User Guide

ManualsBrandsMPC ManualsAnti-TheftMPC 2380 Factory Fob Activated Remote Start Kit for Select Ford & Lincoln Vehicles [2011-2016]. Includes a T-Harness To Simplify Installation. All firmware preloaded – no extra parts needed

1 | P a g e

TIP SHEET

(EVO-FORT1) 80-bit Add-On Stand-Alone Remote Starter T2380

*AUTOMATIC TRANSMISSION VEHICLES ONLY*

PREPPING HARNESS VIDEO: https://www.youtube.com/watch?v=FaVdjN2gsXs

INSTALL VIDEO: https://www.youtube.com/watch?v=9Bp7ncNGGyA

-The EVO-ALL interface module eliminates the need for a separate remote start module by using the

vehicle computer to start. It will monitor the vehicle lock circuit and use the pulses generated by

pressing lock 3 times on your OEM remote to start the vehicle.

-There are a LOT of wires in your kit, you will use very few of them. There will only be 3 connections

to make between the EVO-ALL and the FORT1 “T” harness. There will only be 2 required

connections made to your vehicle wiring.

-Parking light connection is an additional option. This will require a standard SPDT relay which is not

included with your kit. Refer to module guide for parking light wiring info. Supply power for relay must

connect directly to battery.

STEP 1: Starting the installation

-The bulk of the installation takes place right under the dash on the driver’s side. Begin by removing

the steering column shroud. It should be held on by 3 screws as located in the picture below. Be

careful not to break the panel – especially in cold weather.

Summary of content (9 pages)

PAGE 1
TIP SHEET (EVO-FORT1) 80-bit Add-On Stand-Alone Remote Starter T2380 *AUTOMATIC TRANSMISSION VEHICLES ONLY* PREPPING HARNESS VIDEO: https://www.youtube.com/watch?v=FaVdjN2gsXs INSTALL VIDEO: https://www.youtube.com/watch?v=9Bp7ncNGGyA -The EVO-ALL interface module eliminates the need for a separate remote start module by using the vehicle computer to start. It will monitor the vehicle lock circuit and use the pulses generated by pressing lock 3 times on your OEM remote to start the vehicle.
PAGE 2
|Page
PAGE 3
|Page
PAGE 4
EVO ALL Connections Locate the needed wires in the plugs of the vehicle as shown in the diagram, and connect the corresponding wires from the EVO-ALL to their respective locations. Cross reference the pin locations in each plug, and wire colors to verify you are on the right wires in the vehicle. There are 3 connections to make. Match the wires from the T harness up with the 20 pin harness colors as listed below. 1.
PAGE 5
Tip #2 – How to make your wiring connections It’s very important that all your wiring connections be solid and secure. All remote start connections are “tap on” connections. This means that you do not need to cut the wires in the car. You simply need to “tap on” to the wires in the car to make your connections. Do NOT use any kind of wire connectors such as “t” taps or scotch locks for the data connections in your vehicle; this must be a “wire touching wire” connection.
PAGE 6
2. Hood Pin - Most vehicles come with a factory equipped hood pin switch. If yours does not come with one you can wire in the aftermarket switch we supplied to the EVO ALL. You will need to mount the pin switch into metal. Then route the wire to the EVO ALL and connect to the Dark Blue wire on the 20 pin harness. You will need to open the loom up to access this wire. 3. Valet Switch – Your remote start kit includes a valet switch.
PAGE 7
  Mount the valet switch in the vehicle (Requires a small screw hole. Usually put in the driver’s kick panel (that’s the area forward of the door), the driver’s side of the center console, or the underside of the dash.) Connect one wire from the valet switch to the dark blue wire (pin A8) from the EVOALL 20 pin connector > and connect the second wire from the valet switch to ground. 4.
PAGE 8
STEP 4: Finish up! -Test all functions. The remote start will engage when you press the ‘lock’ button on your OEM key fob 3 times in a row.
PAGE 9
confirming that everything works properly, cap off or tape the ends of any wires you’re not using to avoid shorting. -Now gather up all the wiring and neatly bundle it together using zip ties or electrical tape to prevent the wires from interfering with any of the moving parts under the dash. -Find a secure place to put the remote start module and use zip ties to secure it.