OUTDOOR HD BULLET IP CAMERA PRODUCT MANUAL GB - NL
GB PARTS & FUNCTIONS ------------ 1. 6. -----------4. 1. 2. 3. 4. 5. 6. ---------- 3. ---------------- ------------ 7. ---------------- 5. 2. ---------------- Outdoor IP camera unit Antenna Mounting bracket Network connection Power connection Power adapter GETTING STARTED • • The mrSafe Outdoor IP camera has many connections. When the mrSafe camera can be installed within the range of your Internet modem, you only need to provide a power supply.
- The warts are placed around the cables. You may need to cut the wartel around the camera cable. If so, it needs to be sealed again later. There are 2 connections open at the bottom of the cable box. - The cables are entered into the box and positioned so there isn’t any tension on the connection or the cable. If you need to cut the box to enter the camera cable, this must be subsequently sealed. - The power cable of the adapter will be temporarily removed from the terminal box.
- A hole of about 10 mm will be drilled through the wall. The round plug of the power cable will be taken from the inside to the outside. The cable box is placed close to the power cable. The round plug will be attached to the camera cable inside the cable box. - The hole in the wall, the warts and possible cuts in the cable box should be sealed so that everything is water resistant. - If you want, you can fix the cable as well.
PLACING THE MICRO SD CARD Important: The SD card should be a Class 10 SD card with a maximum capacity of 32 GB ! • Turn off the Outdoor IP Camera. • Use a long cross-screwdriver to remove the 3 cross-screws that connect the plastic to the metal as well. • Insert the micro SD card. • • Close the housing. Power ON the Outdoor IP Camera.
NL ONDERDELEN EN FUNCTIES ------------ 1. ---------- 5. ---------------- ------------ ------------ 2. 3. 6. ---------------- 4. 1. 2. 3. 4. 5. 6. Outdoor IP camera Antenne Montagebeugel Netwerkaansluiting Stroomaansluiting Voedingsadapter AAN DE SLAG • • De MrSafe Outdoor camera heeft vele aansluitingen. Als de MrSafe Outdoor camera binnen het Wifi bereik van uw internet modem geplaatst kan worden, dan hoeft u alleen maar een stroomvoorziening te verzorgen.
- We gebruiken een kabeldoos die voor een paar euro bij de bouwmarkt verkrijgbaar is. De wartels worden rond de kabels geplaatst. Mogelijk dient u de wartel rond de camerakabel in te snijden, deze moet dan later wel afgedicht worden. In de kabeldoos worden 2 aansluitingen aan de onderzijde geopend. - De kabels worden in de doos ingevoerd, en zo geplaatst dat het past zonder dat er spanning op een verbinding of kabel staat.
- Er wordt een gat van ca. 10 mm door de muur geboord. Van binnenuit wordt de ronde stekker van de voedingskabel naar buiten gevoerd. De kabeldoos wordt dicht bij deze voedingskabel geplaatst. De ronde stekker wordt in de kabeldoos aangesloten op de kabel van de camera. - Het gat in de muur, de wartels en een eventuele insnijding in de kabeldoos dienen met kit waterdicht afgewerkt te worden. - Eventueel zet u de kabel nog vast. De adapter wordt nu in het stopcontact gestoken en de installatie werkt .
DE MICRO SD-KAART PLAATSEN Belangrijk: De SD-kaart moet een Class 10 SD-kaart met een maximale capaciteit van 32 GB zijn! 1. Schakel de IP Camera uit. 2. Draai de 3 kruiskopschroeven die de plastic verbinden met het metaal ook los. 3. Plaats de Micro SD kaart. 4. Sluit de behuizing. 5. Schakel de IP Camera in.