DOOR-TYPE EXTENDED HOOD SERIES DISHWASHERS Installation/Operation Manual with Service Replacement Parts For machines beginning with S/N D3684 up to S/N D10048290 and above Door-type Extended Hood Dishwasher Models: D-HBTM5, MDHH, DHBTCM5 High Temperature Extended Hood with Built-in Booster Heater D-H1TM5, DH1TCM5 High Temperature Extended Hood without Built-in Booster Heater Issued 3.8.11 Manual P/N 113492 rev. i 3765 Champion Boulevard, Winston-Salem, NC 27105 1-800 858-4477 Fax: 336 661-1660 2674 N.
For future reference, record your dishwasher information in the box below. Model Number__________________________ Serial Number_______________________ Voltage________________Hertz_____________ Phase__________________ Service Agent __________________________________ Tel:______________________ Parts Distributor _________________________________ Tel:______________________ National Service Department In Canada: Toll-free: 800/ 263-5798 Tel: 905/ 562-4195 Fax: 905/ 562-4618 email: service@moyerdiebellimited.
In Canada you can Register by Postage Paid Mail: Cut along the dashed lines, then complete the back of the postage paid card above and mail immediately to validate your machine warranty. OR REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then click or enter the address below. In the U.S.A http://www.championindustries.com/register In Canada http://www.championindustries.
PRODUCT REGISTRATION CARD Serial # Model Date of Installation: Company Name: Address: Telephone #: ( ) --- (Street) Province Postal Code Contact: Installation Company: Address: Telephone #: Contact: FAILURE TO REGISTER YOUR PRODUCT MAY VOID YOUR WARRANTY IMPORTANT IMPORTANT REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then click or enter the address below. In the U.S.A http://www.championindustries.com/register In Canada http://www.championindustries.
Revision History Revision History A revision might be a part number change, new instructions, or information that was not available at the time of printing. We reserve the right to make changes to this manual without notice and without incurring any liability by making changes. Dishwasher owners may request a revised manual at no charge by calling (800) 858-4477 in the USA or (800) 263-5798 in Canada. Revision Date Pages Serial No. Effectivity Description 7.1.
Revision History (continued) Revision History (continued) Revision Date Pages 1.6.10 All D09117934 Release of Second Edition 8.6.10 25, 59 D10048290 Added Moyer Diebel Panel labels P/N's 8.6.10 27 D10048290 Added Moyer Diebel Door P/N 8.6.10 51 D10048290 Added 575V Xfmr P/N 111521 3.8.11 36-37 All Added P/N 114861 Item 9 to parts list ii Serial No.
Model Descriptions Model Numbers Model Descriptions D-HBT and MDHH - Straight-through with built-in booster D-HBTC - Corner with built-in booster D-H1T - Straight-through without built-in booster D-H1TC - Corner without built-in booster Standard Equipment Automatic Tank Fill and start Adjustable cycle selector switch Combination dishwasher for dishes, pots, pans and utensils Built-in electric booster heater (DHBT, DHBTC only) in 40˚F/22˚C rise for 140˚F/60˚C supply water Specified as straight-through or
Limited Warranty LIMITED WARRANTY Champion Industries Inc. and Moyer Diebel (herein referred to as "The Company"), 3765 Champion Blvd., Winston-Salem, North Carolina 27105, and P.O. Box 301, 2674 N. Service Road, Jordan Station, Canada, L0R 1S0, warrants machines, and parts, as set out below.
Table of Contents Table of Contents Model DHBT, MDHH, DH1T Extended Hood Door-type Dishwashers Revision History................................................................................................................... i Model Descriptions............................................................................................................... iii Limited Warranty..................................................................................................................
Blank Page This Page Intentionally Left Blank vi
Installation Receiving !!ATTENTION!! Use caution when moving or lifting the dishwasher to prevent damaging the dishwasher or the installation site. Check doorway and passageway clearance before moving the dishwasher. Remove dishwasher front panel and check under the machine base for obstructions before moving. 1. Inspect the dishwasher for shipping damage 2. Check the dishwasher interior for curtains, panels and other supplies. 3.
Installation Electrical Connections WARNING: Electrocution or serious injury may result when working on an energized circuit. Disconnect power at the main breaker or service disconnect switch before working on the circuit. Lock-out and tag the breaker to indicate that work is being performed on the circuit.
Installation Electrical Connections A qualified electrician MUST compare the electrical power supply with the machine electrical specifications stamped on the MACHINE ELECTRICAL CONNECTION PLATE located on the base of dishwasher near the main terminal block. MACHINE ELECTRICAL CONNECTION !!ATTENTION!! Electrical and grounding connections must comply with the National Electrical Code or in the absence of a National Code then all Local Electrical Codes. 3.
Installation Hot Water Connections NOTE: Only qualified personnel should make dishwasher plumbing connections. Connections must meet local plumbing and sanitary codes. Improper installation is not covered by the dishwasher warranty. Hot Water Requirements: 1. Connect a 3/4" NPT hot water supply line to the line strainer located above the base of the dishwasher. Refer to the illustrations below. 2.
Installation Drain Connections 1. All models are GRAVITY DRAIN machines equipped with a 2" O.D. hose connection. 2. The maximum flow rate is 15 U.S. gpm/56.8 Lpm. 3. Drain height for all models must not exceed 8-7/8" [225mm] above the finished floor. 4. The drain connection is made to the dishwasher from underneath the machine. An access hole is provided in the machine base. 2" O.D. Hose Fitting Ventilation Connections Vent NOTE: DO NOT VENT THE DISHWASHER INTO WALLS, CEILINGS OR ENCLOSED PLACES. 1.
Installation Steam Coil Tank Heat and Steam Booster Heater The illustration below details a steam heated machine consisting of a tank heat steam coil and a mounted steam booster for the final rinse. Contact the factory for steam injector tank heat details. NOTE: Only qualified personnel should make dishwasher steam connections. Connections must meet local plumbing and sanitary codes. Improper installation is not covered by the dishwasher warranty.
Installation Single Source Gas Booster Heater The illustration below details a single source gas heated machine consisting of a tank heat hot water coil and a gas-powered booster heater for the final rinse. The gas-powered booster provides hot water for the hot water coil and the final rinse. The booster will run on natural gas or propane which is specified at the time of order. NOTE: Only qualified personnel should make dishwasher gas connections. Connections must meet local gas and sanitary codes.
Installation Purging Air from the Dishwasher/Booster Heater System CAUTION: PERMANENT DAMAGE to the hot water recirculating pump can occur if the air is not purged from the dishwasher/booster heater system prior to placing the dishwasher into service. Follow the instructions carefully to prevent damage to the dishwasher hot water recirculating pump. Follow the procedure below to purge the air from the system. Plumbing and electrical service connections must be completed before purging the system.
Installation Chemical Signal Connections 1. Use a qualified detergent/chemical supplier for detergent/chemical and dispensing equipment needs. 2. Labeled detergent control circuit connection terminals are provided in the control cabinet for detergent and rinse agent dispensing equipment (supplied by others). 3. The illustration below shows the terminal board for the machine. 4. The signal connection points include: • Detergent signal 120VAC, 1A max load. • Rinse aid/Sanitizer signal 120VAC, 1A load. 5.
Installation Door Safety Switch Dishwasher access doors are equipped with a door safety switch that automatically stops the dishwasher pump if a door is raised while the dishwasher is running. In addition, the dishwasher will not start if a door is left open. 1. If the dishwasher is running and a door is raised, then lighted in-cycle light goes out and the pump stops. 2. Check the interior of the dishwasher for a dish rack still in the machine.
Installation Scrap Screens and Screen Support 4. Make sure the scrap screen support is positioned across the wash tank and installed in the brackets at the front and rear of the tank. 5. Install the scrap screens.
Initial Start-Up Check list 1. Remove white protective film from the dishwasher exterior. 2. Install lower panels to the dishwasher. 3. Remove any foreign material from inside of the machine. 4. Check dishwasher drain/overflows are closed and in securely seated. 5. Install scrap screens, spray arms. 6. Turn main utilities to the dishwasher ON. (Power, water). 7. Make sure doors are closed. 8. Turn dishwasher power switch ON. 9. Check that the wash tank water temperature reaches a minimum of 150˚F/60˚C. 10.
Operation Control Panel Refer to the illustration below and the explanation of the control panel controls located at the lower front of the dishwasher.
Operation Operation The following steps describe the operation of the dishwasher. 1. Make sure the main power and water supplies are turned on and the dishwasher doors are closed. 2. Push the power switch to the ON position. The power switch will illuminate and the machine will fill with water. WASH CYCLE POWER 1 MIN CYCLE ON 2 MIN OFF 3 MIN 6 MIN WASH TEMPERATURE RINSE PRESSURE 3. Wait approximately 10 minutes for the wash tank temperature gauge to reach a minimum of 150˚F/60˚C.
Operation Operation Setting the Wash Cycle Selector Switch The selector switch provides 4 time options, 2 for dishes and 2 for pots and pans. To select a time cycle: 1. Make sure the power is on. 2. Make sure the cycle light is out. The time cycle cannot be changed if the dishwasher is actively running a timed cycle. 3. Make sure all doors are closed. WASH CYCLE POWER 1 MIN CYCLE ON 2 MIN 3 MIN OFF 6 MIN 4. Turn the wash cycle selector knob to either 1, 2, 3, or 6 minute setting.
Operation Operation (continued) 6. Load a dish rack into the dishwasher and close the doors. WASH CYCLE POWER 1 MIN CYCLE ON 2 MIN 7. The cycle will begin automatically and the cycle light will illuminate. 3 MIN 6 MIN WASH TEMPERATURE RINSE PRESSURE 8. Open the doors and the cycle will automatically stop. 9. Close the doors and the cycle will resume where it left off. 10.
Operation Operation Summary ACTION 1. Push ON/OFF switch UP to the ON position. 2. Wait 10 minutes for water to reach proper temperature. 3. 4. Prescrap and load wares into the dish racks. Open the doors, insert a dish rack of soiled ware and close the doors. Opening the doors anytime during the automatic cycle stops the dishwasher. Closing the doors will resume the cycle where it left off. RESULT The power switch illuminates, machine fills automatically and wash water begins to heat.
Cleaning Cleaning Cleaning your dishwasher is the best maintenance you can perform. The cleaning intervals below are the minimum requirements for most dishwashers. You may need to clean your dishwasher more often when washing heavily soiled wares or during long hours of continuous operation. POWER ON OFF To Drain The automatic drain valve will open for 10 minutes to drain the dishwasher when the Power Switch is turned off. Daily or every 2 hours of operation 1. Turn power switch to OFF.
Cleaning De-liming De-liming Lime (scale) deposits are the result of minerals contained in the water feeding the dishwasher and appear as a white haze on the surface of the dishwasher. Severe scaling can appear as a granular deposit. These deposits are a result of the mineral content in the geographic area of the machine's location. WARNING: Death or injury can result from toxic fume when de-liming agents come in contact with Chlorine Bleach, or other chemicals that contain iodine, bromine, or fluorine.
Maintenance Maintenance Weekly 1. Inspect all water lines for leaks and tighten at joints if required. 2. Clean any detergent residue from the exterior of the machine. 3. Check that the drain/overflow pipes seat tightly in their drains. 4. Clean any accumulated scale from the heating element. 5. Inspect the spray arms for any damage or missing parts. 6. Inspect the final rinse arms for missing parts. 7. Check that float switch moves freely. Monthly 1.
Troubleshooting Before calling for service check the following conditions. Troubleshooting 1. Dishwasher main power and water supply is on. 2. Machine has been assembled correctly. 3. Drain is closed. 4. Screens and pump intake screen are clear. 5. Doors are closed and secure. Condition Cause Solution Dishwasher will not run. Door not closed. Main power OFF Dishwasher Power OFF. Close door completely. Check breaker on panel. Turn dishwasher ON. Machine washes constantly.
Troubleshooting Troubleshooting (continued) Condition Cause Insufficient pumped spray pressure Clogged pump intake screen. Clogged spray arm. Scrap screen full. Pump motor rotation wrong Defective pump seal. Clean. Insufficient or no final rinse spray pressure Main water supply off. PRV setting incorrect Solenoid strainer clogged. Solenoid valve defective. Clogged rinse nozzles. Open supply valve. Adjust the PRV setting Clean strainer. Contact Service Agent. Clean with paperclip. Clean. Clean.
Service Replacement Parts Service Replacement Parts Illustration Page DHBT, DH1T, MDHH Panels.......................................................................................................................24 DHBT, DH1T, MDHH Doors.........................................................................................................................26 DHBTC, DH1TC Doors................................................................................................................................
24 6 7 5 6 8 9 7 8 10 12 9 11 9 1 2 3 4 10 11 10 DHBT, DH1T Panels
DHBT, DH1T Panels Item No. Part No.
DHBT, DH1T Doors 1 2 3 4 5 6 8 10 9 7 11 11 20 13 12 12 18 27 16 26 16 14 24 17 17 16 24 25 19 23 22 20 21 20 21 26 10 15 15
DHBT, DH1T Doors Item No. Part No. Description Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 --- 100141 317345 325921 108053 107970 112704 112705 112703 112702 100073 111090 108954 322790 327248 GRIP NUT, 1/4-20 SST BRACKET, DOOR CATCH HOOK, DOOR CATCH PLUG, CORNER POST SCREW, 8/32 X 1" FILISTER DOOR GUIDE, SIDE DOOR LEFT DOOR GUIDE, SIDE DOOR RIGHT DOOR GUIDE, FRONT DOOR LEFT DOOR GUIDE, FRONT DOOR RIGHT SCREW, 1/4-20 X 1/2" TRUSS HD.
DHBTC, DH1TC Doors 1 2 3 4 3 4 21 21 22 22 5 5 17 12 16 13 16 15 15 20 13 12 19 24 6 11 7 22 10 8 14 9 22 8 9 28 23 24 23 8 9
DHBTC, DH1TC Doors Item No. Part No. Description Qty 1 108053 PLUG, CORNER POST 2 2 107970 SCREW, 8-32 X 1" FILISTER HD. SST 32 3 112704 GUIDE, DOOR LEFT 2 4 112705 GUIDE, DOOR RIGHT 2 5 325633 DOOR, SIDE UPPER 2 6 322788 DOOR, LOWER SIDE (PRIOR TO S/N D3864) 1 --- 327252 DOOR, LOWER SIDE (BEGIN W/ S/N D3864) 1 7 323221-S DOOR, LOWER FRONT (PRIOR TO S/N D3864) 1 --- 327295 DOOR, LOWER FRONT (BEGIN W/ S/N D3864) 1 8 100007 SCREW, 10-32 X 3/8" TRUSS HD.
Door Handle and Spring Assembly 28 29 No longer used after S/N D5748 See Door Assemblies for Reed Switch Replacement.
Door Handle and Spring Assembly Item No. Part No. Description Qty 1 2 3 4 --5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 --22 23 24 25 26 27 28 --29 --- 112723 108066 107397 113757 112860 107347 107396 107393 107962 107395 107420 107436 107399 108368 304811 100740 107966 322077 100097 0509264 0509274 0309167 322926 102376 104002 100154 106013 102376 321927 113721 0509199 0309451 328173 BOLT, 5/6-18 X 15" SPRING, EXTENSION BLOCK, SPRING HOOK DOOR HANDLE, STD.
Track Assembly 1 2 2 1 3 4 Straight-through Track Assembly 3 4 3 4 2 3 4 6 2 6 8 6 1 6 7 8 7 9 10 6 7 9 10 4 6 11 7 5 11 Corner Track Assembly 7 8 9 10 32 7 3 9 10 8 2
Track Assembly STRAIGHT-THROUGH TRACK CONFIGURATION Item No. 1 2 3 4 Part No. 0309472 100073 106482 100003 Description TRACK, REAR BOLT, 1/4-20 X 1/2" TRUSS HD., SST WASHER, LOCK 1/4" SPLIT SST NUT, PLAIN 1/4" HEX HD., SST Qty 1 8 8 8 CORNER TRACK CONFIGURATION Item No. 1 2 3 4 5 6 7 8 9 10 11 Part No. 0309469 0309472 0309468 0309470 0309471 106727 107966 100073 106482 100003 0309473 Description GUIDE, RIGHT HAND TRACK, REAR GUIDE, LEFT HAND SUPPORT, RACK TRACK, FRONT SCREW, 10-32 X 5/8" FLAT HD.
Wash and Rinse Spray Piping 2 3 7 8 1 5 6 4 10 2 12 11 13 34 5 7 9 10 3 8 FR ON T F LE E ID TS
Wash and Rinse Spray Piping Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No. 325632 113027 113028 0507445 109864 113252 100736 107967 109854 100740 106013 102376 100154 Description MANIFOLD, RINSE CONNECTOR, RINSE ARM CONNECTOR, TOP RINSE ARM SPINDLE, WASH ARM SUPPORT, WASH ARM STANDPIPE, WASH BOLT, 1/4-20 X 3/4" HEX HD., SST GRIP NUT, 1/4-20 SST GASKET, WASH STANDPIPE BOLT, 5/16-18 X 1" HEX HD.
Wash and Rinse Spray Arms 2 1 2 3 4 3 9 Prior to S/N D3863 1 3 Beginning with S/N D3863 and above 4 3 9 5 6 7 8 36
Wash and Rinse Spray Arms Item No. Part No. Description Qty 1 2 3 0507443 0508376 113514 SPINDLE, RINSE ARM NOZZLE, RINSE ARM (PRIOR TO S/N D3864) BEARING, RINSE ARM (REPLACES 112164) 2 12 4 4* 414111 RINSE ARM ASSY, (INCLUDES 2 & 3) (PRIOR TO S/N D3864) 2 ---- 414110 RINSE ARM ASSY COMPLETE (BEGIN D3864) 2 5 6 7 8 9 0507444 109835 0707452-S 0507446 114861 NUT, RINSE ARM SCREW, #8 X 1/2" PAN HD.
Scrap Screens and Drain Assembly 1 17 3 2 4 4 5 15 14 16 6 13 7 8 11 9 8 10 12 11 38
Scrap Screens and Drain Assembly Item No. Part No. Description Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 --- 305164 324582 100736 106026 107967 304816 205988 104165 205990 114471 107340 113048 324573 113047 106482 100003 327283 327098 SCREEN, SCRAP 10" PLATE, FILLER BOLT, 1/4-20 X 3/4" HEX HD.
Wash Tank Heat and Thermostats 7 8 16 8 5 7 Th 16 erm 15 ost at b rac ket 4 3 det ail 5 2 20 18 1 19 6 18 4 3 14 11 12 13 40 17 10 9
Wash Tank Heat and Thermostats Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 113622 109069 201041 201029 322076 110561 106482 100003 100740 108345 102376 106013 100154 0509637 Description THERMOMETER, 4FT. CAPILLARY THERMOSTAT W/CAPILLARY WASHER NUT, LOCK 1/2" BRACKET, DUAL THERMOSTAT THERMOSTAT, FIXED HIGH-LIMIT WASHER, LOCK 1/4" SPLIT, SST NUT, PLAIN 1/4-20 HEX HD., SST BOLT, 5/16-18 X 1" HEX HD.
42 2 1 12 NG IPI ER P UP P 2 1 TO 11 4 F E LV A V 10 ILL F M RO 3 8 9 7 6 5 Electric Booster Assembly
Electric Booster Assembly Item No. Part No. Description Qty 1 2 3 4 --5 6 7 100740 102376 108954 110562 110563 109069 100003 106482 BOLT, 5/16-18 X 1" HEX HD.
k2 Steam Booster Assembly 31 13 14 13 28 7 4 16 29 9 28 8 4 27 25 20 5 26 6 5 12 4 22 11 17 23 24 18 3 30 18 21 22 19 28 4 18 26 24 15 23 3 4 1 5 10 27 28 29 18 19 24 18 4 44 23 25 2 4 13 10 12 31 2 3 5
K2 Steam Booster Assembly Item No. 1 2 3 4 5 6 7 8 ----9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 ----28 29 30 31 Part No.
Hot Water Coil Tank Heat Assembly NOT SHOWN 1 2 3 4 3 5 1 2 9 5 6 3 3 5 2 12 11 5 3 17 12 5 6 7 1 3 4 11 11 3 15 8 5 GRUNDFOS 5 5 13 3 14 46 15 16 14 9 10 19
Hot Water Coil Tank Heat Assembly Item No. Part No.
Single Source Gas Booster Piping STANDARD REAR FLUE EXHAUST OPT.
Single Source Gas Booster Piping Item No. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 102521 100184 107550 102651 102669 102660 102442 102678 106911 100571 102525 110768 109879 112228 105779 105752 105803 113003 105806 100113 105731 100118 102526 102504 109925 102392 TEE, 3/4" NPT BRASS NIPPLE, CLOSE 3/4" NPT BRASS PRESSURE REGULATING VALVE 3/4" NPT BRONZE NIPPLE, 3/4" NPT X 2" LG. BRASS NIPPLE, 3/4" NPT X 8-1/2" LG. BRASS NIPPLE, 3/4" NPT X 6" LG.
DHBT Lower Fill Piping Assembly 15 16 14 13 2 17 3 18 4 12 5 9 11 8 10 2 6 1 5 5 7 19 5 CUSTOMER WATER INLET 50 TO UPPER PIPING
DHBT Lower Fill Piping Assembly Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No.
DHBT, DH1T Upper Fill Piping Assembly 11 7 12 4 3 15 9 14 8 2 3 16 10 8 WATER IN FROM LOWER PIPING 13 5 6 1 52
DHBT, DH1T Upper Fill Piping Assembly Item No. Part No. 1 2 3 100156 100571 102392 --- 100171 4 5 6 7 8 9 10 11 12 13 14 15 16 100599 108181 107463 102444 100184 113222 109925 102489 104682 102521 102505 113223 102392 Description LOCKNUT, 3/4" NPT BRASS UNION 3/4" NPT BRASS BUSHING, RED. 3/4" NPT X 1/2" BRASS (PRIOR TO S/N D3699) BUSH, RED., FACE 3/4" NPT X 1/2" BRASS (BEGIN WITH S/N D3700) CROSS, 3/4" NPT BRASS BUSHING, RED.
DH1T Lower Fill Piping Assembly TO UPPER PIPING 11 10 1 9 2 7 3 5 4 6 8 6 CUSTOMER WATER IN 1 20 19 15 12 13 18 17 16 54 14
DH1T Lower Fill Piping Assembly Item No. 1 2 3 4 5 --6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Part No. 102444 0309340 110768 111437 109903 111472 100184 102442 102470 102392 109925 205824 102525 102388 101261 112437 107065 107928 111100 109812 109765 Description STREET ELL, 3/4" NPT BRASS BRACKET, PLUMBING SUPPORT STRAINER, LINE 3/4" BRASS VALVE, 3/4" NPT HOT WATER, 12OVAC KIT, REPAIR VALVE, 3/4" NPT HOT WATER COIL.
56 3 1 7 2 8 9 10 12 11 4 13 6 17 16 5 18 19 21 22 20 23 14 24 25 32 26 31 28 27 30 29 Pump Assembly
Pump Assembly Item No. Part No.
Control Panel Assembly POWER WASH CYCLE 4 CYCLE 6 5 1 MIN 2 MIN 4 MIN Prior to S/N D3864 6 MIN 2 OFF 1 3 WASH 160 8 90 psi 105 0 F 10 CHAMPION INDUSTRIES, INC.
Control Panel Assembly Item No. Part No. Description Qty 1 --2 3 --4 5 6 7 8 9 10 0501361 111980 112390 112391 106364 113054 113055 113056 112086 113622 109812 109756 SWITCH, ON/OFF (PRIOR TO D3863) CIRCUIT BRKER, ON/OFF (BEGIN WITH D3863) LIGHT, RED (PRIOR TO D3863-NO LONGER USED) LIGHT, AMBER (PRIOR TO D3863) PILOT, LIGHT 120V GREEN (BEGIN D3863) SWITCH, TIME SELECT, 4 POSITION CONTACT BLOCK, NO CONTACKT BLOCK NC OVERLAY, WASH 150°F THERMOMETER, 4FT.
1 60 13 1 N T10 2 EXT. WASH T9 T8 FLOAT SW. DOOR SW. T7 START SW.
Control Cabinet Assembly Item No. Part No.
Dish racks, PRV 1 2 3 62
Dish racks, PRV Item No. 1 2 3 Part No.
Blank Page This Page Intentionally Left Blank 64
DIAGRAM STATE POWER OFF DOORS CLOSED TANKS EMPTY END OF CYCLE L1 L2 L3 ON SINGLE PHASE MACHINES OMIT L3. 1MOL L1 L2 NOTE 1: IF SUPPLY VOLTAGE IS 115V, T1 IS NOT USED. WIRES #1 AND 2 ARE CONNECTED TO THE FUSE BLOCK IN PLACE OF WIRES #39 AND 40. 24 50 NOTE 2: DS1 NOT USED ON CORNER MACHINE MODELS. ! ATTENTION - VERY IMPORTANT ! - VERIFY CIRCUIT BOARD PART NUMBER AND JUMPER POSITION SETTINGS (JB1, JB2, JB3) PER MACHINE MODEL AND SERIAL NUMBER AS INDICATED IN TABLE BELOW.
