Butler/Butler2/ ButlerX/Linear iTempo Plus Control AromaSteam SteamHead Linear SteamHead SteaLinx Mobile App MS / Super AutoFlush MX AutoFlush Condensation Pan PUR100474 PUR100421 PUR103936 PUR100518 PUR100200E PUR100532 TS0012 06-15 10-15 04-21 01-18 10-15 02-19 02-19 2021-07-16
Installation, Operation & Maintenance Manual ® ® iTEMPO & iTEMPOPLUS CONTROLS mr.steam ® Feel Good Inc. www.mrsteam.
2
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS 2. ! WARNING Supervise children at all times. 3. ! WARNING Steam is hot and can cause injury or death if improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room. 4.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® REA D ME F IR S T ! Table of Contents: ! WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and operation of this generator. These are types of potential hazards that may occur during installation and operation: Important Safety Instructions...............................
mr Installation & Operating Instructions .steam _________________________________________________________________ ® BEFORE INSTALLING Carefully inspect the control and packaging for shipping MrSteam technical service 1-800-767- 8326 for damage. In the event of shipping damage, please contact more information on the Remote Temperature the carrier for claim information. Our customer service de- Probe. partment can assist you with any missing or damaged parts.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Dimensional Information for the Round and Square iTempo and iTempoPlus ® ® 41/2” 1” 3/8” 21/2” 5” 1/4” Box Contents: • iTempo or iTempoPlus Control • Control Cable (30 ft.) • Steam head • Tube of Silicone sealant • Owner’s Manual 5” 3/ ” 33/ ” 4 4 12” long pigtail 6 Drawings for Illustrative Purposes Only.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Installation Instructions for Round & Square iTempo® and iTempoPlus® IMPORTANT NOTE: If the desired location for the control is outside the steam room a Remote Temperature Probe (MSTS) must be installed inside the steam room. Contact MrSteam technical service 1-800-7678326 for more information on the Remote Temperature Probe. NOTE: The connector is keyed with the flat facing up.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Step 2 Diagram 1 Make a 2-5⁄8” wide by 3-7⁄8” high cutout in the desired control location. Do not oversize or under size the cutout. tep 3 Diagram 2 S Route the control cable (provided with the control) from the wall cutout to the steam generator. Connect one end of the cable to the steam generator connector. Diagram 2 NOTE: The connector is keyed with the flat facing up.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Step 5 Diagram 4 Remove and discard peel-off paper to expose adhesive liner. Diagram 5 Step 6 Diagram 5 Run a bead of silicone (provided) as shown to the outer edge of the control faceplate, following the contour of the circle or square shape. Use silicone as required to create a moisture seal. Note: The silicone supplied by MrSteam can be used to meet a variety of sealing and gasketing.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® iTempo® Operating Instructions The iTempo Control features programmable digital temperature control, a fixed (60) minute duration, ON/OFF and PAUSE.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Timer Feature When the control is turned ON a 60 minute time duration is initiated. The control will turn off after 60 minutes unless the control is turned off manually. Memory Feature If the control is turned off manually before 60 minutes then the default temperature of 110˚F will be used the next time the control is turned on.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® iTempoPlus® Operating Instructions The iTempoPlus Control features programmable temperature control, programmable time duration, clock, AromaSteam, ChromaSteam®, ON/OFF and two personal settings.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Setting the Clock Diagram 3 When the display is not flashing: Press and hold the TIME key until the display starts flashing. Use the UP/DOWN keys to select the desired time, at this time the AM/PM logo will be displayed. Press the TIME key to save changes. Setting the steambath Duration Diagram 4 Press TIME key to set or display the steambath duration time on the clock.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Setting the Temperature Diagram 6: Press TEMP key to set the desired temperature or display the temperature setting. Diagram 7: The control is preset and will display a temperature setting of 110˚F (default setting). With the temperature displayed, press the UP or DOWN keys to set the desired temperature (80°F to 120°F) in one degree increments.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Changing the Temperature units (˚F/˚C) When the generator is Off, Press and hold ON/OFF key for 10 seconds. The temperature units will be displayed as Fahrenheit (TuF) or Celsius (TuC). Use the UP/DOWN keys to choose between (TuF) and (TuC). Press ON/OFF key to accept the new value and exit. aroma mr.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® Display mr.steam Up Key Time Display/ Adjust Key ON/OFF Key temp time aroma chroma AromaSteam Key Time Display/ Adjust Key Down Key Program Key ChromaSteam Key Care Tips for all Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. Do not use abrasive cleansers 3.
mr Installation & Operating Instructions .steam _________________________________________________________________ ® template for control installation ( see 2-5⁄8” 3-7⁄8” 17 pg .
mr.steam ® Feel Good Inc. Products, information and specifications are subject to change without notice. For more information call Sales & Support at: 1.800.76.STEAM (East Coast) 1.800.72.STEAM (West Coast) 2019 © Sussman-Automatic Corporation MrSteam and des., AromaFlo, AutoFlush, AutoSteam, Butler Package, ChromaSteam, Clean Steam...
mr.steam ® STEAM HEAD ___________________________________________________________________________________________________________________________________________ I N S TA L L AT I O N I N S T R U C T I O N S 1/8" minimum clearance required when Acrylic Shield is used. See installation instructions provided with the Acrylic Shield.
Installation, Operation and Maintenance Manual Linear Steam Head Residential Model: 104480 ____________________ MPORTANT: Leave this material with t he homeowner. _IMPORTANT: _____ _Leave _ _this _ _material _ _ _with _ _the_homeowner. __ mr.steam ® Feel Good Inc.
Linear Steam Head ® ® Model 104480 TA B L E O F C O N T E N T S Important Safety Information . . . . . . . . . . . .1-2 Installer Section: Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Dimensional Information . . . . . . . . . . . . . . . . . .3 General Installation . . . . . . . . . . . . . . . . . . . . . . .4 Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Installer and Home Owner Section: Steam Emission Zone . . . . . . . . . . . . . . . . . . . . .
Linear Steam Head ® Installer Section READ ME FIRST! As you follow these instructions, you will notice and symbols. This information is important for the proper, safe and trouble free installation of the Linear Steam Head. These are types of potential hazards that may occur if installation instructions are not carefully followed: This signals a situation where injury or property damage may occur if you do not follow instructions.
Linear Steam Head ® Installer Section Steambath controls feature an integral or remote temperature sensor that senses room temperature. Install the linear steam head in a location where steam emission will not come in direct contact with the control or remote temperature sensor. Failure to follow these instructions may result in poor temperature control, a hazardous condition, scalding or personal injury.
Linear Steam Head ® ® Installer Section Model 104480 Bracket Adjustment Screws Adjustable Brackets P104481 - Linear Steam Head BOX CONTENTS: • Linear Steam Head • Faceplate • Diverter • AromaTray • Silicone Sealant • Installation Instructions Dimensional Information 104483 - Faceplate 104484 - Diverter 104482 - AromaTray Linear SteamHead shown without the optional faceplate or diverter.
Linear Steam Head ® ® Installer Section Model 104480 Steam Head Installation Linear SteamHead shown without the optional faceplate or diverter. STEP 1. Confirm proper stud spacing: The studs must have a minimum spacing of 14-1/8” and a maximum spacing 19". If the stud spacing is outside the required range then shim or otherwise reposition the studs as required.
Linear Steam Head ® ® Installer Section Model 104480 Optional Faceplate Installation The steam head is supplied with an optional faceplate. It is not required for the functional operation of the steam head. The faceplate is a decorative accessory and is available in (8) finishes. An optional Escutcheon (remodel plate) is available for purchase, it's larger than faceplate and is available in (8) finishes.
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 Steam Emission Zone The Steam Emission Zone is the area in front of the steam head that contains dense, hot steam as it exits the steam head. Steam dissipates as it moves away from the steam head, and becomes less hot. The steam zone is the area where contact with steam presentees a scalding hazard. The steam head must be installed in a location to ensure that a steam bather will not be near the steam emission zone.
Linear Steam Head ® Installer and Home Owner Section ® Model 104480 Diverter The Linear SteamHead is supplied with an optional steam diverter. The steam diverter is used to reduce the steam emission zone as required to avoid contact between a steam bather and direct steam emissions. Supplied steam diverter does not have decorative finish. Steam diverters with decorative finish are available for purchase. Always use the diverter if any steam bather may come into contact with direct steam emissions.
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 AromaTray The AromaTray is for use with MrSteam Essential Oils. Place a few drops of Essential Oils in the AromaTray as shown to provide a fragrant steam bath experience. Read the instructions provided with the MrSteam Essential oils to insure a pleasant and safe aromatic steam bathing experience.
Linear Steam Head ® ® Using MrSteam Essential Oils ® ® Model 104480 Enjoy Mr.Steam essential oils by placing a drop or two, into your Mr.Steam AromaTray as shown in the illustration. Only use Enjoy Mr.Steam essential by placing a drop or two, intoayour Mr.Steam AromaTray as shown in the illustration. Only use Mr.Steam essential oils inoils a Mr.Steam AromaTray. Contact MrSteam customer or technical Service representative for essential Mr.Steam essential oils in a Mr.Steam AromaTray.
Linear Steam Head ® ® Model 104480 mr.steam ® 104482 - AromaTray 104483 - Faceplate Feel Good Inc.
I N S TA L L AT I O N I N S T R U C T I O N S Package Contents: SteamLinx Module and Mobile App allows for seamless control of time and temperature using your smart phone or mobile device. SteamLinx works with all MrSteam controls (for MS generators SN 1174000 and up). • SteamLinx A with Integral Cable • SteamLinx B and Ethernet Cable • Power Supply and Cable • Instructions These instructions contain safety alert symbols and panels.
2 Connecting SteamLinx B to the Home Router Home Router • Plug the blue ethernet cable provided, into an ethernet slot on the back of the home router. Power • Plug the power Supply supply into a 120V outlet. 3’ Cable Ethernet Cable (3’) 3 Connecting SteamLinx to the Internet 4 Troubleshooting: Blinking LED Troubleshooting: Indicator Lights Units are out of range or not paired LEDs • Insure the mobile device is on the WiFi network.
mr.steam ® Optional AutoFlush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable National and Local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1/2" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Optional AutoFlush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Technical Specifications Condensation Pan 103867 & 104402 Mr.Steam strongly recommends the use of a condensation pan in the unlikely event of a plumbing leak. Locate the condensation pan on a solid level surface and place the steam generator inside the condensation pan. Insure the steam generator is level. All plumbing shall be performed by a qualified licensed plumber and in accordance with applicable national and local codes.