WallSeat Installation Manual
Failure to use the lag bolts provided, or failure to tighten
the lag bolts properly may result in mounting failure and may result
in serious injury.
10. The lag bolts should completely penetrate the header.
Failure to install the mounting lag bolts so they penetrate
the header completely may result in serious injury.
11. Insert seat assembly to brackets. Place seat with the MrSteam logo
and fasteners on the bottom. See figure 3.
Failure to place the WallSeat with the fasteners on the
bottom may result in the user contacting hot fasteners and may
result in a burn hazard.
12. Insert hinge pins to both left and right brackets while the seat as-
sembly is in vertical position. Securely tighten both hinge pins, using
Allen wrench provided. See figure 3.
13. Test the finished, mounted WallSeat with 300 lbs. (113 kg.) load in
a safe manner.
Testing with heaving loads can be dangerous. Testing
should be performed by a qualified professional only. Failure to handle
or test heavy loads properly may result in invalid test results, mounting
failure or serious injury. Do not test using people as the weight.
14. If the seat is not parallel to the floor when it is in the lowered or
seated position use the level adjustment screws to adjust the
mounted WallSeat. An Allen wrench is provided for this purpose (See
figure 5). Adjust both level screws so the WallSeat is even and it con-
tacts both brackets at the same time.
15. The following section contains important information for the home-
owner. Leave these instructions with the homeowner. Do not discard.
Failure to leave these instructions with the homeowner
may result in misuse and serious injury.
16. The WallSeat has instructions for the homeowner attached to the
WallSeat. DO NOT REMOVE THESE INSTRUCTIONS. These instruc-
tions contain important information for the homeowner. See figure 5.
Removing the instructions for the homeowner may result
in misuse of the WallSeat and may result in serious injury.
H O M E O W N E R ’ S S E C T I O N
THE MAXIMUM WEIGHT CAPACITY
OF THE WALLSEAT IS 250 LBS. (113 kg) WHEN
INSTALLED IN ACCORDANCE WITH THESE
INSTRUCTIONS. Exceeding the maximum weight
may cause mounting failure, resulting in serious
injury. Persons weighing more than 250 lbs.
should NEVER use the seat .
NEVER use the WallSeat for any
purpose other than sitting. NEVER stand on the
WallSeat. Standing on the WallSeat may result in
serious injury.
NEVER allow more than one person
to use the WallSeat. It is intended for one person
only. Use by more than one person can result in
mounting failure and serious injury.
NEVER use the WallSeat for any other
purpose other than passive sitting and still relax-
ation. Do not engage in any activities or motions
that result in excessive loading or stress on the
WallSeat. Such use may result in mounting failure
and serious injury.
Contact with teak may result in skin ir-
ritation or allergic reactions. If you are allergic to
teak use a towel to prevent direct contact with
the WallSeat.
Discontinue use of the WallSeat if any
parts appear damaged, degraded or loose.
Clean the WallSeat with mild soap
and water. Do not use abrasive cleaning products.
Level
Adjustment
Screws
H
o
m
e
o
w
n
e
r
I
n
s
t
r
u
c
t
i
o
n
s
P
L
E
A
S
E
L
E
A
V
E
T
H
I
S
G
U
I
D
E
I
N
P
L
A
C
E
F
O
R
T
H
E
H
O
M
E
O
W
N
E
R
Fig. 5
Level WallSeat
1
4
7
/
8
”
1
9
3
/
4
”
1
5
5
/
16
”
1
11
/
1
6
Fig. 4
WallSeat
Assembly
WALLSEAT INSTALLATION INSTRUCTIONS
3
____________________________________________________________________________________
PUR 100511A. 7/17