Please read this manual carefully before installation and keep it for future reference. Remote Control User Manual Due to updates and constantly improving performance, the information and instructions within this manual are subject to change without notice. Please visit www.mrcool.com/documentation to ensure you have the latest version of this manual. Version Date: 09-29-21 For more info visit www.mrcool.
Contents 1 Remote Controller Specifications & Quick Start Guide .............. 2 2 Handling the Remote Controller .................................................. 3 3 Easy Pro™ Remote Controller ....................................................... 4 Buttons & Functions ............................. 4 Remote Screen Indicators ................. 5 How to Use Basic Functions ............. 6 Setting the Timer .................................. 8 How to Use Advanced Functions ....
1 Installation Summary Remote Control Specifications & Quick Start Guide DIY® E-Star™: RG10A4(D1)/BGEFU1 Model Easy Pro™: RG10A (DS2)/BGEFU1 Rated Voltage 3.0V (Dry Batteries R03/LR03 x 2) Signal Receiving Range 26.25 ft.
Handling the Remote Controller Inserting and Replacing Batteries NOTES FOR USING REMOTE CONTROL Your air conditioning unit may come with two batteries (some units). Install the batteries in the remote control before use by following the steps below: 1. Slide the back cover from the remote control downward to expose the battery compartment. 2. Insert the batteries, making sure to match the (+) and (-) designations on the end of the batteries with the symbols inside the battery compartment. 3.
Operation Of Buttons Easy Pro™ Remote Controller 3 Buttons and Functions Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual. MODE Scrolls through operation modes in the following sequence: ON/OFF Turns the unit on or off.
Remote Screen Indicators Remote Screen Indicators Information that is displayed when the remote controller is turned on. Breeze Away display (some units) Active clean feature display Sleep mode display Follow me feature display Wireless control feature display(some units) Transmission: This indicator lights up when the remote transmits a signal to the indoor unit.
How to Use Basic Functions How to Use Basic Functions ATTENTION Please ensure the unit is plugged in and power is available before operation. AUTO Mode Select AUTO mode Set your desired temperature Turn on the air conditioner MODE NOTE: • In AUTO mode, the unit will automatically select COOL, FAN, or HEAT function based on the set temperature. • In AUTO mode, fan speed cannot be set or adjusted by the user.
Setting the Timer How To Use The Buttons Setting the TIMER TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON setting Press TIMER button to initiate the ON time sequence. Press Temperature UP or DOWN Point remote control at the unit button to set the desired time to and wait 1 second, the turn ON the unit. TIMER ON will be activated.
How To Use Advanced Functions How to Use Advanced Functions Swing function Press the SWING button 2s Swing Swing The horizontal louver will swing up and down automatically when pressing SWING button. Press it again to make it stop. Keep pressing the SWING button more than 2 seconds, this will activate the vertical louver swing function (Model dependent). Airflow direction If continue to press the SWING button, five different airflow directions can be set.
How To Use Advanced Functions ECO/GEAR function Pressing the iECO/GEAR button will allow you to select the energy efficiency modes in the following sequence: ECO GEAR (75%) GEAR (50%) Previous setting mode ECO...... NOTE: This function is only available under the COOL mode. ECO operation: Under COOL mode, press this button and the remote controller will automatically adjust the temperature to 75°F (24°C), fan speed off of AUTO to save energy.
How To Use Advanced Functions FP function 2 Using this function will cause the unit to operate with a high fan speed setting (while the compressor is on) with temperature automatically set to the lowest setting, 46°F (8°C), in order to achieve faster cooling. NOTE: The function listed below is for heat pump air conditioners only.
How To Use Advanced Functions SET function SET SET OK or Press the SET button to enter the function setting, then press the SET button or the TEMP or buttons to select the desired function. The selected symbol will flash on the display, press the OK button to confirm and this will activate the selected function. To cancel the selected function, just perform the same procedures as above.
DIY® E-Star™ Remote Controller 4 Buttons and Functions Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual. ON/OFF Turns the unit on or off. MODE Scrolls through operation modes in the following sequence: TEMP Increases temperature in 1°F (1°C) increments.
Remote Screen Indicators Remote Screen Indicators Information that is displayed when the remote controller is turned on. Sleep mode display Follow me feature display Transmission: This indicator lights up when the remote transmits a signal to the indoor unit. Wireless control feature display Low battery detection display (If flashes) MODE display Displays the current mode, including: ECO display (some units) Displays when ECO feature is activated.
How To Use Basic Functions How to Use Basic Functions ATTENTION Please ensure the unit is plugged in and power is available before operation. SETTING TEMPERATURE The operating temperature range for units is 62-86°F (17-30°C) or 68-82°F (20-28°C) (model dependent). You can increase or decrease the set temperature in 1°F (1°C) increments by using the the Temperature or buttons on the remote.
How To Use Basic Functions DRY Mode (dehumidifying function) In DRY mode, the unit acts as a dehumidifier. To select DRY mode follow these steps: 1. Press the MODE button and select DRY mode. 2. Set your desired temperature using the TEMPERATURE or buttons. 3. Press the ON/OFF button to start the unit. 1 3 NOTE: FAN speed cannot be set or adjusted in DRY mode. 2 1 3 FAN Mode 1. Press the MODE button and select FAN mode. 2. Press FAN button to select the desired the fan speed: AUTO, LOW, MED, or HIGH. 3.
Setting the Timer Setting the TIMER TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON setting Press TIMER button to initiate the ON time sequence. Press Temperature UP or DOWN Point remote control at the unit button to set the desired time to and wait 1 second, the turn ON the unit. TIMER ON will be activated.
How To Use Advanced Functions How to Use Advanced Functions Swing function Press the SWING button 2s Swing Swing The horizontal louver will swing up and down automatically when pressing SWING button. Press it again to make it stop. Keep pressing the SWING button more than 2 seconds, this will activate the vertical louver swing function (Model dependent). Silence function 2s Pressing the FAN button for more than 2 seconds will activate or disable the Silence function (some units).
How To Use Advanced Functions ECO function Pressing the ECO button will enter the unit into energy efficiency mode. NOTE: This function is only available under the COOL mode. ECO operation: Under COOL mode, press this button and the remote controller will automatically adjust the temperature to 75°F (24°C), fan speed off of AUTO to save energy. However, this only occurs when the set temperature is less than 75°F (24°C).
How To Use Advanced Functions SHORTCUT function Press SHORTCUT button(some units) to revert to previous settings: Pressing the SHORTCUT button when the remote controller is on will cause the system to automatically revert back to the previous settings including the operating mode, set temperature, fan speed level, and the sleep feature (if activated).
How To Use Advanced Functions SET function SET SET OK or Press the SET button to enter the function setting, then press the SET button or the TEMP or buttons to select the desired function. The selected symbol will flash on the display, press the OK button to confirm and this will activate the selected function. To cancel the selected function, just perform the same procedures as above.
Due to updates and constantly improving performance, the information and instructions within this manual are subject to change without notice. Please visit www.mrcool.com/documentation to ensure you have the latest version of this manual.