NPort IA5000A-I/O Series NPort IAW5000A-I/O Series Quick Installation Guide Edition 2.0, November 2017 Technical Support Contact Information www.moxa.
Overview The NPort IA5000A-I/O and IAW5000A-I/O Series consist of serial device servers with Digital Input/Output (DIO), providing maximum flexibility to integrate serial equipment in the field into Ethernet networks for a variety of industrial data acquisition applications. The DIO on a device can be controlled over TCP/IP, using the Modbus TCP protocol, and it can be configured and secured from a web browser.
NPort IA5000A-I/O Series The mechanical design of the NPort IA5000A-I/O Series is mostly identical; only the number of serial ports and number of DI/DO channels differ. NPort IAW5000A-I/O Series The mechanical design of the NPort IAW5150A and the NPort IAW5250A is mostly identical; only the number of serial ports and number of DI/DO channels differ. LED Indicators Name PWR 1, PWR 2 Ready Color Green Red Function Power is being supplied to power input PWR1, PWR2.
Green WLAN (Only for the NPort IAW5000A-I/O) Signal Strength (3 LEDs only for the NPort IAW5000A-I/O) Ethernet P1, P2 (Serial) DI DO Flashing quickly Steady on Check the relay output first. If the Ready LED is still blinking after resolving the relay output, then there is an IP conflict, or the DHCP or BOOTP server did not respond properly. microSD card failed Power is on, and the NPort is functioning normally.
STEP 1: Insert the top of the DIN rail into the slot. STEP 2: The DIN rail attachment unit will snap into place as shown at right. Wall Mounting (optional) For some applications, it may be more convenient to mount the NPort IA5000A-I/O or IAW5000A-I/O to a wall, as illustrated below. Do not drive the screws in all the way—leave a space of about 2 mm to allow room for sliding the wall-mounting panel between the wall and the screws.
To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON; set switch 3 to OFF (the default setting) to disable the termination resistor. To set the pull-up/down resistors to 150 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to OFF. This is the default setting. To set the pull-up/down resistors to 1 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to ON.
WLAN IP Netmask Static 192.168.127.254 255.255.255.0 If the NPort is configured for DHCP but the DHCP server cannot be found, the NPort will use factory default IP settings. NOTE If you have forgotten the NPort’s IP address, use the Device Search Utility from your PC to locate the NPort. After searching the LAN for NPort units, the Device Search Utility will display the IP address of each unit.
DB9 Male (RS-232/422/485) Pin RS-232 1 2 3 4 5 6 7 8 9 DCD RxD TxD DTR GND DSR RTS CTS – RS-422/ RS-485-2W RS-485-4W TxD-(A) – TxD+(B) – RxD+(B) Data+(B) RxD-(A) Data-(A) GND GND – – – – – – – – Power Input and Relay Output Pinouts V2+ V2- V1+ V1- DC Power Input 2 DC Power Input 2 DC Power Input 1 DC Power Input 1 N.O. Common N.C.
Fault Relay Circuit FCC Part 15 Subpart B, Class A Safety UL: UL 60950-1 LVD: EN 60950-1 DSPR: ARIB-STD 33, ARIB-STD 66 3-pin circuit with current-carrying capacity of 2 A @ 30 VDC ATTENTION This product is intended to be supplied by an UL listed DC source suitable for use at TMA of 60 degree C, which output meets SELV circuit and LPS, which is separated from the primary circuit by double insulation or reinforced insulation, and is rated 12-48Vdc, 0.38-0.1A or min. 0.38A; or 24Vdc, min. 0.17A.
