NPort W2150A-W4/ NPort W2250A-W4 Series Quick Installation Guide Version 1.1, January 2023 Technical Support Contact Information www.moxa.com/support 2023 Moxa Inc. All rights reserved.
Overview The NPort W2150A-W4/W2250A-W4 wireless device servers are an ideal choice for connecting serial devices or Ethernet devices, including PLCs, meters, and sensors, to an IP-based wireless LAN or Ethernet LAN. Features • • • • • • • • • Links serial and Ethernet devices to an IEEE 802.
ATTENTION 이 기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다. ATTENTION 「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不 得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材 之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法 規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及 醫療用電波輻射性電機設備之干擾。」 「應避免影響附近雷達系統之操作。」 NOTE Before connecting the NPort W2150A-W4 and NPort W2250AW4 Series DC power inputs, make sure the DC power source voltage is stable.
NPort W2150A-W4 NPort W2150A-W4-T NPort W2250A-W4 NPort W2250A-W4-T Reset Button: The reset button is used to load the factory default settings. Use a pointed object to hold the reset button down for five seconds to load the factory defaults. Name Color Function End Panel LED Indicators Orange 10 Mbps Ethernet connection. Ethernet Green 100 Mbps Ethernet connection. Off Ethernet cable is disconnected. Top Panel LED Indicators Steady on: Power is on, and the NPort is booting up.
Name Color Red Signal Strength Green Function 1 Red - The signal strength (RSSI) is lower than -88 dBm. 2 Red - The signal strength (RSSI) is between -87 to -79 dBm. 3 Green - The signal strength (RSSI) is between -78 to -68 dBm. 4 Green - The signal strength (RSSI) is between -67 to -60 dBm. 5 Green - The signal strength (RSSI) is between -59 to -45 dBm.
First-Time Hardware Installation STEP 1: After removing the NPort W2150A-W4/W2250A-W4 from the box, use a crossover Ethernet cable to connect the NPort’s RJ45 Ethernet port directly to your computer’s Ethernet port. STEP 2: Attach the power adapter to the NPort and then plug the adapter into an electrical outlet. STEP 3: Configure the NPort W2150A-W4/W2250A-W4 through the Ethernet port. See the next section on how to install software.
Software Installation For the NPort’s configuration, the default IP address of the NPort is: LAN: Static; IP = 192.168.126.254; netmask = 255.255.255.0 WLAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0 If the NPort is configured for DHCP, but the DHCP server cannot be found, then the NPort will use the factory default IP settings. NOTE If you have forgotten the NPort's IP address, use the Device Search Utility (DSU) from your PC to locate the NPort.
Pin Assignments and Cable Wiring Pin RS-232 1 2 3 4 5 6 7 8 9 DCD RXD TXD DTR GND DSR RTS CTS – RS-422, 4w RS-485 TxD-(A) TxD+(B) RxD+(B) RxD-(A) GND – – – – 2w RS-485 – – Data+(B) Data-(A) GND – – – – Specifications Power Requirements Power Input 12 to 48 VDC Input Rating 1-port: 12 to 48 VDC, max 429 mA @ 12 VDC 2-port: 12 to 48 VDC, max 455 mA @ 12 VDC Power Connector Screw-type power jack or terminal block (only one connection at a time) Physical Characteristics Material Aluminum sheet metal (1 mm
