Installation Sheet

The following general information should be
used in conjunction with consultations with a qualified
architect, designer and contractor in determining factors
necessary in providing a suitable and safe steam room.
This document contains important safety,
operation and maintenance information. After installation
leave these instructions with the homeowner. Do not discard
this instructions. Failure to leave the instructions with the
homeowner may result in property damage or personal injury.
Use one or more Linear Steam Heads for
MrSteam steam generator models MS90 – MS400 and
MSSUPER1–MSSUPER3, SAH3000-SAH6000.
Use two or more Linear Steam Heads for
MrSteam steam generators Models MX4, MX5 and MX6.
Failure to use two or more steam heads may result in steam
head operation where incidental contact by the bather with
direct steam emission may occur. Failure to use two or more
steam heads may result in a leak within the wall cavity and
cause problems associated with leaks, moisture and
property damage from leaks. Failure to use two or more
steam heads may result in a hazardous condition, scalding or
personal injury.
Do not use Linear Steam Head for any
MrSteam steam generator that is not one of the following
models: MS90 –MS400, MSSUPER1–MSSUPER3, SAH3000-
SAH6000 or MX4 –MX6. Failure to follow these instructions
may result in a leak within the wall cavity and cause
problems associated with leaks, moisture and property
damage from leaks. Failure to follow these instructions may
result in a hazardous condition, scalding or personal injury.
Do not use the Linear Steam Head with any
steam system that is not a MrSteam steam system. Failure to
follow these instructions may result in a leak within the wall
cavity and cause problems associated with leaks, moisture and
property damage from leaks. Failure to follow these instructions
may result in a hazardous condition, scalding or personal injury.
Because the steam head and direct steam
emission are very hot, locate the steam head(s) where
incidental contact by the user with the steam head(s) or
direct steam emission cannot occur. Do not locate the steam
head(s) in any location where the steam emission zone is
near a seat,bench or any space occupied by any persons.
Failure to following these directions may result in a
hazardous condition, scalding or personal injury.
Linear Steam Heads are for residential use
only. Do not use any Linear Steam Heads for commercial
installations or with commercial steam generators (including
Day Spas). Using Linear Steam Heads for commercial
installations or installations with commercial steam
generators may result in a leak within the wall cavity and
cause problems associated with leaks, moisture and
property damage from leaks. Using Linear Steam Heads for
commercial installations or installations with commercial
steam generators may result in a hazardous condition,
scalding or personal injury.
Do not use the Linear Steam Head with any
steam system that includes equipment or devices not
supplied by MrSteam, including but not limited to water
softeners. Failure to follow these instructions may result in a
leak within the wall cavity and cause problems associated
with leaks, moisture and property damage from leaks.
Failure to follow these instructions may result in a hazardous
condition, scalding or personal injury.
Only install the linear steam head in a
horizontal orientation as shown in fig 3. Failure to follow
these instructions may result in a leak within the wall cavity
and cause problems associated with leaks, moisture and
property damage from leaks. Failure to follow these
instructions may result in a hazardous condition, scalding or
personal injury.
Insulate the linear steam head and piping as
required to prevent elevated temperatures, including within
the wall cavity. Do not locate the steam head or plumbing near
any materials, including wiring, devices, or products that may
be adversely affected by elevated temperatures. Check with
the manufacturer of materials, wiring, devices, or products for
suitability for operation at elevated temperatures. Use only
insulation rated for 212F or higher steam applications. Failure
to follow these instructions may result in the damage or failure
of materials, wiring, devices, or products. Failure to follow
these instructions may result in leaks, and cause problems
associated with leaks, moisture and property damage from
leaks. Failure to follow these instructions may result in a
hazardous condition, scalding or personal injury.
READ ME FIRST! As you follow these instructions, you
will notice and symbols. This
information is important for the proper, safe and trouble free
installation of the Linear Steam Head. These are types of
potential hazards that may occur if installation instructions
are not carefully followed:
This signals a situation where injury or
property damage may occur if you do not follow instructions.
This highlights information that is especially
relevant to a problem free installation.
All information in these instructions is based on the latest
information available at the time of publication. Sussman-
Automatic Corporation reserves the right to make changes
at any time without notice.
Installer Section
Linear Steam Head
1
®
®
Model 104480