User Manual
Contents MOZA AirCross 2 Overview Installation and Balance Adjustment 1 2 Installing the Battery 2 Attaching the Tripod 2 Unlocking Motors 2 Mounting the Camera 3 Balancing 3 Buttons and OLED Display 4 Button Functions 4 LED Indicators 5 Main Interface 5 Menu Description 6 8 Features Description Camera Control 8 Motor Output 9 PFV,Sport Gear Mode 10 Manual Positioning 11 Button Customization 11 Inception Mode 11 Balance Check 12 Sensor Calibration 13 Language Switch 14
AirCross 2 Overview 21 19 20 23 22 24 11 12 25 13 14 26 15 29 27 30 28 10 16 31 17 32 18 3/8”Screw 17 USB Type-C 25 Pan Motor Lock Tilt Motor 10 Trigger 18 Battery Level 26 OLED Screen Tilt Arm 11 Roll Motor Lock 19 Safety Lock 27 Joystick Camera Control Port 12 Pan Knob 20 Roll Motor Lock 28 Dial Wheel Baseplate Knob 13 Smart Wheel 21 Multi-CAN Port 29 USB Port Pan Arm 14 Indicator Light Ring Power Button 22 Roll Arm 30 Multi-CAN Port 23 Roll Knob 3
Installation and Balance Adjustment Installing the Battery a. Press the battery lock downwards; b. Take out the battery; c. Remove the insulating film at the electrode; d. Attach the battery electrode to the gimbal. e. Press the battery into the hatch c d b e a Attaching the Tripod Attach the tripod to stand the gimbal. a. Screw the tripod tightly into the 1/4" hole at the bottom of the gimbal. b.
Mounting the Camera Horizontal Mounting b. Loosen the quick release knob screw, Pull out the safety lock at the end of the quick-release knob, insert the shorter end of the L-Bracket into the quick release baseplate, and then lock the knob. a. Place the longer side of the L-Bracket under the camera, and lock the camera with a 1/4”screw. Vertical Mounting a. Place the longer side of the L-Bracket under the camera, and lock the camera with a 1/4”screw. b.
c. Loosen the knob of the roll arm, adjust roll arm leftwards and rightwards until it remains horizontal, and then lock the knob. d. Hold the gimbal horizontally to make the pan arm level with the ground, then loosen the knob on the pan arm, adjust the pan arm leftwards and rightwards until it remains level, and then lock the knob. Note: Please release the motor lock of the axes before balance adjustment, otherwise it can’t be adjusted accurately.
OLED Display A B Tilt C D 50 L Roll 50 L Pan 50 F F E A: Smart wheel working modes Controlling external follow focus motor 1 Controlling external follow focus motor 2 Electronic follow focus Controlling the tilt axis Controlling the roll axis Controlling the pan axis B: Focus motor connection status. Icon will be displayed after connection,otherwise it won’t be displayed. Up to two focus motors can be connected at the same time. C: Camera connection status.
Menu Description L1 L2 camera L3 Shutter Cable MCSC-Multi MCSC-Multi/C MCSC-Remote M3C-USB ISO TV AV switch power motor filter switch follow speed deadband joystick wheel gimbal operation trigger L4 L5 Value * * * * * 32--106400 30--1/8000 F1--F22 ？/ok autotune ？/ok ultra light * light * level medium * heavy * ultra heavy * tilt 0-100 custom roll 0-100 pan 0-100 tilt 0-100 roll 0-100 pan 0-100 tilt on/off roll on/off pan on/off tilt 0-100 roll 0-100 pan 0-100 tilt 0-100 roll 0-100 pan 0-100
L1 gimbal L2 operation L3 dial LED L4 L5 Value habits switch brightness +/？/ok 0-100 ？/ok switch set A set B Clear AB Guidance switch set A set B Clear AB Guidance ？/ok/err ？/ok/err ？/ok/err ？/ok/err > ？/ok/err ？/ok/err ？/ok/err ？/ok/err > > 0--100 ？/on/off ？/on/off ？/on/off 0-100 0-100 on/off on/off on/off ？/ok ？/ok 0-100 0-100 0-100 * * ？/ok ？/ok ？/ok ？/ok ？/ok ？/ok ？/ok autotune balance chk F1 iFocus F2 advanced inception Dolly Zoom speed switch motion sensing tilt roll pan speed speed
3. Filtering parameters: When the motor vibrates with highfrequency, the value should be turned down. When the motor vibrates with low-frequency, the value should be increased. 4. The manual positioning function has lower priority than the following function. When using manual positioning functionnormally, following function of the axis should be turned off. Features Description Camera Control The AirCross 2 can support camera video recording, photo taking and electronic focus control.
c. After selecting the camera type and connecting the camera control cable, press the menu button once to achieve recording and press it twice to achieve photo taking. Note: 1. Cameras equipped with Micro USB 3.0 interface, such as the Nikon D850, can be normally controlled by half plugging the M3C-Micro cable. 2. After plugging the camera control cable, please operate the camera according to the prompts on the camera screen, otherwise the camera control function may not work properly.
PFV, Sport Gear Mode When the follow function is enabled, the camera will follow the movement of the gimbal. Users can enable the follow mode of each axis thru dial buttons and turn the dial to adjust the following speed, which can be also enabled in the menu. Follow Mode Switch Example 1 Example 2 Enter the tilt follow Exit the tilt follow Enter the roll follow Exit the roll follow Note: 1. The AirCross 2 is in pan follow mode by default. 2.
Manual Positioning Manual positioning is used to quickly adjust the lens orientation. When manual positioning is enabled, turn the camera orientation by hand and the camera will stay in the final direction without returning to the initial position. The adjustment speed is faster than that of using the joystick control or follow control. The manual positioning of the tilt axis is enabled by default on the AirCross 2. Manual positioning of the roll and pan axes can be enabled in the menu.
to a specified angle, the gimbal stops. ● Turn the dial: adjust the rotation speed ● Press the left button on the dial once: the gimbal rotates to the left automatically.If the gimbal is rotating, press once to stop. ● Press right button on the dial once: the gimbal rotates to the right automatically.If the gimbal is rotating, press once to stop.
Sensor Calibration Gyroscope Calibration Turn on the gimbal and leave it quietly for about 5 minutes, the gyroscope calibration is required when the gimbal drifts obviously. The steps are as follows: a. Turn on the gimbal（long press the power button） b. Turn off the motors（double press the power button/enter the menu, select gimbal>motor>switch, set ‘off’） c. Leave the AirCross 2 on the table and don't shake it or the desktop. d.
camera > iFocus > gimbal > inception advanced > manual pos >> > general > calibration > gyro tilt acc angle offset > [0] tilt [1] roll [0] roll [0] pan [0] pan [0] Notes: 1.The offset can only adjust the angle of each axis within the range of about ±5°, if there is too much offset, the camera cannot be completely leveled. 2.Offset is only a temporary solution, after shooting, accelerometer calibration is still needed. 3.
Extension Manfrotto Quick Release System The AirCross 2 is equipped with a Manfrotto quick release baseplate and a plate which make it facile for users to change shooting equipment. When using the Manfrotto quick release system, please install the baseplate onto the longer end of the L-Bracket, so that the knob screw onto the baseplate is exposed. Then fix the camera onto the release plate.
Smartphone and PC Connection The AirCross 2 is equipped with BLUETOOTH 4.0 and can be connected with smartphones. Users can set parameters, shot time-lapse video, upgrade firmware and make other operations via the MOZA Master App. With a Type-C USB interface, the AirCross 2 is able to be connected to a computer. Users can set parameter, upgrade firmware and make other operations via the MOZA Master software. Download Link: https://www.gudsen.com/moza-aircross-2 Note: 1.
Upgrade via App: a.Turn off the gimbal. b.Long press the center button, then press the power button with the other hand until the prompt ’Boot Mode’ appears on the screen. c.Start App, press Bluetooth to search for AirCross 2 device and connect. d.The App will automatically enter the firmware upgrade interface, please wait for the firmware download to complete, press the ‘upgrade’ button and wait for about 5 minutes. e.Restart the gimbal after the upgrade.
Note: The users manual is suitable for AirCross 2 V0.1.19 firmware.
