Generator Installation Sheet

ManualsBrandsMr. Steam ManualsBath9kW Steam Bath Generator with iSteam3 AutoFlush Package in Black

LOCATING THE STEAM GENERATOR

Select a location as near as practical to the steam room.

Typical locations include: closet, vanity cabinet, heated attic or basement.

NOTE:

The standard length of the cable for connecting the control to the steam generator is 30 feet. The steam generator and

control must be located accordingly. A 60 foot cable is available as a special order part for iTempo

and AirTempo

, PN 103990-

60 and PN 104117-60 for iSteam

The maximum cable length is 60 feet.

IMPORTANT NOTE: The control cable should be run in a dedicated 1" conduit to facilitate installation and service.

DO NOT route iSteam, AirTempo, iTempo/Plus, iTempo, HomeWizard or iGenie control wiring inside conduit

together with power lines or close to hot water or steam piping. Doing so may result in an inoperative or hazardous installation.

(Items 1-4)

1. DO NOT

install steambath generator inside steam

room, a shock hazard will occur

2. DO NOT

install steambath generator outdoors or

wherever environmental conditions may result in a

shock hazard or affect performance of the generator.

3. To prevent damage to the steam generator or a fire

hazard DO NOT

install steambath generator near

flammable or corrosive materials or chemicals such as

gasoline, paint thinners, or the like. Installation in areas

having high concentrations of chlorine (such as pool

equipment room) must be avoided.

4. Burn Hazard. Steam line, safety valve, drain valve and

plumbing become hot during operation and remain

hot after shutdown for a period of time. Provide

appropriate protection, including insulating plumbing

lines. Avoid plumbing runs and steamhead locations

that can come in contact with bathers.

(Items 5-7)

5. DO NOT

install steambath generator or plumbing lines

in unheated attic or any locations where water could

freeze and cause pipes to rupture and cause property

damage.

6. Install steambath generator on a solid and level

surface. Keyhole slots are provided for wall mounting.

Insure the steam generator is properly secured and level

when mounting with keyhole slots to prevent damage to

the steam generator.

7. Install steambath generator in an upright position only

to prevent damage to the generator.

IMPORTANT NOTES: (Items 8-12)

8. Install anti-water hammer device as necessary.

Provide a minimum of (12) inches at both ends and top of

the steam generator or as required for servicing. See page 8.

10.

Provide unions as required to facilitate installation

and disconnection of piping.

. MrSteam controls can be located inside the steam room

or on the outside of the steam room. See the Control

Installation Manual for your specific control package for

specific details.

12. The MS series of steam generators are for residential

use only. Commercial or other nonresidential applications

void the warranty and may adversely affect product

performance and may represent a safety hazard.

NOTE:

MrSteam Generators (inclusive of the iTempo, AirTempo

and iSteam series Controls) are CE and UL listed.

Suitable for operation in ambient not

exceeding 45 °C (113˚ F)

WATER QUALITY INFORMATION

For optimum results, the water supply should be tested prior

o installation. If the mineral content exceeds the following

recommended limits, various external treatment processes

are recommended to correct the problem.

NOTE: An analysis of the on-site water must be made by

a recognized and reliable water treatment company to

ascertain the existing condition and treatment required.

Poor water quality can affect efficiency or result in steam gen-

erator damage. Water contains impurities in solution and sus-

pension. These impurities concentrate in the generator. The

concentration of these impurities increases as more feedwater

is introduced into the generator and steam is produced. If the

suspended solids are allowed to concentrate beyond certain

limits, a deposit or “scale” will form on the generator internal

surfaces. This deposit can interfere with the proper generator

operation and cause generator failure. The concentration of

these impurities is generally controlled by the water quality

and by periodic draining of the generator.

RECOMMENDED FEEDWATER QUALITY

Hardness, ppm 8 – 85 (~0.5 – 5 gpg)

P-Alkalinity, ppm 85 – 410 (~5 – 24 gpg)

T. Alkalinity, ppm 200 – 500 (~7 – 0 gpg)

pH (strength of alkalinity) 8.0 – 11.4

Every 2 months, or more often in “hard” water areas,

the manual drain valve should be opened fully flushing

out accumulated materials, salts and other particles

which are natural by-products of boiling water.

The optional AutoFlush System feature automatically

drains the MrSteam

generator following each use.

A time delay allows the water to cool down (about

two hours) before it drains by gravity for a safe and

gentle operation.

WARNINGS

CAUTIONS

I N S T A L L E R

steam

Installation, Operation & Maintenance Manual

__________________________________________________________________________

WARNING