SDS-3008 Series Quick Installation Guide Moxa’s Industrial Smart Ethernet Switch Edition 2.0, March 2017 Technical Support Contact Information www.moxa.
Overview The SDS-3008 industrial smart Ethernet switch is the ideal device for IA engineers and automation machine builders to make their networks compatible with the vision of Industry 4.0. By breathing life into machines and control cabinets, the smart switch simplifies daily tasks with its easy configuration and easy installation. In addition, it is monitorable and easy to maintain throughout the entire product life cycle.
SDS-3008 Panel Layout 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 1 to 8 10/100BaseT(X) ports (bottom to top) System status LEDs (top to bottom) STATE LED indicator (Green), FAULT LED indicator (Red), PWR1 LED indicator (Amber), PWR2 LED indicator (Amber) 1 to 8 port status LEDs (bottom to top) • LED lights in Green: 100 Mbps • LED lights in Amber: 10 Mbps Model side label (Multiple production information included) • Default IP: 192.168.127.
Mounting Dimensions; unit = mm (inches) DIN-Rail Mounting There are 2 options for DIN-rail mounting that can be adopted on a SDS-3008. Option 1 is the default type when shipped. Option 1 (Default): When shipped, the metal DIN-rail mounting kit is fixed to the back panel of the SDS-3008. Mount the SDS-3008 on the corrosion-free mounting rail that adheres to the EN 60715 standard. Suggested Installation Method STEP 1—Insert the upper lip of the DIN-rail kit into the mounting rail.
Suggested Removal Method STEP 1—Pull down the latch on the DIN-rail kit with a screwdriver. STEPS 2 & 3—Slightly pull the SDS-3008 forward and lift up to remove it from the mounting rail. Option 2 (when side cabling is needed): The metal DIN-rail mounting kit can be fixed to the side panel (mold side) of the SDS-3008 (horizontal or vertical). Mount the SDS-3008 on the corrosion-free mounting rail that adheres to the EN 60715 standard.
STEP 2—Insert the upper lip of the DIN-rail kit into the mounting rail. STEP 3—Press the SDS-3008 towards the mounting rail until it snaps into place. Suggested Removal Method STEP 1—Pull down the latch on the DIN-rail kit with a screwdriver. STEPS 2 & 3—Slightly pull the SDS-3008 forward and lift up to remove it from the mounting rail. NOTE Screws that are used to fix the DIN-rail kit on the SDS-3008 should be securely fastened before mounting on the mounting rail.
Be sure to read and follow these important guidelines: • Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE • • • Do not run signal or communications wiring and power wiring through the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.
NOTE We suggest the length of the pin type cable terminal is 8 mm. In order to tighten the wire properly, ① use a small flathead screwdriver to press the push-in button beside each terminal of the terminal block connector before and during ② inserting the wire. ③ Release the screwdriver after the wire has been fully inserted. Please refer to the diagram below. Wiring the Relay Contact The SDS-3008 has one relay output for identifying when a specific event has occurred (i.e., fault; see below).
NOTE The relay output of the SDS-3008 reflects a potential-free, normally opened solid-state relay. Therefore, not only when user-configured events are triggered but also when there is no power supply to the switch it will open. To indicate a fault has occurred one can integrate the relay contact on the smart switch with an external alarming system circuit so that the status of user-configured events or no power supply can be monitored.
Wiring the Redundant Power Inputs (12/24/48 VDC) The SDS-3008 has two sets of power inputs–power input 1 (PWR 1/P1) and power input 2 (PWR 2/P2). The top view of the terminal block connector and the positions of the power inputs are shown below. Take the following steps to wire the redundant power inputs: STEP 1: Insert the Positive/Negative DC wires into the V1+/V1- terminal for PWR 1 and/or V2+/V2- terminal for PWR 2.
NOTE ABC-02-USB Installation Plug the ABC-02-USB into the USB storage port of the SDS-3008. We suggest securing the ABC-02-USB on the wall with an M4 screw. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on the front panel of the SDS-3008 are used to connect to Ethernet-enabled devices.
Reset Button The reset button can perform two functions. One is to reset the industrial smart Ethernet switch back to factory default settings and the other is to perform a quick back up of configuration and log files to the ABC-02-USB automatic backup configurator. Reset to Factory Default Settings Use a pointed object, such as a straightened paper clip, to depress and hold the reset button for 5 seconds. This will cause the state LED to blink once a second.
LED Color Status Description FAULT Red Solid light 1. System is in the event of failure, or is under quick inspection 2. Invalid port connection 1. RAM test fail / switch initialization fail 2.
Switch Properties Max. Number of VLANs VLAN ID Range MAC Table Size Packet Buffer Size Interface RJ45 Ports Storage Port Alarm Contact (Relay Output) Digital Input 8 VID 1 to 4094 8K 3 Mbit 10/100BaseT(X) auto negotiation speed USB storage (Type A connector for ABC-02-USB) 1 normally open solid-state relay output with current carrying capacity of 1 A @ 24 VDC 1 input with the same ground, but electrically isolated from the electronics. • +13 to +30 V for state “1” • -30 to +3 V for state “0” • Max.
Standards and Certifications Safety UL 61010-2-201, EN 60950-1 (Preliminary) EMC EN 61000-6-2/6-4 EMI CISPR 22, FCC Part 15B Class A EMS IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 20 V/m IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV IEC 61000-4-6 CS: Signal: 10 V IEC 61000-4-8 PFMF: 300A/m, 60 s Shock IEC 60068-2-27 Freefall IEC 60068-2-32 Vibration IEC 60068-2-6 Note: Please check Moxa’s website for the latest certification s
