EDS-2008-EL/ELP Series Quick Installation Guide Moxa EtherDevice Switch Version 1.0, October 2019 Technical Support Contact Information www.moxa.
Overview The EDS-2008-EL/ELP Series has an 8-port combination to simplify network expansion. There are two housing types available for the user to select depending on the requirements of their application. The ELP has a plastic housing and the EL has a metal housing. The compact switches provide a cost-effective solution for your industrial Ethernet connection requirements. The EDS-2008-EL/ELP Series provides 12/24/48 VDC (9.
Features High Performance Network Switching Technology • • • • 10/100BaseT(X) auto-negotiation speed, full/half duplex mode, auto MDI/MDI-X connection, and 100BaseFX for fiber port models. IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X). IEEE 802.1p for Quality of Service (QoS) traffic prioritized function. Store-and-forward switching process type.
Panel Layout of EDS-2008-EL/EDS-2008-ELP 1. 2. 3. 4. 5. 6. 7. 8.
Panel Layout of EDS-2008-EL-M-ST/ EDS-2008-EL-M-SC 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Mounting Dimensions EDS-2008-EL Series EDS-2008-ELP Series -6-
EDS-2008-EL-M-ST Series EDS-2008-EL-M-SC Series -7-
DIN-rail Mounting When shipped, the DIN-rail mounting kit is fixed to the back panel of the EDS. Mount the EDS on the corrosion-free mounting rail that adheres to the EN 60715 standard. Suggested Installation Method STEP 1: Insert the upper lip of the DINrail kit into the mounting rail. STEP 2: Press the device towards the mounting rail until it snaps into place. Alternatively, you can use a screwdriver to attach to the bottom of the DIN-rail kit and pull down.
Wall Mounting (optional) For some applications, you will find it convenient to mount EDS on the wall, as illustrated below. There are two options for installation: The first option is to hook the EDS DIN-rail latch on the opening of the wall mount kit (see picture above) and then mount the wall-mount kit on the wall with screws. (The other option is to perform these two steps in the other order.) The heads of the screws should be less than 6.0 mm in diameter, and the shafts should be less than 3.
Wiring Requirements WARNING Do not disconnect modules or wires unless the power supply has been switched off or the area is known to be nonhazardous. The devices may only be connected to the supply voltage shown on the type plate. The devices are designed for operation with a Safety Extra-Low Voltage. Thus, they may only be connected to the supply voltage connections and to the signal contact with the Safety Extra-Low Voltages (SELV) in compliance with IEC950/ EN60950/ VDE0805.
ATTENTION This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel. Wiring the Power Input The top two contacts and the bottom two contacts of the 2 or 3 contact terminal block connector on the EDS’s top panel are used for the EDS’s two DC inputs. Top and front views of one of the terminal block connectors are shown here. STEP 1: Insert the negative/positive DC wires into the V-/V+ terminals.
10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on the EDS’s front panel are used to connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show cable wiring diagrams for straight-through and cross-over Ethernet cables.
SC-port Pinouts SC-port to SC-port Cable Wiring ST-port Pinouts ST-port to ST-port Cable Wiring ATTENTION This is a Class 1 Laser/LED product. To prevent damage to your eyes, do not stare directly into the laser beam. DIP Switch Settings DIP Switch Quality of Service (QoS) Setting ON Description Enable the Quality of Service to handle packet priorities in four WRR queues.
LED Indicators The front panel of the Moxa EtherDevice Switch contains several LED indicators. The function of each LED is described in the table below. LED PWR (P) Color State Description Power is being supplied to power input PWR. Power is not being supplied to power input Off PWR. When the port is active and links on 100 On Mbps. When the port’s data is being transmitted Blinking at 100 Mbps. Off When the port is inactive or link down. When the port is active and links on 10 On Mbps.
Switching and Address Learning The Moxa EDS has an address table that can hold up to 8,000 node addresses, which makes it suitable for use with large networks. The address tables are self-learning, so that as nodes are added or removed, or moved from one segment to another, EDS automatically keeps up with new node locations. An address-aging algorithm causes the least-used addresses to be deleted in favor of newer, more frequently used addresses.
Reverse Polarity Protection Mechanical Casing Present IP40 protection, metal housing for EL Series; plastic housing for ELP Series Dimensions EDS-2008-EL/ELP: (W x H x D) 36 x 81 x 65 mm (1.4 x 3.19 x 2.56 in) EDS-2008-EL-M-ST: 36 x 81 x 70.9 mm (1.4 x 3.19 x 2.79 in) EDS-2008-EL-M-SC: 36 x 81 x 67.9 mm (1.4 x 3.19 x 2.67 in) Weight EDS-2008-ELP: 90 g (0.2 lb) EDS-2008-EL/EDS-2008-EL-M-SC/EDS-2008-EL-MST: 163 g (0.
