Rg2i Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Serial Media Converters Chassis Media Converters TRC-190-AC TRC-190-DC TCF-142-M-SC-RM TCF-142-M-ST-RM – – – – – – SC or ST 50/125, 62.5/125, or 100/140 μm 5 km 850 nm > -5 dBm -20 dBm – Point-to-Point Transmission: Half-duplex or full-duplex – – – – – – – DB9 TxD, RxD, GND TxD+, TxD-, RxD+, RxD-, GND TxD+, TxD-, RxD+, RxD-, GND Data+, Data-, GND 50 bps to 921.6 Kbps 15 KV SECC (1.2 mm) 440 x 260 x 77 mm 5.2 kg (11.
Device Connectivity Serial-to-Fiber Media Converters ICF-1150-M-SC/ST ICF-1150-M-SC/ST-T ICF-1150I-M-SC/ST ICF-1150I-M-SC/ST-T ICF-1150-S-SC/ST ICF-1150-S-SC/ST-T ICF-1150I-S-SC/ST ICF-1150I-S-SC/ST-T TCF-142-M-SC/ST TCF-142-M-SC/ST-T TCF-142-S-SC/ST TCF-142-S-SC/ST-T TCF-90-M/S Optical Fiber Side Fiber Connector Cables Requirements Transmission Distance Wavelength Tx Output Rx Sensitivity ST Half-duplex or full-duplex – Half-duplex, fiber ring – 13 RS-232 Side Connector DB9 female Signals
Serial Media Converters Serial Converters and Repeaters TCC-100 TCC-100-T TCC-100I TCC-100I-T TCC-80 TCC-80I TCC-120 TCC-120I TCC-82 DB9 male/female TxD, RxD, RTS, CTS, GND (Loop-back wiring: DTR to DSR and DCD) RS-232 Side 13 Serial Media Converters > Product Selection Guide Connector DB9 female DB9 female – – Signals TxD, RxD, RTS, CTS, GND (Loop-back wiring: DTR to DSR and DCD) TxD, RxD, GND (Loop-back wiring: RTS to CTS, DTR to DSR and DCD) – – Terminal Block (interface selected by
Device Connectivity CAN-to-Fiber, PROFIBUS-to-Fiber Converters ICF-1170I-M-ST ICF-1170I-M-ST-T ICF-1180I-M-ST/ST-T ICF-1180I-S-ST/ST-T Optical Fiber Side Fiber Connector Cables Requirements ST Multi-mode: 50/125, 62.
Serial Media Converters Rg2i Groupe TRC-190 Series 2AR Interfaces pour l’informatique industrielle www.rg2i.
Device Connectivity Dimensions Unit: mm (inch) TRC-190-ACx2 TRC-190-DCx2 TRC-190-DCx1 13 440 (17.32) 484 (19.06) 465.6 (18.33) 33 (1.30) 260 (10.24) 33 88 (3.
Serial Media Converters Rg2i Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Device Connectivity Dimensions Unit: mm (inch) TCF-142-M/S-ST-RM Series TCF-142-M/S-SC-RM Series 86.8 (3.42) 86.8 (3.42) 124.3 (4.9) 129.3 (5.09) 136.46 (5.38) 124.3 (4.9) 13 129.3 (5.09) Serial Media Converters > TCF-142-RM Series 21 (0.
Serial Media Converters Rg2i Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.com ICF-1150 Series Industrial serial-to-fiber converters ››3-way communication: RS-232, fiber, and RS-422/485 ››Rotary switch to change the pull high/low resistor value ››Extend RS-232/422/485 transmission up to: • 40 km with single-mode • 5 km with multi-mode 3-way Galvanic Isolation (for “I” model only) -40 to 85°C wide temperature models available Class I, Div.
Device Connectivity Physical Characteristics Standards and Certifications Housing: Metal Dimensions: 30.3 x 70 x 115 mm (1.19 x 2.76 x 4.
Serial Media Converters Ordering Information Available Models 13 Serial Media Converters > ICF-1150 Series 13-12 ICF-1150-M-SC: Industrial RS-232/422/485 to multimode fiber converter, SC connector, 0 to 60°C operating temperature ICF-1150-M-ST: Industrial RS-232/422/485 to multimode fiber converter, ST connector, 0 to 60°C operating temperature ICF-1150-S-SC: Industrial RS-232/422/485 to single mode fiber converter, SC connector, 0 to 60°C operating temperature ICF-1150-S-ST: Industrial RS-232/422/485 to
Device Connectivity Rg2i Groupe TCF-142 Series 2AR Interfaces pour l’informatique industrielle www.rg2i.com RS-232/422/485 to optical fiber media converters ››“Ring” and “Point- to-Point” transmission ››Extends RS-232/422/485 transmission up to: • 40 km with single-mode—TCF-142-S • 5 km with multi-mode—TCF-142-M Decreases signal interference Protects against electrical interference and chemical corrosion Supports baudrates up to 921.
Serial Media Converters Specifications Optical Fiber Side 13 Environmental Limits Serial Media Converters > TCF-142 Series Fiber Connector: SC or ST Cable Requirements: Single-mode: 8.3/125, 8.7/125, 9/125, or 10/125 μm Multi-mode: 50/125, 62.
Device Connectivity Dimensions Unit: mm (inch) TCF-142-M/S-SC 22.0 (0.87) Ø6 (0.24) 25 (0.98) 12.5 (0.49) 100.4 (3.95) Ø4 (0.16) Ø7 (0.28) 22.0 (0.87) 21.3 (0.8) 67 (2.64) 67 (2.64) 78 (3.07) 90.2 (3.
Serial Media Converters Rg2i Groupe TCF-90 Series 2AR Interfaces pour l’informatique industrielle www.rg2i.
Device Connectivity Specifications Optical Fiber Side Environmental Limits Fiber Connector: ST Cable Requirements: Single-mode: 8.3/125, 8.7/125, 9/125, or 10/125 μm Multi-mode: 50/125, 62.
Serial Media Converters Rg2i Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Device Connectivity Rg2i Groupe TCC-80/80I Series 2AR Interfaces pour l’informatique industrielle www.rg2i.com Port-powered RS-232 to RS-422/485 converters with optional 2.5 KV isolation TCC-80-DB9 TCC-80 TCC-80I-DB9 TCC-80I ››External power source supported but not required ››Compact size ››Converts RS-422, and both 2-wire and 4-wire RS-485 ››RS-485 automatic data direction control ››Automatic baudrate detection ››15 KV serial ESD protection ››Built-in 120-ohm termination resistors ››2.
Serial Media Converters Port Power Dissipation When installing a TCC-80 or TCC-80I converter, it is important to pay attention to power consumption, RS-232 cable length, and RS422/485 transmission distance. In general, the TCC-80 and TCC-80I obtain 50 mW of power from the power source. Standard PC COM ports can provide 70 to 90 mW of power if the TxD, RTS, and DTR lines are connected.
Device Connectivity Dimensions Unit: mm (inch) TCC-80 DB9 female connector DIP Switch Settings ON 1 5 4 3 2 1 2 3 DIP Switch Settings 9 8 7 6 PIN RS-232 1 DCD TCC-80I 2 TxD 3 RxD 4 DSR 5 GND 6 DTR 7 CTS 8 RTS RS-422 with Terminator SW1 SW2 OFF OFF ON RS-422 SW1 SW2 SW3 OFF OFF OFF 4-wire RS-485 with Terminator SW1 SW2 SW3 ON OFF ON 4-wire RS-485 SW1 SW2 SW3 ON OFF OFF 2-wire RS-485 with Terminator SW1 SW2 SW3 ON ON ON 2-wire RS-485 SW1 SW2 SW3
Serial Media Converters Rg2i Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Device Connectivity Rg2i TCC-82 Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.com Port-powered RS-232 4-channel isolator ››4 channels of 4 KV RMS isolation for 1 minute ››External power source supported but not required ››15 KV serial ESD protection ››Automatic baudrate detection ››Compact size 13 The TCC-82 provides full electrical isolation for bi-directional serial communication between two RS-232 devices in a compact, industrialgrade package.
Serial Media Converters Specifications Serial Communication Input Voltage: 5 to 12 VDC Power Consumption: 20 mA @ 5 V Connectors: DB9 male and DB9 female Baudrate: 50 bps to 921.
Device Connectivity Introduction to CAN-to-Fiber Media Converters Introduction to CAN CAN is a serial communications bus defined by the International Standardization Organization (ISO). The CAN serial bus was introduced in 1986 as the “Automotive Serial Controller Area Network,” a multimaster message broadcast system that specifies a maximum signaling rate of 1 Mbps.
Serial Media Converters Special Features Fiber Test Mode The ICF-1170I supports a special feature called Fiber Test Mode, which is easily activated with a DIP switch on the ICF-1170I’s outer panel. Fiber Test Mode can be used to test the fiber cable between two ICF1170I units, and provides a simple way to determine if the fiber cable is transmitting data correctly.
Device Connectivity Rg2i ICF-1170I Series Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Serial Media Converters Standards and Certifications Safety: UL 508, EN 60950-1 EMC: CE, FCC EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A EMS: EN 61000-4-2 (ESD) Level 4, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 4, EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 (PFMF) Level 3 Freefall: IEC 60068-2-32 Green Product: RoHS, CRoHS, WEEE Time: 792,085 hrs Database: Telcordia (Bellcore), GB Warranty Warranty Period: 5 years Details: See www.moxa.
Device Connectivity Rg2i ICF-1180I Series Groupe 2AR Interfaces pour l’informatique industrielle www.rg2i.
Serial Media Converters Specifications Technology Physical Characteristics Housing: Metal Mounting: Din-rail Dimensions: 30.3 x 70 x 115 mm (1.19 x 2.76 x 4.