Datasheet

ManualsBrandsMoxa ManualsComputing & Network ProductsEthernet Peer-to-Peer I/O Unit

www.moxa.com

ioMirror E3200 Series

Ethernet peer-to-peer I/O with 8 digital inputs and 8 digital outputs

Features and Benefits

• Direct input-to-output signal communication over IP

• High-speed peer-to-peer I/O within 20 ms

• One physical alarm port for connectivity status

• Utility for quick and easy web-based settings

• Local alarm channel

• Remote alarm message

• Supports Modbus TCP for remote monitoring

• Optional LCD module for easy configuration

Certifications

Introduction

The ioMirror E3200 Series, which is designed as a cable-replacement solution to connect remote digital input signals to output signals over an IP

network, provides 8 digital input channels, 8 digital output channels, and a 10/100M Ethernet interface. Up to 8 pairs of digital input and output

signals can be exchanged over Ethernet with another ioMirror E3200 Series device, or can be sent to a local PLC or DCS controller. Over a local

area network, the ioMirror can achieve a low signal latency (typically less than 20 ms). With the ioMirror, remote sensors can be connected to local

controllers or display panels over copper, fiber, or wireless Ethernet infrastructures, and signals can be transmitted over virtually unlimited

distances, without noise problems.

Split Sensor Signals to 16 Different Locations

The ioMirror E3200 Series can split one input signal to two digital output channels at two different IP addresses. Eight tank level signals can be

monitored at 16 different display panels, all at the same time.

Local Alarm and Remote Alarm Messages for Monitoring Connectivity

The ioMirror E3200 Series has a 24 VDC alarm output channel that can activate an attached buzzer or LED display when the connection fails. In

addition, both ioMirror modules can send messages to the ioEventLog software, ensuring that at least one of the warning messages will reach the

ioEventLog software.

Specifications

Input/Output Interface

Digital Input Channels 8

Digital Output Channels 8

Alarm Contact Channels 1

Isolation 3k VDC or 2k Vrms

Buttons Reset button

Digital Inputs

Connector Screw-fastened Euroblock terminal

Digital Filtering Time Interval Software configurable

Dry Contact On: short to GND

Off: open

Summary of content (4 pages)

PAGE 1
ioMirror E3200 Series Ethernet peer-to-peer I/O with 8 digital inputs and 8 digital outputs Features and Benefits • Direct input-to-output signal communication over IP • High-speed peer-to-peer I/O within 20 ms • One physical alarm port for connectivity status • Utility for quick and easy web-based settings • Local alarm channel • Remote alarm message • Supports Modbus TCP for remote monitoring • Optional LCD module for easy configuration Certifications Introduction The ioMirror E3200 Series, which is de
PAGE 2
I/O Mode DI Over-Voltage Protection 36 VDC Points per COM 8 channels Sensor Type Dry contact Wet Contact (NPN) Wet Contact (DI to GND) On: 10 to 30 VDC Off: 0 to 3 VDC Digital Outputs Connector Screw-fastened Euroblock terminal Current Rating 200 mA per channel I/O Mode DO I/O Type Sink Over-Current Protection 0.6 A per channel @ 25°C Over-Temperature Shutdown 160°C (min.
PAGE 3
Alarm Contacts I/O Type Sink Current Rating Max. 200 mA per channel Connector Screw-fastened Euroblock terminal Physical Characteristics Housing Plastic Dimensions 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in) Weight 205 g (0.
PAGE 4
Package Contents Device 1 x ioMirror E3200 Series peer-to-peer I/O Installation Kit 1 x terminal block, 3-pin, 3.81 mm 1 x terminal block, 12-pin, 3.81 mm Documentation 1 x quick installation guide Dimensions Ordering Information Model Name ioMirror E3210 Input/Output Interface Operating Temp. 8 x DI, 8 x DO -10 to 60°C © Moxa Inc. All rights reserved. Updated Aug 03, 2020.