OPERATING INSTRUCTIONSAND OWNER’S MANUAL Model # KEROSENE FORCED-AIR HEATER MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
WARNING: WARNING: YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS, SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU OPERATE THIS HEATER. NOT FOR HOME OR RECREATIONAL VEHICLE USE WARNING: GENERAL HAZARD WARNING: FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.
SPECIFICATIONS CAUTION: CSA certified for use with only No. 1-K kerosene fuel. Factory Tested: Kerosene, Diesel #1 and #2, Fuel Oil #1 and #2, JP8 (Jet A Fuel) Model Burn Rate: Fuel Rate: Electrical Input: Line Protection: Min. Operating Voltage: Pressure Setting: Max. Outlet Temperature: Fuel Tank Capacity: Ignition: Spark Generator: Primary Safety Control: Certification: 50KR 50,000 Btu/hr (14.7 kW) 0.37 gal/hr (1.4 L/hr) 115V, 60Hz, 3.5a 10 amps 110V 3.5 psig (24 kPa) 1450oF (787oC) 4 gallons (15.
3. 4. 5. 6. 7. 8. Slide the large washer, then wheel onto the axle next to the cotter pin. Slide the spacer onto the axle next to the wheel. Slide the partially assembled axle through the wheel support frame. Slide the spacer onto the axle next to the wheel support. Slide the wheel then large washer onto the axle and hold in place with the remaining cotter pin. Install the caps over the larger washers to finish the wheel assembly.
Turn adjustment screw clockwise to increase pump pressure. Problem: Flame extends beyond the end of the heater. during cleaning, be sure all connections are tight before operating unit. STORAGE Store the heater in a dry location free from fumes or dust. At the end of each heating season, clean the heater as described in the MAINTENANCE section. Drain and flush the fuel tank with clean fuel.
DIAGNOSTIC SAFETY SHUTDOWN AND TROUBLE SHOOTING Model MH125KTR, MH175KTR and MH210KTR heaters are equipped with a diagnostic control board and flashing LED error indicator. This flashing LED signals indicate unit operation status. See the following diagnostic guide for unit status and corrective action if necessary. LED UNIT OPERATION TROUBLE SHOOTING Steady ON System Check System performing self test. No action required. Steady OFF Operation OK No action required.
WIRING DIAGRAM 18AWG GRN 1 18AWG WHT 18AWG YELL 2 3 MH50KR/MH75KTR HI-LIMIT SWITCH ON/OFF SWITCH 18AWG BLK 18AWG YELL THERMOSTAT 18AWG BLUE CAD CELL 18AWG BLK 18AWG WHT CORD SET 75KT,125KT,175KT,210KT ONLY 18AWG GRN H1 H2 FLAME CONTROL SCHEMATIC (connections may not be in same position on circuit board) 125KT,175KT, 210KT ONLY M1 18AWG PURPLE 17AWG BLK I2 I1 M2 18AWG PURPLE COM1 AC OUTLET ELECTR0DE 17AWG BLK L N 18AWG ORG 18AWG ORG MOTOR 18AWG PINK MOTOR CAPACITOR 18AWG PINK
PARTS LIST Ref.
Kerosene Forced Air Heater • Model MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR 22 27 23 9 35 28 50 25 18 21 26 51 43 53 Filter Kit 52 12 11 3 32 42 41 37 24 39 17 4 36 7 31 5 40 13 15 20 10 19 29 30 38 47 33 34 49 8 16 1 14 2 45 44 48 46 Mr. Heater, Inc.
OPERATING INSTRUCTIONS AND OWNER’S MANUAL Model # MH50KR, MH75KTR, MH125KTR, MH175TR, MH210KTR WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY. PARTS ORDERING INFORMATION: PURCHASING: Accessories may be purchased at any Mr.
GUIDE D'UTILISATION ET INSTRUCTIONS DE FONCTIONNEMENT APPAREIL DE CHAUFFAGE À AIR PULSÉ AU KÉROSÈNE Modèle # MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR LISEZ SOIGNEUSEMENT LES INSTRUCTIONS. Lisez et observez toutes les instructions. Conservez les instructions pour vous y référer ultérieurement. Interdisez à quiconque n'ayant pas lu les présentes instructions d'assembler, d'allumer, de régler ou de faire fonctionner cet appareil de chauffage.
AVERTISSEMENT : AVERTISSEMENT : NON CONÇU POUR ÊTRE UTILISÉ DANS UNE HABITATION OU UN VÉHICULE RÉCRÉATIF. VOTRE SÉCURITÉ PERSONNELLE ÉTANT IMPORTANTE POUR TOUS, VEUILLEZ LIRE LES INSTRUCTIONS AVANT D'UTILISER CET APPAREIL DE CHAUFFAGE. AVERTISSEMENT : DANGER D'INCENDIE, D'EXPLOSION ET D'INHALATION. CONSERVEZ LES MATÉRIAUX COMBUSTIBLES TELS QUE LES MATÉRIAUX DE CONSTRUCTION, LE PAPIER ET LE CARTON À UNE DISTANCE SÉCURITAIRE DE L'APPAREIL DE CHAUFFAGE COMME LE RECOMMANDENT LES INSTRUCTIONS.
SPÉCIFICATIONS PRUDENCE : CSA certifié pour l’utilisation avec seulement No. 1-K le combustible de pétrole. L’usine évaluée: No.2-K, No. 1 ou le gazole de No. 2, No. 1 ou le fuel de No. 2 ou le Jet de JP8 Modèles Taux de combustion : Consommation de combustible : Consommation électrique : Courant maximal : Temp. minimale de fonctionnement : Pression : Température de sortie maximale : Capacité du réservoir : Allumage : Générateur d'étincelle : Appareil de commande : Certification : MH50KR 50 000 Btu/h (14.
3. Vérifiez soigneusement tout dommage qu'aurait pu subir l'appareil de chauffage pendant l'expédition. Si vous constatez quelque dommage, avisez immédiatement le fabricant au 1 800 251-0001. ASSEMBLAGE (Pour modèles de 125 000, 175 000 et 210 000 BTU/h uniquement, voir la figure 1, page 8.) Les roues et les poignées se trouvent dans la boîte avec les pièces servant à l'assemblage. Les roues, l'essieu et les pièces servant à l'assemblage se trouvent dans un emballage.
combustion doit être rouge cerise sans présenter de taches foncées, et la flamme ne doit pas se prolonger au-delà du cône. SYMPTÔMES DE RÉGLAGE DE PRESSION INCORRECT Problème : L'appareil ne produit pas une flamme forte et homogène. L'appareil émet de la fumée et éjecte du combustible brut. Le cône avant ne devient pas rouge cerise. 2. Cause : La pression est trop faible. Serrez la vis de réglage pour augmenter la pression de la pompe. Problème : La flamme dépasse l'extrémité du tube de sortie.
DIAGNOSTIC ET DÉPANNAGE APRÈS UN ARRÊT D'URGENCE Ces instructions s'appliquent aux modèles MH125KTR, MH175KTR et MH210KTR. Utilisez le guide de dépannage suivant pour diagnostiquer et corriger les problèmes. VOYANT CAUSE SOLUTION 1 clignotement Verrouillage du système 1) Assurez-vous que l'appareil est refroidi, appuyez sur le bouton de réinitialisation et essayez de nouveau.
SCHÉMA DE CÂBLAGE INTERRUPTEUR MARCHE-ARRÊT VRT AWG 18 NOIR AWG 18 1 BLC AWG 18 INTERRUPTEUR COMMANDE MAX.
LISTE DES PIÈCES Réf.
Appareil de chauffage à air pulsé au kérosène • Modèles MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR 22 27 23 9 35 28 50 25 18 21 26 51 43 53 Kit de Filtre à Carburant 52 12 11 Filtre à carburant 3 32 42 41 37 24 39 17 4 36 7 31 5 40 13 15 20 10 19 29 30 38 47 33 34 49 8 16 1 14 2 45 44 48 46 Mr. Heater, Inc.
GUIDE D'UTILISATION ET INSTRUCTIONS DE FONCTIONNEMENT Modèle # MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR AVERTISSEMENT : N'UTILISEZ QUE LES PIÈCES DE RECHANGE DU FABRICANT. L'UTILISATION D'AUTRES PIÈCES RISQUE DE CAUSER DES BLESSURES ET LA MORT. LES PIÈCES DE REMPLACEMENT NE SONT OFFERTES QUE PAR LE FABRICANT ET DOIVENT ÊTRE INSTALLÉES PAR UNE ENTREPRISE SPÉCIALISÉE. INFORMATIONS SUR LA COMMANDE DE PIÈCES : ACHAT : On peut se procurer des accessoires auprès de tous les détaillants locaux Mr.
INSTRUCCIONES DE USO Y MANUAL DEL USUARIO CALENTADOR DE CALDEO A AIRE FORZADO A KEROSENE Modelos # MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR LEA CUIDADOSAMENTE LAS INSTRUCCIONES: lea y siga todas las instrucciones. Conserve estas instrucciones en un lugar seguro para futura referencia. No permita que nadie que no haya leído estas instrucciones arme, encienda, ajuste o use el calentador.
ADVERTENCIA: ADVERTENCIA: NO APTO PARA USAR EN EL HOGAR NI EN CASAS RODANTES. SU SEGURIDAD ES IMPORTANTE PARA USTED Y PARA LOS DEMÁS, ASÍ QUE POR FAVOR LEA ESTAS INSTRUCCIONES ANTES DE UTILIZAR EL CALENTADOR. ADVERTENCIA: ADVERTENCIA GENERAL DE PELIGRO: PELIGRO DE INCENDIO, QUEMADURAS, INHALACIÓN Y EXPLOSIÓN. MANTENGA LOS COMBUSTIBLES SÓLIDOS, TALES COMO MATERIALES DE CONSTRUCCIÓN, PAPEL O CARTÓN, A UNA DISTANCIA SEGURA DEL CALENTADOR.
ESPECIFICACIONES CUIDADO: certificación por CSA para uso únicamente con el combustible a base de kerosene n.° 1-K. Probado en fábrica para utilizarlo con el kerosene N.º 2-K, diesel N.º 1 o N.º 2, fueloil N.º 1 o N.º 2 o combustible JP8 Jet A Modelo 50KR 75KTR 125KTR 175KTR 210KTR Tasa de combustión: 50,000 Btu/h (14.7 kW) 75,000 Btu/h (22 kW) 125,000 Btu/h (37 kW) 175,000 Btu/h (51 kW) 210,000 Btu/h (61.5 kW) Tasa de combustible: 0.37 gal/h (1.4 L/h) 0.55 gal/h (2.1 L/h) 0.96 gal/h (3.
INSTRUCCIONES DE OPERACIÓN V, 60 Hz, 1 Ø. Gire el termostato al ajuste más alto. Para encender el calentador, coloque el interruptor en la posición “On” (la luz significa que el interruptor se encuentra en la posición “ON”). Ajuste el termostato en el valor deseado. El calentador se prende y apaga según se necesite o no calor. REQUISITOS DEL CABLE DE EXTENSIÓN: hasta 100’ (30.5 m) use un conductor de calibre 16 awg. 101’ - 200’ (30.5 61.0 m) use un conductor de calibre 14 awg.
PROCEDIMIENTO DE AJUSTE: 1. Llene el tanque de combustible. 2. Encienda el calentador. 3. Ubique el tornillo de ajuste de presión de combustible (ref. n.° 29) en el diagrama extendido de piezas. El tornillo de ajuste de presión se encuentra en la parte posterior del calentador, en la tapa de la cubierta del filtro de aire (aprox. a 2” del lado izquierdo y a 1” de la parte superior). Quite y deseche la tapa de goma (ref. n.° 4) para dejar expuesto el tornillo. 4.
APAGADO DE SEGURIDAD DE DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS Los calentadores modelos MH125KTR, MH175KTR y MH210KTR están equipados con una placa de control de diagnóstico y un indicador de error con LED parpadeante. Estas señales LED parpadeantes indican el estado de funcionamiento de la unidad. Consulte la siguiente guía de diagnóstico para ver el estado de la unidad y la acción correctiva, si fuera necesaria.
DIAGRAMA DE CABLEADO 18 AWG VERDE 1 18 AWG BLANCO MH50KR/MH75KTR INTERRUPTOR LIMITADOR MÁXIMO LLAVE DE ENCENDIDO 18 AWG NEGRO 18 AWG AMARILLO 2 3 18 AWG AMARILLO 18 AWG NEGRO 18 AWG AZUL CÉLULA DEL CAD TERMOSTATO 75KT, 125KT, 175KT, 210KT ÚNICAMENTE H1 H2 TOMACORRIENTE DE CA DIAGRAMA DE CONTROL TIC DE LA LLAMA (las conexiones pueden no estar en la misma posición en la placa de circuito) 125KT, 175KT, 210KT ÚNICAMENTE M1 18 AWG PÚRPURA 17 AWG NEGRO I2 I1 L N 18 AWG NARANJA 18 AWG NARAN
LISTA DE PIEZAS Ref. Artículo # Artículo # Artículo # Artículo # Artículo # Descripción Ref.
Calentador de queroseno a aire forzado • Modelos MH50K, MH75KT, MH125KT, MH175KT, MH210KT 22 27 23 9 35 28 50 25 18 21 26 51 43 53 Kit Filtre à Carburant 52 12 11 Filtre à carburant 3 32 42 41 37 24 39 17 4 36 7 31 5 40 13 15 20 10 19 29 30 38 47 33 34 49 8 16 1 14 2 45 44 48 46 Mr. Heater, Inc.
INSTRUCCIONES DE USO Y MANUAL DEL USUARIO Modelos # MH50KR, MH75KTR, MH125KTR, MH175KTR, MH210KTR ADVERTENCIA: USE SOLAMENTE PIEZAS DE REEMPLAZO DEL FABRICANTE. EL USO DE CUALQUIER OTRA PIEZA PODRÍA CAUSAR HERIDAS O LA MUERTE. LAS PIEZAS DE REEMPLAZO ESTÁN DISPONIBLES ÚNICAMENTE EN LA FÁBRICA Y DEBEN SER INSTALADAS POR UNA AGENCIA DE SERVICIO CALIFICADA. INFORMACIÓN PARA PEDIR PIEZAS: COMPRAS: los accesorios se pueden comprar en cualquiera de los distribuidores locales de Mr.