iDream/iDream2/iDreamX iSteam3 Control AromaSteam SteamHead SteamLinx Mobile App AudioSteam3 System Square Speakers ChromaSteam3 System AromaSteam System MS / Super AutoFlush MX AutoFlush Condensation Pan PUR100514 PUR100421 PUR100518 PUR100516 PUR100401SQ PUR100515 PUR100402 PUR100200E PUR100532 TS0012 07-17 10-15 01-18 01-18 05-13 01-19 12.18.
Installation, Operation & Maintenance Manual iSteam 3 Control ® mr.steam ® Feel Good Inc.
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ ME FIRST! ! WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and eff icient installation and operation of this generator.
Table of Contents: Important Safety Instructions......................... 2 Box Contents: INSTALLER INFORMATION • iSteam®3 Control Installation Template .................................... 2 • Control Cable (30 ft.) Box Content.................................................. 3 • Steamhead Dimensional Information............................... 3 • Tube of Silicone Sealant Before Installing............................................. 4 • Owner’s Manual Locating the Control....................
mr INSTALLER INFORMATION .steam __________________________________________________________________ ® Before Installing ! WARNING To avoid unintentional steambath op- ! CAUTION Do not route iSteam3 control wiring inside conduit together with power lines or close to hot water or steam piping. Doing so may result in an inoperative or hazardous installation. Do not alter or modify any Mr. Steam products including the steam generator or iSteam3 control.
mr INSTALLER INFORMATION .steam __________________________________________________________________ ® Locating the Control 1b Determine the desired installation location of the control. The iSteam®3 controls are designed to be installed inside or outside the steam room as a matter of personal preference. If the control is installed inside the steam room: • Locate the control 4-5 feet above the floor near the bather seating area. • The control features an integral temperature sensor.
6b mr INSTALLER INFORMATION .steam __________________________________________________________________ ® Installation with Optional Rough-In Box 6a (cont.) IMPORTANT NOTE: Be careful not to strain, staple, pinch or otherwise damage the cables. Route cables as required to permit replacement. Do not route cables inside conduit together with power lines or close to hot water or steam piping. 7 Step 6 Rough-In box used as a guide to cut out the opening.
mr INSTALLER INFORMATION .steam __________________________________________________________________ ® Installation Instructions for iSteam®3 STEP 1 PLUG the 30’ control cable into the iSteam3 control pigtail (1a). Turn the generator on and test the control to verify correct connection. With proper function, proceed to Step 2. ! CAUTION Do not force or twist cable ends together. Forcing or twisting cable ends may damage the connectors.
mr INSTALLER INFORMATION .steam __________________________________________________________________ ® Installation Instructions for iSteam®3 (cont.) Step 2 2a Peel the double stick adhesive off the back of the iSteam3 control (2a). Apply a bead of silicone around the rear of the iSteam3 control to create a moisture seal (2b). Carefully feed the cables into the rough-in box and secure the control to the wall. Care must be taken to not pinch the cables. Ensure the control is level.
mr.steam H O M E O W N E R ® When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ ME FIRST! ! WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and eff icient installation and operation of this generator.
mr USER/HOMEOWNER INFORMATION .steam __________________________________________________________________ ® Operating Instructions ! WARNING Set the steam bathing duration and temperature according to personal preference, however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels. Set the duration at 10 minutes max. to gauge comfort and safety levels. This will allow the steam generator to heat up and begin producing steam.
mr USER/HOMEOWNER INFORMATION .steam __________________________________________________________________ ® Set Temperature Screen 101 F 12:16 PM 97 Press the TEMPERATURE button on the Dashboard to access the SET TEMPERATURE screen. The control is preset and will display a temperature setting of 110° F (default setting). Swipe your finger up and down to adjust the desired temperature (80 ̊ - 120 ̊ F) in one degree increments.
mr USER/HOMEOWNER INFORMATION .steam __________________________________________________________________ ® AudioSteam 97 Press the music icon to access the AudioSteam screen. Press the MUSIC button to turn on AudioSteam. When AudioSteam is ON, pressing the MUSIC button will turn it OFF. Press the AudioSteam Dashboard button to control the music. When paired to a Bluetooth® device, iSteam®3 will display the song title, artist and album name. If listening to the FM radio, the station number will be shown.
mr USER/HOMEOWNER INFORMATION .steam __________________________________________________________________ ® 97 Settings Screen F 12:16 PM System Settings The Setting Screen allows access to less frequently used screens. Date & Time AutoStart Passcode About System Setting 97 Scroll through the System Settings list and select which to adjust. F 12:16 PM Temperature Units Flip Screen Temperature Units. Adjust between ˚F and ˚C System Setting User Interface Color Flip Screen.
mr USER/HOMEOWNER INSTALLER INFORMATION .steam __________________________________________________________________ ® AutoStart Turn AutoStart ON or OFF ! WARNING AutoStart will automatically turn the steam generator on at your preset time. Activating the steam in an occupied room may subject persons to the hazards described in this manual. Only activate the steambath if the steam room door is closed.
mr USER/HOMEOWNER INFORMATION .steam __________________________________________________________________ ® Care Tips Use only mild soap and water on a soft cloth to clean the control. Do not use abrasive cleansers. Safety and Operating Information ! WARNING A peel and stick warning sticker is provided in the MrSteam steam generator Installation, Operation and Maintenance Manual. This manual is provided with every steam generator.
mr.steam ® Feel Good Inc. ® www.mrsteam.com Products, information and specifications are subject to change without notice. For more information call Sales & Support at 1.800.76.STEAM (East Coast) or 1.800.72.STEAM (West Coast) for more information. mr.steam Sussman-Automatic Corporation ® ® I hello@mrsteam.com I www.mrsteam.com 43-20 34th Street, Long Island City, NY 11101 I 9410 S. La Cienega Blvd.
mr.steam ® STEAM HEAD ___________________________________________________________________________________________________________________________________________ I N S TA L L AT I O N I N S T R U C T I O N S 1/8" minimum clearance required when Acrylic Shield is used. See installation instructions provided with the Acrylic Shield.
I N S TA L L AT I O N I N S T R U C T I O N S Package Contents: SteamLinx Module and Mobile App allows for seamless control of time and temperature using your smart phone or mobile device. SteamLinx works with all MrSteam controls (for MS generators SN 1174000 and up). • SteamLinx A with Integral Cable • SteamLinx B and Ethernet Cable • Power Supply and Cable • Instructions These instructions contain safety alert symbols and panels.
2 Connecting SteamLinx B to the Home Router Home Router • Plug the blue ethernet cable provided, into an ethernet slot on the back of the home router. Power • Plug the power Supply supply into a 120V outlet. 3’ Cable Ethernet Cable (3’) 3 Connecting SteamLinx to the Internet 4 Troubleshooting: Blinking LED Troubleshooting: Indicator Lights Units are out of range or not paired LEDs • Insure the mobile device is on the WiFi network.
Installation, Operation and Maintenance Manual Installation, Operation, and Maintenance Manual AudioSteam ® mr.steam ® Feel Good Inc.
IMPORTANT SAFETY INFORMATION READ ME FIRST: 1. Read and follow all instructions within this technical manual. 2. Heed all warnings, cautions, notices, and important notes. 3. Save this technical manual and leave with the homeowner. ABOUT WARNINGS, CAUTIONS, NOTICES, AND IMPORTANT NOTES: As you follow the instructions in this technical manual, you will see four types of callouts: WARNINGS, CAUTIONS, NOTICES, and IMPORTANT NOTES.
IMPORTANT SAFETY INFORMATION (cont.) ! WARNING Before installing or connecting the AudioSteam, please read the following: • To prevent a shock hazard, do not disassemble or alter the AudioSteam. • To prevent overtemperature shutoff and equipment damage, do not use foam to insulate the AudioSteam. • To prevent a shock hazard, turn power off before servicing or changing any cable connections in the AudioSteam.
mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE AudioSteam® Table of Contents INSTALLER INSTRUCTIONS 1. General information................................................. 5 Box Contents.................................................................5 AudioSteamJ2 General installation.............................5-6 2. Installing AudioSteam.............................................. 7 AudioSteam Dimensions...............................................
mr.steam ® AudioSteam® INSTALLATION, OPERATION, AND MAINTENANCE I N S TA L L E R I N S T R U C T I O N S 1. General Information Box Contents AudioSteam FM antenna Control cable AudioSteam General Installation Figure 1 shows how the AudioSteam interconnects with the steam generator, iSteam3, and audio speakers. IMPORTANT NOTE AudioSteam only integrates with iSteam3. Figure 2 shows how to use the AudioSteam as a standalone system within your steam room (i.e.
INSTALLER mr.
® INSTALLATION, OPERATION, AND MAINTENANCE AudioSteam® 2. Installing AudioSteam AudioSteam Dimensions Figure 3 shows the face-on dimensions of AudioSteam. Figure 4 shows the side-view dimensions of AudioSteam. ! WARNING Shock hazard. Do not place the control box in a location where it can get wet. Locating and Installing AudioSteam To prevent water from getting inside the device, AudioSteam should be mounted on two stable vertical surfaces (e.g., studs) as shown in Figure 5.
INSTALLER mr.steam ® AudioSteam® INSTALLATION, OPERATION, AND MAINTENANCE 3. Connecting AudioSteam Connecting AudioSteam ! WARNING To connect AudioSteam to the steam generator, perform one or more of the following connections: • Connect the FM antenna (included) and auxiliary cord to AudioSteam. • Connect speakers and subwoofer to AudioSteam with speaker wire. • Connect AudioSteam to the steam generator’s motherboard or daughterboard with the AudioSteam control cord.
® INSTALLATION, OPERATION, AND MAINTENANCE AudioSteam® Connecting the FM Antenna and Auxiliary Cord 1. Plug the included FM antenna into the antenna output and route the wire through the strain relief channel as illustrated (Figure 9). For best reception, fully deploy the antenna in a vertical orientation outside of the AudioSteam housing. 2. Connect a 1/8” (3.
INSTALLER mr.steam ® AudioSteam® INSTALLATION, OPERATION, AND MAINTENANCE Connecting AudioSteam to the Steam Generator Power Cord to 120V Grounded Outlet To operate the AudioSteam via iSteam3, you must connect the AudioSteam (Figure 12) to an internal connector in the steam generator. Control Cable Connection Port ! WARNING Shock hazard. Power must be disconnected at the main electrical supply before removing the steam generator cover.
® INSTALLATION, OPERATION, AND MAINTENANCE Pairing a Bluetooth-Enabled Device Before playing a Bluetooth-enabled device via iSteam3 (see “Operating AudioSteam” on Page 17), you must pair your device to AudioSteam. To pair a Bluetooth-enabled device to AudioSteam: 1. Ensure that the mobile device is in range of AudioSteam, and that it is powered on and Bluetooth is turned on. 2. Open the Bluetooth settings on your device. 3. Select AudioSteam in the list of discoverable Bluetooth devices. 4.
INSTALLER mr.steam ® AudioSteam® INSTALLATION, OPERATION, AND MAINTENANCE 4. AudioSteam Specifications ENVIRONMENTAL RATINGS FM RECEIVER Operating temperature: -4 °F (-20 °C) to 140 °F (60 °C) Frequency band: 87.5 MHz to 107.9 MHz Storage temperature: -22 °F (-30 °C) to 185 °F (85 °C) RF sensitivity: 2.2 μV Humidity: 70% max Harmonic distortion: 0.
® INSTALLATION, OPERATION, AND MAINTENANCE AudioSteam® 5. Regulatory Statements FCC Compliance Statement Contains Transmitter Module FCC ID: A8TBM23SPKXYC2A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE AudioSteam® HOMEOWNER/END-USER INSTRUCTIONS 6. About AudioSteam AudioSteam offers you the perfect means to bring music into your steam room. AudioSteam is compatible with numerous audio sources: • Connect to a mobile device or digital music player using the auxiliary audio input. • Connect to a mobile device via Bluetooth. • Tune in to an FM station using the AudioSteam’s integrated FM receiver.
® AudioSteam® INSTALLATION, OPERATION, AND MAINTENANCE 7. Operating AudioSteam (cont.) To Operate AudioSteam using iSteam3: 1. Boot iSteam3 and wait for the iSteam3 home screen to appear. 2. To turn on AudioSteam (Figure 14), tap the music icon (A), and then tap the MUSIC button (B). 3. Tap the settings icon (A in Figure 15). 4. A list of available playback devices will appear (Figure 16). Tap the desired device (A), and then tap the play icon (B).
mr.steam ® Connecting Multiple Accessories to the Steam Generator To operate the SteamLinx, AudioSteam3 and ChromaSteam3 via iSteam3, you must connect the accessories to an internal connector in the steam generator. Shock hazard. Power must be disconnected at the main electrical supply before removing the steam generator cover. For information about the steam generator, refer to the installation, operation, and maintenance manual supplied with the steam generator (also found at www.mrsteam.
mr.steam ® Feel Good Inc. ® www.mrsteam.com Products, information and specifications are subject to change without notice. Call Sales & Support at 1 800 76 STEAM (East Coast) or 1 800 72 STEAM (West Coast) for more information. mr.steam ® Sussman-Automatic Corporation® • www.mrsteam.com • hello@mrsteam.com 43-20 34th Street, Long Island City NY 11101 9410 S. La Cienega Blvd.
mr.steam ® Square Speakers ___________________________________________________________________________________________________________________________________ INSTAL LATI ON INS TRUCTIONS Model MS-Speakers SQ PACKAGE CONTENTS: 2 Speakers 1 Installation Instructions 2 Templates _______________________________________________________ SPEAKER RATINGS: 60 watt peak / 30 watt RMS / 8 ohm impedance Brackets 1. Cut a 5 13⁄16” x 5 13⁄16” hole to mount each speaker.
mr.steam ® S Q U A R E S P E A K E R T E M P L AT E 513⁄16” 513⁄16” mr.steam® Sussman-Automatic Corporation® • www.mrsteam.com • hello@mrsteam.com 43-20 34th Street, Long Island City, NY 11101 TEL: 1-800-76-STEAM FAX: (718) 472-3256 9410 S. La Cienega Blvd.
mr.steam ® S Q U A R E S P E A K E R T E M P L AT E 513⁄16” 513⁄16” mr.steam® Sussman-Automatic Corporation® • www.mrsteam.com • hello@mrsteam.com 43-20 34th Street, Long Island City, NY 11101 TEL: 1-800-76-STEAM FAX: (718) 472-3256 9410 S. La Cienega Blvd.
____ ____ _ IMPO _________ _ RTA NT: L _________ THE ____ E O A W VE T ____ ____ NER/O HIS M _________ ____ P ___ ANU ____ ERATO AL W ____ R OR I T ____ H A TT ____ ____ ENDAN ___ T ____ ____ Installation, Operation, and Maintenance Manual ChromaSteam 3 ® mr.steam ® Feel Good Inc.
IMPORTANT SAFETY INFORMATION READ ME FIRST: 1. Read and follow all instructions within this technical manual. 2. Heed all warnings, cautions, notices, and important notes. 3. Save this technical manual and leave with the homeowner. ABOUT WARNINGS, CAUTIONS, NOTICES, AND IMPORTANT NOTES: As you follow the instructions in this technical manual, you will see four types of callouts: WARNINGS, CAUTIONS, NOTICES, and IMPORTANT NOTES.
mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 Table of Contents INSTALLER INSTRUCTIONS General Information Box Contents........................................................................................ 4 Color Matching the Connections......................................................... 4 General Installation................................................................................ 5 Installing the ChromaSteam3 Control Box..........................................
mr.
® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ______________________________________________________________________________________ General Installation Figure 3 shows how the ChromaSteam3 fixture and control box interconnect with each other, and with the steam generator and iSteam3. MPORTANT NOTES • The included ChromaSteam3 control cable is 30 feet long. Ensure that the ChromaSteam3 fixture and control box are located accordingly.
INSTALLER mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 Installing the ChromaSteam3 Control Box Control Box Dimensions NOTICE • To prevent product or property damage, do not expose control box to temperatures above 140 °F (60 °C). Do not locate control box in an attic or any location where ambient temperatures may exceed 140 °F (60 °C). • Do not locate control box next to heat sources, such as hot air registers, air conditioner condensers, etc.
® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ______________________________________________________________________________________ Installing the ChromaSteam3 Fixture Fixture Dimensions Figure 5 PORTION IN CEILING PORTION IN STEAM ROOM Figure 6 7 All drawings are for illustrative purposes only. INSTALLER mr.
INSTALLER mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ___________________________________________________________________________________ Installing the Junction Box ! WARNING Functions of the Junction Box: 1. Allows precisely location of the ChromaSteam3 fixture within the steam room ceiling. 2. Provides a secure and easily identifiable holder for the control cable while the steam room is being constructed. 3.
® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ______________________________________________________________________________________ Ceiling joist Knockouts Junction box tabs Figure 7 Figure 8 End of 30-foot control cable or one of the longer ends of Duo cable Figure 9 Figure 10 9 All drawings are for illustrative purposes only. INSTALLER mr.
INSTALLER mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ___________________________________________________________________________________ Installing the Fixture To Install the Fixture: 1. Connect the ChromaSteam3 fixture’s pigtail to the 30-foot control cable or Duo cable in the junction box (Figure 11). IMPORTANT NOTE: Test that the fixture operates correctly prior to continuing with the following steps. 2.
® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ______________________________________________________________________________________ Connecting the ChromaSteam3 Fixture to the ChromaSteam3 Control Box ! WARNING • Shock Hazard. Ensure that power is turned off during installation. Turn off power at breaker panel. • Shock Hazard. To prevent electric shock, do not remove the screws on the back of the control box. No user-serviceable parts inside.
INSTALLER mr.steam ® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ___________________________________________________________________________________ Connecting the ChromaSteam3 Control Box to the Steam Generator The final connection is made from the ChromaSteam control box (Figure 19) to an internal connector in the steam generator. ! WARNING Shock Hazard. Power must be disconnected at the main electrical supply before removing the steam generator cover.
® INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®3 ______________________________________________________________________________________ ChromaSteam3 Specifications ENVIRONMENTAL RATINGS Control box fixture Operating temperature: -4 °F (-20 °C) to 140 °F (60 °C) -4 °F (-20 °C) to 140 °F (60 °C) Storage temperature: -22 °F (-30 °C) to 185 °F (85 °C) -22 °F (-30 °C) to 185 °F (85 °C) Humidity: 70% max 100%, condensing Water resistance: IPX5 Designed to IP67 mechanical Control box fix
mr.steam steam ®® INSTALLATION, OPERATION, AND MAINTENANCE INSTALLATION, OPERATION, AND MAINTENANCE ChromaSteam®®33 ChromaSteam HOMEOWNER/END-USER INSTRUCTIONS About ChromaSteam3 Like water and heat, light is a fundamental life force and may improve your physical and mental state. The Mr.
® INSTALLATION, OPERATION, AND MAINTENANCE Operating ChromaSteam3 ChromaSteam®3 ! CAUTION You can control the ChromaSteam3 LED module from within your steam room using the iSteam3 control. Select from 78,000 different colors — and control the brightness of the light — all from a simple interface. To operate the ChromaSteam3 using iSteam3: Note that ChromaSteam3 is for mood lighting only, and does not substitute for general shower illumination. NOTICE 1.
mr.steam ® Feel Good Inc. ® FOR MORE INFORMATION PLEASE CALL Sales & Support EAST COAST 1.800.76.STEAM WEST COAST 1.800.72.STEAM www.mrsteam.com mr.steam ® Sussman-Automatic Corporation® • www.mrsteam.com • hello@mrsteam.com Products, information and 43-20 34th Street, Long Island City NY 11101 9410 S. La Cienega Blvd., Inglewood CA 90301 tel: 1 800 76 STEAM fax: 718 472 3256 tel: 1 800 72 STEAM fax: 310 216 2944 specifications are subject to change without notice.
Installation, Operation & Maintenance Manual AromaSteam Fragrance Metering Pump System for Residential and Day Spa Steam Rooms ® Part Number MS AROMA (120V) __________________________________ IMPORTANT: Leave this material with the home owner. __________________________________ mr.steam l ® Feel Good Inc. ! WARNING This installation, operation and maintenance manual is for general reference.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Before Installing T a b l e o f C ont e nt s Carefully inspect the AromaSteam pump and packaging for shipping damage. In the event of shipping damage, please contact the carrier for claim information. Our customer service department can assist you with product replacement.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Box Contents 8 ft.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N ! WARNING FLAMMABLE LIQUID AND VAPOR • Keep the pump and fragrance away from heat, sparks, electrical outlets, open flames such as candles and hot surfaces. • No smoking. • Keep Out of the Reach of Children. • Use only non-sparking tools. Take precautionary measures against static discharge.
mr AromaSteam Operation and Installation Instructions .
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N General System Dimensions 5 -10 ft. optimal Steam Head Steam Pipe Steam Pipe T Check Valve (inside steam room) 6 ft. max Pressure Hose PUMP SPECS Dimensions: Weight: Motor voltage Current Draw Steam Generator Pump 7.5”W x 4.5”H x 4.5”D 5 pounds 120VAC, 50/60 Hz 0.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N WARNING STICKER The warning label (supplied on page 2) shall be posted in a conspicuous location next to the steam room door.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Installing the 90 degree T and Check Valve 1. For optimal results locate a brass 90 degree T (not provided) in the steam supply line within 5-10 feet of the steam head. If using copper tubing for steam lines, install a female 1/2 NPT or 1/4 NPT reducing Tee in the steam line facing downward. 2.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Installation of Suction Tube to the Pump 1. Insert the suction tube through the pump tightening nut and collar and firmly push the tube onto the tube holder. 2. Screw the suction tube tightening nut to the suction side of the pump. IMPORTANT NOTE: HAND-Tighten only.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Priming the Pump 1. Insure MrSteam fragrance container is full. 2. Insert a short piece of soft injector tube onto the tip of the injector (see Fig. 1). 3. Insert the open end of the injector tube onto the pressure valve (see Fig. 1). 4.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N AromaSteam Wiring Schematic Electrical Connection of AromaSteam System AromaSteam Pump ! CAUTION This AromaSteam system is factory wired.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® Operation Powering Up the Pump IMPORTANT NOTE: This step only needs to be performed during installation. 1. The pump needs to be turned on before it can be used I N S TA L L E R S E C T I O N Fragrance Setting Knob Power Button 2. Press and hold the power button for 3 seconds. The LED will turn on solid red. Pump LED light: Flashing Green LED on.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Troubleshooting ! WARNING To avoid electric shock, disconnect power to pump before servicing Pump fragrance delivery too much or too little Pump does not prime ! WARNING The AromaSteam system has been factory set to deliver a suitable amount of aromatic fragrance into a typical sized steam room.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N REPLACEMENT parts Check Valve (5 pcs.) 104240 Tube (per foot) 104255 O-Ring (3 pcs.) 104275 Tube Connector (3 pcs) 104250 Pump Head 104239 Caddy (104318) Request Cable 104307 Syringe (103983) Priming Tube (6”) 104322 Tube Connector (3 pcs) 104250 Tube (per foot) 104255 Foot Valve (2 pcs.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Installing the Caddy: Box Contents: Tools required: • Stainless steel caddy • Mounting screws (2) • Instructions • Cordless drill with a Phillips bit • Level *Use only non-sparking tools. Take precautionary measures against static discharge Pump Suction Hose Locating the Caddy: 1.
AromaSteam mr AromaSteamOperation Operationand andInstallation InstallationInstructions Instructions .steam _____________________________________________________________________________________________ ______________________________________________________________________________________________ ® I N S TA L L E R S E C T I O N Mounting the Caddy on a Floor: 1. Use the two mounting screws provided to secure the caddy using the two holes at the bottom of the caddy (Diagram 3). 2.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® hom e own e r S e ction The AromaSteam’s state-of-the-art pump introduces fragrance into the steam pipe and into your steam shower. MrSteam Aroma is Available in These Five Fragrances: Fragrance Part No. Container Volume.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® HOMEOWNER SECTION Important Safety Instructions Read and Follow all Instructions ! WARNING FLAMMABLE LIQUID AND VAPOR • Keep the pump and fragrance away from heat, sparks, electrical outlets, open flames such as candles and hot surfaces. • No smoking. • Keep Out of the Reach of Children. • Contains denatured ethyl alcohol.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® HOMEOWNER SECTION Locating the Caddy/Fragrance: 1. Place in a location that allows visual monitoring of the fragrances level. 2. Place in a location that allows for easy replacement of the fragrance container. 3. The caddy should not be installed in areas accessible to children. A locked room is strongly recommended (ie: utility room). 4.
mr AromaSteam Operation and Installation Instructions .steam _____________________________________________________________________________________________ ® HOMEOWNER SECTION Operation (cont.) Adjusting the Amount of Fragrance Delivery The AromaSteam system has been factory set to deliver a suitable amount of fragrance into a typical sized steam room. Do not exceed the maximum setting. Please contact the MrSteam Technical Service Department before changing this setting.
Installation and Operation Manual AromaSteam Fragrance & Caddy Instructions for the Use and Installation of Residential and Day Spa Fragrances and Caddy ® mr.steam l ® Feel Good Inc.
mr.steam ® Optional Autoflush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1/2" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Optional AutoFlush® System ____________________________________________________________________________________________________________________________________________ INSTA LLAT ION INS TRUCTI ONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions.
INSTALLATION INSTRUCTIONS 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available. The AutoFlush System valve outlet is threaded 1" NPT. Check plumbing code for receptor, trap and vent requirements. 2.
mr.steam ® Technical Specifications Condensation Pan 103867 & 104402 Mr.Steam strongly recommends the use of a condensation pan in the unlikely event of a plumbing leak. Locate the condensation pan on a solid level surface and place the steam generator inside the condensation pan. Insure the steam generator is level. All plumbing shall be performed by a qualified licensed plumber and in accordance with applicable national and local codes.
