Installation Guide

ManualsBrandsMr. Steam ManualsBath7.5kW Steam Bath Generator with iTempo AutoFlush Square Package in Polished Chrome

CONTROL ROUGH IN

Refer to Installation Instructions for the specific control

IMPORTANT NOTE: The control cable should be run in a

dedicated 1” conduit to facilitate installation and service.

Determine the desired installation location of the con-

trol. The iSteam

AirTempo

iTempo

and iTempo/Plus

controls are designed to be installed inside or outside the

steam room as a matter of personal preference. If the con-

trol is in-stalled inside the steam room the control must be

located:

2. 4-5 feet above the floor near the bather seating area

3. The control features an integral temperature sensor.

Locate the control in a location representative of the

desired steambathing temperatures.DO NOT locate

the control above or near the steam head or direct

steam emissions.

4. on a vertical wall

The iSteam and iTempo control cable length is 30 feet.

Insure that the control and/or steam generator are locat-

ed accordingly. An optional 60 foot cable is available, PN

103990-60 for AirTempo and iTempo and PN 104117-60 for

iSteam. Contact a MrSteam technical service representative if

a 60 foot cable is required. Excess control cable should be

neatly coiled and twisted into a figure 8. The AirTempo dongle

is provided with a 3 foot cable. The maximum cable length is

60 feet.

IMPORTANT NOTES:

• If the control is installed outside the steam room a Remote

Temperature Probe Part Number MSTS or iMSTS must be

installed inside the steam room, depending on the control.

• Insure MrSteam steam generator is iSteam, AirTempo or

iTempo compatible and has a serial number 900000 or high-

er. If iSteam is used with a generator having serial number

900000 through 930030, contact MrSteam technical support

for an upgraded PC board.

•

See instructions for the MSTS or iMSTS Temperature Probe

(located in the Control Installation Manual related to your spe-

cific control package) before rough-in or installation of control.

steam

Installation, Operation & Maintenance Manual

__________________________________________________________________________

BEFORE INSTALLING

Turn power to the steam generator OFF before connecting the

control to the generator. Failure to turn the power off will result in

an inoperable control.

To avoid unintentional steambath operation,

DO NOT locate the control where other controls, acces-

sories, shower heads, valves, body sprays or similar within

the shower could cause confusion or interfere with the

MrSteam control’s intended use and function.

DO NOT use any iSteam

, AirTempo

iTempo/Plus

, iTempo

, HomeWizard

or iGenie

controls

without reading and understanding its own manual and the

MrSteam steam generator Installation and Operation Manual.

Failure to read and understand these instructions may result

in an inoperative or hazardous installation.

A peel and stick warning sticker must be read

and permanently affixed in a conspicuous location near the

steam room. Failure to read and affix this warning sticker in a

conspicuous location may result in serious injury or death. .

Install the iSteam, AirTempo, iTempo or iTempo/Plus controls

according to installation instructions. Failure to install accord-

ing to instructions will result in an inoperative control or haz-

ardous overheating or inadequate heating of the steam room.

If an iSteam, AirTempo, iTempo or iTempo/Plus control is

installed outside the steam room a Remote Temperature

Probe (PN MSTS or iMSTS) must be installed inside the

steam room per installation instructions supplied with the

Remote Temperature Probe. Failure to install according to

instructions will result in an inoperative control and overheat-

ing of the steam room.

CAUTION

WARNING

I N S T A L L E R

DO NOT route iSteam,

AirTempo,

iTempo/Plus,

iTempo, HomeWizard or iGenie control wiring inside conduit

together with power lines or close to hot water or steam piping.

Doing so may result in an inoperative or hazardous installation.

DO NOT alter or modify any MrSteam product. Doing so may

result in an inoperative or hazardous installation and will void the

UL listing and warranty.

IMPORTANT NOTES:

1. Turn power to the steam generator OFF before connect-

ing the control to the generator. Failure to turn the power

off will result in an inoperable control.

2. DO NOT operate iSteam, AirTempo,iTempo/Plus, iTempo,

HomeWizard or iGenie controls with other than a MrSteam

iSteam, AirTempo, or iTempo compatible steam generator.

MrSteam residential steam generators with serial numbers

lower than 900000, or any other brand of steam generator

are not to be operated with iTempo controls. Doing so

may result in an inoperative or hazardous installation. If

iSteam is used with a generator having serial number

900000 through 930030, contact MrSteam technical sup-

port for an upgraded PC board.

3. This document contains important safety, operation and

maintenance information. Leave this document with the

homeowner. Do not discard this document.

4. Discontinue use of the steam generator or control if the

steam generator is damaged or otherwise not functioning

properly. Operating a damaged steam generator may

result in an inoperative or hazardous installation

CONTROL INSTALLATION

Refer to Control Manual for specific installation requirements