EDS-405A/408A Series Quick Installation Guide Moxa EtherDevice™ Switch Edition 12.1, September 2018 Technical Support Contact Information www.moxa.
Overview The Moxa EtherDevice™ EDS-405A/408A series, which includes both 5 and 8-port smart Ethernet switches, is a cost-effective solution for your Ethernet connections. In addition, the built-in smart alarm function helps system maintainers monitor the health of your Ethernet network. Package Checklist The Moxa EDS-405A/408A switches are shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance.
EDS-405A/408A Panel Layout (standard) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
EDS-405A/408A-MM (SC-type) Panel Layout NOTE: The appearance of the EDS-405A-SS-SC is identical to that of the EDS-405A-MM-SC. The appearance of the EDS-408A-SS-SC is identical to that of the EDS-408A-MM-SC. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
EDS-405A/408A-MM (ST-type) Panel Layout 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
EDS-408A-3M Panel Layout (SC/ST-type) NOTE: The appearance of the EDS-408A-3S-SC, EDS-408A-1M2S-SC, and EDS-408A-2M1S-SC are identical to that of the EDS-408A-3M-SC. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Mounting Dimensions Unit = mm (inch) DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the EDS-405A/408A when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the following figures.
STEP 1: Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2: The DIN-Rail attachment unit will snap into place as shown. To remove the Moxa EtherDevice switch from the DIN-Rail, simply reverse Steps 1 and 2. NOTE In order to ensure reliable operations, please make sure the operating temp. of the environment does not exceed the spec.
ATEX/IECEx Information 1. 2. 3. 4. 5. 6. Certificate number: ATEX: DEMKO 18 ATEX 1978X IECEx: IECEx UL 18.
Wiring Requirements WARNING Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa EtherDevice Switch. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment.
FAULT: The two middle contacts of the 6-contact terminal block connector are used to detect both power faults and port faults. The two wires attached to the fault contacts form an open circuit when: A relay warning event is triggered. OR The EDS-405A/408A is the Master of this Turbo Ring, and the Turbo Ring is broken. OR There is a start-up failure. If none of these three conditions is satisfied, the fault circuit will remain closed.
10/100Base T(x) RJ45 Pinouts MDI Port Pinouts Pin 1 2 3 6 Signal Tx+ TxRx+ Rx- MDI-X Port Pinouts Pin 1 2 3 6 8-pin RJ45 Signal Rx+ RxTx+ Tx- RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring 100BaseFX Ethernet Port Connection The concept behind the SC/ST port and cable is quite straightforward. Suppose you are connecting devices I and II; contrary to electrical signals, optical signals do not require a circuit in order to transmit data.
SC-Port Pinouts SC-Port to SC-Port Cable Wiring ST-Port Pinouts ST-Port to ST-Port Cable Wiring ATTENTION This is a Class 1 Laser/LED product. To avoid causing serious damage to your eyes, do not stare directly into the laser beam. Redundant Power Inputs Both power inputs can be connected simultaneously to live DC power sources. If one power source fails, the other live source acts as a backup, and automatically supplies the EDS-405A/408A with power.
There are 4 Hardware DIP Switches for Turbo Ring on the top panel of the EDS-405A/408A that can be used to set up the Turbo Ring easily within seconds. If you do not want to use a hardware DIP switch to set up Turbo Ring, you can use a web browser, Telnet, or console to disable this function. NOTE Refer to the Turbo Ring DIP Switch section and Using Communication Redundancy section in the user’s manual for detailed information about the settings and usage of Turbo Ring and Turbo Ring V2.
LED Indicators There are several LEDs on the EDS’s front panel. The function of each LED is described in the following table. LED Color State On PWR1 AMBER Off On PWR2 AMBER Off On FAULT RED Off On MSTR/HEAD GREEN Blinking Off On CPLR/TAIL GREEN Blinking Off 10M (TP) GREEN 100M (TP) GREEN 100M (FX) GREEN On Blinking Off On Blinking Off On Blinking Off Description Power is being supplied to power input PWR1. Power is not being supplied to power input PWR1.
Auto MDI/MDI-X Connection The Auto MDI/MDI-X function allows users to connect the EDS-405A/408A’s 10/100BaseTX ports to any kind of Ethernet device, without needing to pay attention to the type of Ethernet cable being used for the connection. This means that you can use either a straight-through cable or cross-over cable to connect the EDS-405A/408A to Ethernet devices.
Power Input Voltage Input Current Inrush current • EDS-405A/408A Series: 12/24/48 VDC, redundant inputs • EDS-408A-3S-SC-48: ±24/±48 VDC (-60 to -19 VDC or 19 to 60 VDC), redundant inputs (The mixing of power polarity system is prohibited.) • EDS-405A Series: 0.594 A/0.286 A/0.154 A @ 12/24/48 V • EDS-408A Series (copper and 2 fiber models): 0.61 A/0.3 A/0.16 A @ 12/24/48 V • EDS-408A Series (3 fiber models): 0.73 A/0.35 A/0.18 A @ 12/24/48 V • EDS-405A Series: Max. 2.08 A @ 24 VDC (0.
EMS Shock Freefall Vibration WARRANTY EN 61000-4-2 (ESD), Level 3 EN 61000-4-3 (RS), Level 3 EN 61000-4-4 (EFT), Level 3 EN 61000-4-5 (Surge), Level 3 EN 61000-4-6 (CS), Level 3 IEC 60068-2-27 IEC 60068-2-31 IEC 60068-2-6 5 years Manufacturer Address: FI.4, No.135, Lane 235, Baoqiao Rd. Xindian Dist., New Taipei City, Taiwan WARNING This equipment is intended to be used in a Restricted Access Location. WARNING: Hot Surface! Before touching it, special attention or protection is required.
