Floor Example 1 CHAMBER Supplied Parts {Option) Du Ct Part Name Part No. 1150 MM diam.) Chamber 481769-0081 {3 ports} ; TRIM Duct 481744-0030 / Trim 481851-0210 Note: A maximum length of duct is 2 m.
3. USE OF UNIT AS PORTABLE TYPE The Schoolroom sou can be used as a portable spot cooling system by attaching the casters. » Note: 1. Do not use the unit in portable configuration outdoors. 2. Use the duct specified in example of the duct work procedure. Installation of Casters Note: Duct length 1 m each. (Caster Kit Part No. 484708-0020: Option) 1)} Suspend the unit with & hoist. 2} Remove 4 legs at the bot torn of \l the unit. LEG REMOVING LEGS 3) Install 4 casters using 16 bolts that were removed.
OUTDOOR INSTALLATION OF THE UNIT The SrotrCooLsonu can be installed outdoors as illustrated below, and feeding the cooling 2ir duct to indoor. Install the unit by following the procedure given below. OUTDOOR INSTALLATION OF THE UNIT DUCT SUSPENSION WIRE T SEAL MERE TO PREVENT ENTRY OF RAIN WATER DUCT: INSTALLED AS PER BUILDING | DUCT WORK PROCEDURE 2 WALL POWER BOX o BOX 7 OR & REMOTE CONTROL WIRES RUNNING HIGHER /mutinous CONDUIT TUBING POWER WIRES RUNNING V THROUGH CONDUIT TUBING BLOCK Note: 1.
Installation of the Remote Controller (O piton) This controller should be installed only indoor in accordance with all local codes. In the absence of local codes, install in accordance with the National Electric Code (NECK. 1) Remote control switch kit (Part number 484500-0430). The remote control switch kit contains the following parts, REMOTE CONTROL BOX COVER \ TERMINAL EYELET {13} TERMINAL EYELET {FOR GROUNDING} {3} Assemble these pars to install the controller by following the procedure given below.
4) Use a UL Listed metallic cable conductor appropriate for use and fit it into the 22.2mm hole in the remote control box. Pass six BAWL wires and one green insulated grounding wire through the conduit tubing and crimp the attached terminal eyelets to the ends of wires to connect them to terminals. Replace the remote control box cover and secure it with four machine screws.
5) Wiring the Cesspool sumo control box Lead in the wires running through conduit tubing from the remote control switch to the conduit into the unit's control box through the grommet located on right side panel of the box. TERMINAL BLOCK TO GROUNDING TERMINAL. Using the furnished terminal eyelets, connect six wires to the correct terminals, matching waterfront PANEL final numbers with those of SWITCH KNOB the remote control box. (Ensure . . COVER the correct pair of the terminal number.
