EDS-G205-1GTXSFP Quick Installation Guide Moxa EtherDevice Switch Edition 3.0, February 2017 Technical Support Contact Information www.moxa.
Overview The EDS-G205-1GTXSFP switches are equipped with 5 Gigabit Ethernet ports (4 10/100/1000BaseT(X) ports and 1 combo 10/100/1000BaseT(X) or 100/1000BaseSFP port), making them ideal, economical solutions for demanding, high bandwidth Gigabit Ethernet applications. In addition, the built-in relay warning function alerts system administrators when power failures or port breaks occur, and the add-on 4-pin DIP switches can be used to configure broadcast storm protection, jumbo frame rate, IEEE 802.
Panel Layout of the EDS-G205-1GTXSFP 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Mounting Dimensions, unit = mm (inch) DIN Rail Mounting The aluminum DIN rail attachment plate should already be fixed to the back panel of the switch when you take it out of the box. If you need to reattach the DIN rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below.
STEP 1: Insert the top of the DIN rail into the slot just below the stiff metal spring. STEP 2: The DIN rail attachment unit will snap into place as shown below. To remove the DIN rail from the switch, simply reverse Steps 1 and 2. Wall Mounting (optional) For some applications, you will find it convenient to mount the switch on the wall, as illustrated below. STEP 1: Remove the aluminum DIN rail attachment plate from the switch’s rear panel, and then attach the wall mount plates, as shown in the figure.
Wiring Requirements WARNING Safety First! Turn the power off before disconnecting modules or wires. The proper power supply voltage is listed on the product label. Check the voltage of your power source to make sure you are using the correct voltage. Do NOT use a voltage greater than what is specified on the product label. These devices must be supplied by an AELV source as defined in the Low Voltage Directive 2006/95/EC and 2004/108/EC.
Wiring the Alarm Contact The alarm contact consists of the two middle contacts of the terminal block on the switch’s top panel. You may refer to the next section for detailed instructions on how to connect the wires to the terminal block connector, and how to attach the terminal block connector to the terminal block receptor. In this section, we explain the meaning of the two contacts used to connect the alarm contact.
Communication Connections EDS-G205-1GTXSFP switches have 2 types of communication port: • • 4 10/100/1000BaseT(X) Ethernet ports 1 combination 10/100/1000T(X) or 100/1000BaseSFP port 10/100/1000BaseT(X) Ethernet Port Connection The 10/100/1000BaseT(X) ports located on switch’s front panel are used to connect to Ethernet-enabled devices.
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring 100/1000BaseSFP (mini-GBIC) Fiber Port One of the Gigabit Ethernet ports on the EDS-G205-1GTXSFP is an SFP slot, which requires 100M or 1G mini-GBIC fiber transceivers to work properly. Moxa provides complete transceiver models for various distance requirements. The concept behind the LC port and cable is straightforward. Suppose you are connecting devices I and II.
Alarm Contact The EDS-G205-1GTXSFP has one alarm contact located on the top panel. For detailed instructions on how to connect the alarm contact power wires to the two middle contacts of the 6-contact terminal block connector, see the Wiring the Alarm Contact section on page 7. A typical scenario would be to connect the Fault circuit to a warning light located in the control room. The light can be set up to switch on when a fault is detected.
LED Indicators The front panel of the EDS-G205-1GTXSFP switch contains several LED indicators. The function of each LED is described in the table below. LED Color State Description Power is being supplied to power input PWR1 Power is not being supplied to power input Off PWR1 Power is being supplied to power input On PWR2 Power is not being supplied to power input Off PWR2 When the corresponding PORT alarm is On enabled, and the port’s link is inactive.
Auto-negotiation takes place when an RJ45 cable connection is made, and then each time a LINK is enabled. The switch advertises its capability for using 10 Mbps, 100 Mbps, or 1000 Mbps transmission speeds, with the device at the other end of the cable expected to advertise similarly. Depending on what type of device is connected, this will result in agreement to operate at a speed of 10 Mbps, 100 Mbps, or 1000 Mbps.
Power Requirements Input Voltage 12/24/48 VDC, redundant inputs, Class 2 Input Current 0.16 A @ 24 VDC Connection One removable 6-pin terminal block Overload Current Present Protection Reverse Polarity Present Protection Physical Characteristics Housing IP30 protection, metal case Dimensions 29 x 135 x 105 mm (1.14 x 5.31 x 4.
