Installation Guide
Path Light Features:
Motion/Light Sensor: The Path Light instantly turns on when it detects
motion from up to 15 feet away. The light sensor conserves battery life by
preventing the light from activating in daylight.
Auto Shut-o: Path Light shuts o automatically after 20 seconds if no
motion is detected.
Bright LED: 35 lumens cover up to 120 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant
material allow the light to work in all weather conditions.
GlowMode™ Option: Emits soft glow when darkness is sensed for safety.
600 Beta Drive, Unit 100, Mayeld Village, OH 44143
877.298.9082
Installation Instructions
NetBright
®
Path Light
MBN580
• 1 Screwdrive (athead)
• 1 Screwdriver (phillips)
• 1 Drill (6mm drill bit)
• 3 C-cell Alkaline Batteries (per light)
• 2 Screws & 2 Anchors
• 1 Stake & 1 Bracket
LED Light
Stake
Bracket
Motion & Light
Sensor
NOTE: Light sensor allows light to activate only in darkness. We recommend you test in a dark room or closet.
What you need to install:
Thank you for purchasing the Mr Beams
®
NetBright
®
Path Light. We are committed to
eliminating darkness using the latest in Light-
Emitting Diodes (LEDs). LEDs are the most
ecient and durable light sources available. We
are certain that your light will contribute to a safer
environment and provide light where you need it at
a very reasonable cost.
What is included per light:
www.mrbeams.com
Tips:
•
Use only new alkaline C-Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction.
•
Install batteries with polarity in correct position.
•
Light may activate when batteries are inserted. Simply take light into a dark room, allow
batteries to settle, then test activation.
•
If your light will not turn o, it means that it is time to replace the batteries.
1. Remove rear cover of
Path Light by removing 2
screws on back.
2. Set “GLOW” to ON to activate GlowMode™
feature. Setting “GLOW” to OFF will extend
battery life.
1. Determine location for mounting light. Flip rear
cover upside down and use holes for thumbscrews as
template to mark two holes for anchors and/or screws
(included). We recommend mounting the screws
parallel to the ground if mounting on a vertical surface.
Make sure that screws are precise distance from each
other as dened by the distance of the thumbscrew
holes. Replace rear cover and thumbscrews.
2. If using anchors, use 3/16” drill bit to drill holes
and insert anchors. Drive screws into anchors so
that screw head protrudes 1/8” from the surface.
If using only screws, us 1/8” drill bit to drill holes.
3. Slide light down so screws are securely held
by track.
4. Gently hammer stake
into desired location with
a hammer or mallet.
3. Insert 3 C-cell batteries
into light. Replace cover.
5. Insert Path Light into
mounting bracket.
6. Insert mounting
bracket into stake.
Mounting with Stake
Mounting on Wall
* 1 year limited warranty. Visit site for details.
* Visit our website to view installation video.
Battery Caution:
1) Do not mix old and new batteries
2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium
or Nickel Metal Hydride) batteries
3) Do not dispose of batteries in re
4) Batteries should be recycled or disposed of as per state and local guidelines
Setting up Lights to a Network
After inserting the batteries, choose a group
or channel for your lights with the dipswitches
next to the battery compartment. Ensure all
units are on the same channel by matching
dipswitches.
* Lights set to the same group that are
within 150 ft range of each other will work
together automatically