Datasheet

ManualsBrandsMoxa ManualsAutomationIndustrial Wireless Access Point 300Mbps IP30

www.moxa.com

AWK-1131A Series

Entry-level industrial IEEE 802.11a/b/g/n wireless AP/client

Features and Benefits

• IEEE 802.11a/b/g/n AP/client support

• Millisecond-level Client-based Turbo Roaming

• Integrated antenna and power isolation

• 5 GHz DFS channel support

Certifications

Introduction

The AWK-1131A industrial wireless AP/client meets the growing need for faster data transmission speeds by supporting IEEE 802.11n technology

with a net data rate of up to 300 Mbps. The AWK-1131A is compliant with industrial standards and approvals covering operating temperature,

power input voltage, surge, ESD, and vibration. The two redundant DC power inputs increase the reliability of the power supply. The AWK-1131A

can operate on either the 2.4 or 5 GHz bands and is backwards-compatible with existing 802.11a/b/g deployments to future-proof your wireless

investments.

Improved Higher Data Rate and Channel Capacity

• High-speed wireless connectivity with up to 300 Mbps data rate

• MIMO technology to improve the capability of transmitting and receiving multiple data streams

• Increased channel width with channel bonding technology

• Supports flexible channel selection to build up wireless communication system with DFS

Specifications for Industrial-grade Applications

• Redundant DC power inputs

• Integrated isolation design with enhanced protection against environmental interference

• Compact aluminum housing, IP30-rated

Specifications

WLAN Interface

WLAN Standards 802.11a/b/g/n

802.11i Wireless Security

Modulation Type DSSS

OFDM

MIMO-OFDM

Frequency Band for US (20 MHz operating channels) 2.412 to 2.462 GHz (11 channels)

5.180 to 5.240 GHz (4 channels)

5.260 to 5.320 GHz (4 channels)

5.500 to 5.700 GHz (11 channels)

5.745 to 5.825 GHz (5 channels)

Frequency Band for EU (20 MHz operating channels) 2.412 to 2.472 GHz (13 channels)

5.180 to 5.240 GHz (4 channels)

1. The Turbo Roaming recovery time indicated herein is an average of test results documented, in optimized conditions, across APs configured with interference-free

20-MHz RF channels, WPA2-PSK security, and default Turbo Roaming parameters. The clients are configured with 3-channel roaming at 100 Kbps traffic load.

Other conditions may also impact roaming performance. For more information about Turbo Roaming parameter settings, refer to the product manual.

2. DFS (Dynamic Frequency Selection) channel support: In AP mode, when a radar signal is detected, the device will automatically switch to another channel.

However, according to regulations, after switching channels, a 60-second availability check period is required before starting the service.

Summary of content (6 pages)

PAGE 1
AWK-1131A Series Entry-level industrial IEEE 802.11a/b/g/n wireless AP/client Features and Benefits • IEEE 802.11a/b/g/n AP/client support • Millisecond-level Client-based Turbo Roaming1 • Integrated antenna and power isolation • 5 GHz DFS channel support Certifications Introduction The AWK-1131A industrial wireless AP/client meets the growing need for faster data transmission speeds by supporting IEEE 802.11n technology with a net data rate of up to 300 Mbps.
PAGE 2
5.260 to 5.320 GHz (4 channels)3 5.500 to 5.700 GHz (11 channels)3 Frequency Band for JP (20 MHz operating channels) 2.412 to 2.484 GHz (14 channels) 5.180 to 5.240 GHz (4 channels) 5.260 to 5.320 GHz (4 channels)3 5.500 to 5.700 GHz (11 channels)3 Wireless Security WEP encryption (64-bit and 128-bit) WPA/WPA2-Enterprise (IEEE 802.1X/RADIUS, TKIP, AES) WPA/WPA2-Personal Transmission Rate 802.11b: 1 to 11 Mbps 802.11a/g: 6 to 54 Mbps 802.11n: 6.5 to 300 Mbps Transmitter Power for 802.11a 23±1.
PAGE 3
Typ. -63 dBm @ MCS7 40 MHz Typ. -68 dBm @ MCS15 40 MHz Note5 Receiver Sensitivity for 802.11b (measured at 2.437 GHz) Typ. -93 dBm @ 1 Mbps Typ. -93 dBm @ 2 Mbps Typ. -93 dBm @ 5.5 Mbps Typ. -88 dBm @ 11 Mbps Receiver Sensitivity for 802.11g (measured at 2.437 GHz) Typ. -88 dBm @ 6 Mbps Typ. -86 dBm @ 9 Mbps Typ. -85 dBm @ 12 Mbps Typ. -85 dBm @ 18 Mbps Typ. -85 dBm @ 24 Mbps Typ. -82 dBm @ 36 Mbps Typ. -78 dBm @ 48 Mbps Typ. -74 dBm @ 54 Mbps Receiver Sensitivity for 802.11n (2.4 GHz; measured at 2.
PAGE 4
Dimensions 58 x 115 x 70 mm (2.29 x 4.53 x 2.76 in) Weight 307 g (0.68 lb) Installation DIN-rail mounting, Wall mounting (with optional kit) Power Parameters Input Current 0.56 A @ 12 VDC, 0.14 A @ 48 VDC Input Voltage 12 to 48 VDC Power Connector 1 removable 4-contact terminal block(s) Power Consumption 6.96 W (max.) Reverse Polarity Protection Supported Environmental Limits Operating Temperature Standard Models: 0 to 60°C (32 to 140°F) Wide Temp.
PAGE 5
Dimensions Ordering Information Model Name Band Standards Operating Temp. AWK-1131A-EU EU 802.11a/b/g/n 0 to 60°C AWK-1131A-EU-T EU 802.11a/b/g/n -40 to 75°C AWK-1131A-JP JP 802.11a/b/g/n 0 to 60°C AWK-1131A-JP-T JP 802.11a/b/g/n -40 to 75°C AWK-1131A-US US 802.11a/b/g/n 0 to 60°C AWK-1131A-US-T US 802.11a/b/g/n -40 to 75°C Accessories (sold separately) Antennas ANT-WDB-ANF-0407 2.4/5 GHz, omni-directional antenna, 4/7 dBi, N-type (female) ANT-WDB-ANF-0609 2.
PAGE 6
ANT-WSB-PNF-12 2.4 GHz, directional panel antenna, 12dBi, N-type (female) ANT-WSB-PNF-18 2.4 GHz, directional panel antenna, 18 dBi, N-type (female) ANT-WSB-AHRM-05-1.5m 2.4 GHz, omni-directional/dipole antenna, 5 dBi, RP-SMA (male), 1.5 m cable Wireless Antenna Cables A-CRF-RFRM-R4-150 RF magnetic stand, RP-SMA (male) to RP-SMA (female), RG-174/U cable, 1.