Moxa 802.11a/b/g/n/ac WAPC003 User’s Manual www.moxa.com First Edition, Jan 2021 2021 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
WAPC003 User’s Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright 2021 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers.
Table of Contents Chapter 1 Introduction Overview Specification Chapter 2 Getting Started Module Layout Block Diagram Hardware Installation Software Installation
WAPC003 User’s Manual Introduction 1 C hapter 1 The following topics are covered in this chapter: Overview Specifications Introduction
WAPC003 User’s Manual Introduction Overview WAPC003 module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via 2.4GHz/5GHz channels. The WAPC003 uses the IPQ4029 SoC Wireless chipset from Qualcomm Atheros. Specification Features Chipset Baseband Processor (BBP) security engine Connectors Power requirement Dimension Operating Temperature Storage Temperature: Operates in 2.4 and 5 GHz frequency bands.
WAPC003 User’s Manual 802.11ac (2.4GHz) • Typ. 26±1.5dBm @ MCS0, MCS0*2 20 MHz • Typ. 22±1.5dBm @ MCS8, MCS8*2 20 MHz 802.11a • Typ. 23±1.5 dBm @ 6, 9, 12Mbps • Typ. 22±1.5 dBm @ 18, 24, 36, 48 Mbps • Typ. 21±1.5 dBm @ 54 Mbps 802.11n • Typ. 23±1.5 dBm @ MCS0 to MCS2 20MHz • Typ. 22±1.5 dBm @ MCS3, MCS8 to MCS10 20 MHz • Typ. 21±1.5 dBm @ MCS4 to MCS6, MCS11 to MCS14 20MHz • Typ. 20±1.5 dBm @ MCS7, MCS15 Mbps RX Receive Sensitivity: 802.11ac • Typ. 23±1.
WAPC003 User’s Manual • • • • • -76 dBm @ MCS13 20 MHz -75 dBm @ MCS14 20 MHz -74 dBm @ MCS5, MCS15 20 MHz -72 dBm @ MCS6 20 MHz -71 dBm @ MCS7 20 MHz 802.11a (4,920 & 4,98 0 MHz): • -90 dBm @ 6 Mbps • -88 dBm @ 9 Mbps • -87 dBm @ 12 Mbps • -85 dBm @ 18 Mbps • -83 dBm @ 24 Mbps • -79 dBm @ 36 Mbps • -75 dBm @ 48 Mbps • -72 dBm @ 54 M bps 802.
WAPC003 User’s Manual • -68 dBm @ MCS8*2 20 MHz • -66 dBm @ MCS8 20 MHz Introduction
2 C hapter 2 Getting Started This chapter covers the module layout, and block diagram, hardware installation of the WAPC003. Software installation is covered in the next chapter.
WAPC003 User’s Manual Module Layout Top Bottom Getting Started
WAPC003 User’s Manual Block Diagram Below is a block diagram of the WAPC003.
WAPC003 User’s Manual Connector Locations Getting Started
WAPC003 User’s Manual Getting Started PCI Bus Connector PIN Assignments 5V 5V 5V 5V GND GND USB2_DM USB2_DP GND GND PCIE_REFCLKPCIE_REFCLK+ GND GND PCIE_RXPCIE_RX+ GND GND PCIE_TXPCIE_TX+ GND GND EMMC_D0 GND EMMC_D1 GND EMMC_D2 GND EMMC_D3 GND EMMC_D4 GND EMMC_D5 GND EMMC_D6 GND EMMC_D7 GND SDIO_CMD GND SDIO_CLK B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12
WAPC003 User’s Manual GND SDIO_CD GND GND XN3_3 XP3_3 GND GND XN3_2 XP3_2 GND GND XN3_1 XP3_1 GND GND XN3_0 XP3_0 GND B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 Getting Started A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 UART_DTR_1 UART_DSR_1 GND GND XN4_3 XP4_3 GND GND XN4_2 XP4_2 GND GND XN4_1 XP4_1 GND GND XN4_0 XP4_0 GND
WAPC003 User’s Manual Getting Started Hardware Installation The WAPC003 can be installed into Moxa wireless system board series. Step for Installation 1. Install the WAPC003 module on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPC003 module. 3. Screw on the all the necessary chassis.
WAPC003 User’s Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WAPC003 User’s Manual Getting Started This radio transmitter FCC ID: SLE-WAPC003 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
WAPC003 User’s Manual Getting Started Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie rayonnée du dispositif sans fil est inférieure aux limites d'exposition aux radiofréquences d'Innovation, Sciences et Développement économique Canada (ISED). Le dispositif sans fil doit être utilisé de manière à minimiser le potentiel de contact humain pendant le fonctionnement normal.
WAPC003 User’s Manual Getting Started 「帯: W52/53 屋内使用限定 ただし登録局に接続される場合は除く」“Band: W52/53 indoor usage only *except for connection to the registered station“ NCC警語 : 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善 至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫 療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求最終產品平台廠商 (OEM Integrator) 於最終產品平台(End Product)上標示” 本產品內含射頻模組，其 NCC 型式認證號碼為: CCXXxxYYyyyZzW 應避免影響附近雷達系統之操作。
