Operating Guide

mr
.
steam
®
towelwarmers Hydronic Models
_________________________________________________________________
Installation and Operating Instructions
13
Escutcheons Brass Inserts Valves Screws
Washers Set Screws Mounting Backet Escutcheons Eccentric Coupling
Suitable only for closed loop non-potable hot
water systems. Tighten Towel Warmer unions only. Do not turn
valves as leaking may result
Do not use with water over 158 degrees F. (7o˚
C) Do not use with steam. Using with steam or water over 158
degrees F or 20 psig, may result in scalding or hazardous conditions.
1. Read this entire instruction manual thoroughly before beginning
installation and save these instructions.
2. Follow instructions accurately to make certain the Towel Warmer
is properly attached to the wall. FAILURE TO FOLLOW THESE
STEPS COULD RESULT IN PROBLEMS.
3. Do not use an abrasive cleaner on the Towel Warmer. A mild deter-
gent will clean and restore most units to their original beauty.
4. TO ENSURE FULL EFFICIENCY OF YOUR TOWEL WARMER, PLEASE
FOLLOW ALL THE INSTRUCTIONS CAREFULLY, OBSERVING THE
“CAUTION” NOTATIONS FOR EACH STEP.
5. Inlet water temperature should be between 120°F and 158°F.
DO NOT exceed this limit. A burn hazard may result.
GENERAL:
Most Towel Warmers provide enough heat to warm towels and pro-
vide supplemental heat to the room. Larger units may be sufficient
to serve as the sole heat source for a small bathroom.
Optional Brackets
Additional towel warmer support brackets are available for installa-
tions where plumbing does not provide a rigid support to secure the
towel warmer to the wall.
Bracket Part Numbers and Optional Finishes
Polished Chrome 103959PC Polished Gold 103959PG
Polished Brass 103959PB Satin Gold 103959SG
Polished Nickel 103959PN Antique Brass 103959AB
Pewter 103959P Oil Rubbed Bronze 103959ORB
Satin Nickel 103959SN
CAUTION
!
WARNING
!
WARNING
!
Fig. 1 Towel Warmer Installation Parts
Screws
_________________________________________
HOT WATER TOWEL WARMERS
_________________________________________
Dimensions (inches)
__________________
Model H W D BTU/hr
†
Weight (lbs.)*
_________________________________________
H542 29
7
⁄16 21 5 500 20
________________________________________
H552 25
13
⁄16 21 13 800 30
_________________________________________
H562 24
1
⁄16 21 5 900 30
_________________________________________
H572 38
1
⁄2 21 5 650 20
_________________________________________
†
At 158˚ F * without water
H
W
D
STEP 1: PRE-INSTALLATION
A. Select Installation Site: Make certain there is ample clearance on both
sides and back of the Towel Warmer.
NOTE: This unit is supplied with the proper hardware for installation.
Be sure wall construction is appropriate for hanging (see Step 3A).
B. Before beginning the installation of any Mr.Steam Hydronic Towel
Warmer, please note the following:
1. Maximum operating temperature should not exceed 158°F.
Any working water temperature higher than 158°F could create
a potential burn hazard.
NOTE: A closed loop non-potable hot water system is recommended.
Consult an authorized hot water system installer for hot water system
types.
STEP 2: INSPECT THE TOWEL WARMER
A. Unpack the Mr.Steam Towel Warmer carefully to avoid any damage
or loss of any part. When opening the box and unwrapping the
Towel Warmer, be sure that parts are not accidentally discarded
(see illustration, fig 1).
B. Mr.Steam Hydronic Towel Warmers are shipped in specially designed
shipping cartons. The entire surface of the Towel Warmer is hand-
wrapped to protect the finish. Check the for any sign of damage.