Installation, Operation & Maintenance Manual ™ ™ iTEMPO & iTEMPOPLUS CONTROLS mr.steam ® Feel Good Inc. www.mrsteam.
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS 2. ! WARNING Do not permit children under the age of 16 to use this steambath. 3. ! WARNING Steam is hot and can cause injury or death if improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room. 4.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® REA D ME F IR S T ! Table of Contents: ! WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and operation of this generator. These are types of potential hazards that may occur during installation and operation: Important Safety Instructions...............................
mr Installation & Operating Instructions .steam ______________________________________________________________ ® BEFORE INSTALLING Carefully inspect the control and packaging for shipping damage. In the event of shipping damage, please contact the carrier for claim information. Our customer service department can assist you with any missing or damaged parts. per instructions for the Remote Temperature Probe.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Dimensional Information for the Round and Square iTempo™ and iTempoPlus™ Box Contents: • iTempo™ or iTempoPlus™ Control • Control Cable (30 ft.) • Steam head • Tube of Silicone Sealant • Owner’s Manual 41/2” 1” 3/8” 21/2” 5” 1/4” 5” 3/ ” 33/ ” 4 4 12” long pigtail 5 Drawings for Illustrative Purposes Only.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Installation Instructions for Round & Square iTempo™ and iTempoPlus™ 2-5⁄8” Step 1 Determine the desired installation location of the control. The iTempo™ and iTempoPlus™ controls are designed to be installed inside or outside the steam room as a matter of personal preference.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® NOTE: The connector is keyed with the flat facing up. The control cable is the same at both ends. important NOTE: Be careful not to strain, staple, pinch or otherwise damage the control cable. Route cable as required to permit replacement. Do not route cable inside conduit together with power lines or close to hot water or steam piping.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Step 6 Diagram 5 Run a bead of silicone (provided) as shown to the outer edge of the control faceplate, following the contour of the circle or square shape. Use silicone as required to create a moisture seal. Note: The silicone supplied by Mr. Steam can be used to meet a variety of sealing and gasketing.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Installing the Remote Temperature Probe (PN: MSTS) The Remote Temperature Probe is required when the iTempo or TempoPlus Controls are installed outside the steam room. d. The probe has an integral 30’ cable. Insure that the probe and/or steam generator are located accordingly. 2. Drill a 5/16 inch diameter hole in the wall. Do not oversize or under size the hole. Clean area thoroughly.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Temperature Probe Connection Diagram 1 Knock-Out Temperature Probe Cable (30 feet) Mr.Steam Steam Generator Temperature Sensor Probe (shown with cover removed and NOT installed) 10 Drawings for Illustrative Purposes Only.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® steam room interior 5. Route the end of the probe cable with the temperature probe through the wall into the steam room as shown in Diagram 2. DIAGRAM 2 important note: Do not strain, staple, pinch or otherwise damage the probe cable. 6. With a minimal length of the cable exposed apply silicone (provided) to the hole in the wall as required to create a moisture seal as shown in Diagram 2.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® iTempo™ Operating Instructions The iTempo Control features programmable digital temperature control, a fixed (60) minute duration, ON/OFF and PAUSE.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Timer Feature When the control is turned ON a 60 minute time duration is initiated. The control will turn off after 60 minutes unless the control is turned off manually. Memory Feature If the control is turned off manually before 60 minutes then the default temperature of 110˚F will be used the next time the control is turned on.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® iTempoPlus™ Operating Instructions The iTempoPlus Control features programmable temperature control, programmable time duration, clock, AromaSteam, ChromaSteam®, ON/OFF and two personal settings.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Setting the Clock Diagram 3 When the display is not flashing: Press and hold the TIME key until the display starts flashing. Use the UP/DOWN keys to select the desired time, at this time the AM/PM logo will be displayed. Press the TIME key to save changes. Note: The clock can only be set when the generator is off.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Setting the Temperature Diagram 6: Press TEMP key to set the desired temperature or display the temperature setting. Diagram 7: The control is preset and will display a temperature setting of 110˚F (default setting). With the temperature displayed, press the UP or DOWN keys to set the desired temperature (80°F to 120°F) in one degree increments.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Changing the Temperature units (˚F/˚C) When the generator is Off, Press and hold ON/OFF key for 10 seconds. The temperature units will be displayed as Fahrenheit (TuF) or Celsius (TuC). Use the UP/DOWN keys to choose between (TuF) and (TuC). Press ON/OFF key to accept the new value and exit. aroma mr.
mr Installation & Operating Instructions .steam ______________________________________________________________ ® Display mr.steam Up Key Time Display/ Adjust Key ON/OFF Key temp time aroma chroma AromaSteam Key Time Display/ Adjust Key Down Key Program Key ChromaSteam Key Care Tips for all Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. Do not use abrasive cleansers 3.
mr.steam ® Feel Good Inc. Products, information and specifications are subject to change without notice. For more information call Sales & Support at: 1.800.76.STEAM (East Coast) 1.800.72.STEAM (West Coast) 2015 © Sussman-Automatic Corporation Mr.Steam and des., AromaFlo, AutoFlush, AutoSteam, Butler Package, ChromaSteam, Clean Steam...
