Specification

ManualsBrandsMr. Steam ManualsBath9kW Steam Bath Generator with iSteam3 AutoFlush Package in Black

(368)

(64)

"(130)

(45)

(171)

" (45)

(127)

(162)

/8"(48)

(130)

(210)

(375)

(302)

Water Inlet

Control & Acces-

sory Connections

Steam Outlet

Safety Valve

Manual Drain Valve

Optional

AutoFlush

steam

Sussman-Automatic Corp

hello@mrsteam.com www.mrsteam.com

43-20 34th Street, Long Island City, NY 11101 TEL: 800 76 STEAM / 9410 S. La Cienega Blvd. Inglewood CA 90301 TEL:800 72 STEAM

Mr.Steam Standard Features

• Stainless steel tank

• Industrial, large diameter,

serviceable heating element

• Modular Plug and Play connections

• Electronic water-level control system

• Full-port drain valve

• Limited lifetime generator parts warranty

Safety Features

• Built-in, low-voltage 24-volt control

• ASME safety valve

Locating and Installing the Steam Generator Unit

• Select a location as near as practical

to the steam room, within 60 feet.

Typical locations include: closet, van-

ity cabinet, heated attic or basement.

• Do not install steambath generator

inside the steam room.

• Do not install steambath generator

outdoors or wherever environmental

conditions may affect the safety and/

or performance of the generator.

• Do not install steambath generator or

plumbing lines in unheated attic or

any locations where water could

freeze.

• Do not install steambath generator

near flammable or corrosive materials

Required Plumbing

Steam Outlet (1/2" NPT) Drain (1/2" NPT)

Water Supply (3/8" NPT) Safety Valve (3/4" NPT)

Steam Head (1/2" NPT)

Electrical

All electrical wiring to be installed by a qualified

licensed electrician in accordance with National

Electrical Code and local electrical code.

Power Wiring

1. Check power voltage. Use 240V rated unit when

supply matches rating of unit before installation.

2. Use minimum 90˚ C/300V rated insulated copper

conductors only, type THHN or equal sized in

accordance with National Electrical Code and local

electrical code for the Amps in Ampere Chart.

If allowed by code, NM cable may require a larger

wire size than as listed on the chart.

3. Connect suitably sized equipment grounding wire to

ground terminal provided.

4. Install a separate circuit breaker between supply and

unit. Provide a power supply disconnect within

sight of the steam generator or one that is capable

of being locked in the open position.

A M P E R E C H A R T

Max Room Volts Wire Size

Model no. Vol. cu.ft. KW 1 ph Phase Amps (AWG)

MS90E 100 5

208 1 24 10

240 1 21 10

MS150E 150 6

208 1 29 8

240 1 25 8

MS225E 225 7.5

208 1 36 8

240 1 32 8

MS400E 360 9

208 1 44 8

240 1 38 8

MODEL VOLTAGE* PHASE OPTIONS PROJECT INFORMATION



B=208



1-Single Phase



Express



C=240



3-Three Phase

Steam

Contact Mr. Steam for other voltages

Notes:

Location:

Architect:

Engineer:

Contractor:

Submitted By:

Date:

Required Equipment: Required Equipment:

iSteam3, AirTempo, iTempo, iTempoPlus Controls

Optional Equipment: iGenie, AudioWizard, ChromaSteam, HomeWizard, Recessed

Light, MS Light, MS Wallseat, AutoFlush, Condensation Pan, AromaSteam

or chemicals or in areas having a high

concentration of chlorine.

• Install steambath generator on a solid

and level surface or securely mounted to

a wall using the keyhole slots provided.

• Install steambath generator in an upright

position only.

• Provide a minimum of 12 inches inches

at both ends and top of the steam

generator or as required for servicing.

Alternately provide unions to facilitate

installation and disconnection of the

steam generator.

• The minimum clearance from com-

bustible surfaces is zero all around.

FOR ILLUSTRATIVE PURPOSES ONLY. IMPORTANT NOTE: FOR

SAFE AND TROUBLE FREE INSTALLATION visit mrsteam.com before

installation to download the Installation, Operation and Maintenance

Manual or refer to the manual provided with the unit.

TS0041-90E-400E REV 2.1.19

steam

Technical Specifications

______________________________________________________

Model MS90E-400E

Serial Number 900000 and higher

• 60-minute electronic countdown

shutdown with 75-minute limiting

safety back-up



MS90E



MS150E



MS225E



MS400E

Summary of content (4 pages)

PAGE 1
mr .steam ______________________________________________________ ® Technical Specifications 13/4" (45) Model MS90E-400E Serial Number 900000 and higher Water Inlet Mr.
PAGE 2
mr.steam ® Technical Specifications iSteam®3 Box Contents: • iSteam3 • Owner’s Manual • Control Cable (30 ft.) • Rough-In Box • Steamhead • Optional Surface • Tube of Silicone Sealant Mount Gasket Dimensional Information 13⁄8” 6 1⁄8” 10:06 AM 97 4 1⁄2” F 12:16 PM START START ACCESSORIES Pigtail (81⁄2”) SETTINGS Wall location for optional surface mount Wall location for flush mount iSteam controls flush mount in the steam/shower enclosure through a 5-1/4” wide x 3-9/16” high hole.
PAGE 3
mr.steam ® Technical Specifications AutoFlush ® AutoFlush Shown Fully Assembled Box Contents • AutoFlush Valve with Cord • Installation instructions Operation The optional AutoFlush System feature automatically drains the Mr.Steam® system following each use. A time delay allows the water to cool down (about two hours) before it drains by gravity for a safe and gentle operation.
PAGE 4
mr.steam ® Technical Specifications Round 103937, Square 104040, 104104 AromaSteam Steamhead 7/8” • Even distribution of steam while remaining cool to the touch • No field assembly required • No moving parts • Integrated aromatherapy oil well for in shower use 1” 3” 3” 3” 23/4” 03” 103937 Round & Square Steamhead Installation 104040 (1⁄2" NPT) IMPORTANT: Do not disassemble steamhead. MrSteam’s steam head is shipped fully assembled and requires no additional assembly.