User Manual
Table Of Contents
- Quick Start
- Safety Information
- Specifications
- Package contents
- Block Diagram
- Rear I/O Panel
- Overview of Components
- Processor Socket
- DIMM Slots
- PCI_E1~6: PCIe Expansion Slots
- M2_1: M.2 Slot (Key M)
- SATA1~6: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- CPU_PWR1, ATX_PWR1: Power Connectors
- JAUD1: Front Audio Connector
- JUSB1~2: USB 2.0 Connectors
- JUSB3: USB 3.2 Gen1 Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- JCOM1: Serial Port Connector
- JCI1: Chassis Intrusion Connector
- JTPM1: TPM Module Connector
- JLPT1: Parallel Port Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JRGB1~2: RGB LED connectors
- EZ Debug LEDs
- BIOS Setup
- Software Description
- RAID Configuration
- Using AMD RAID Controller BIOS Configuration Utility
- Initialize Disks
- Create Arrays
- Delete Arrays
- Swap Arrays
- Manage Spares
- Change the Controller Options
- Booting the system from an array
- Pausing the boot sequence for warning messages
- Change the Staggered Spinup Count
- Using UEFI to create a 2.2TB RAID
- Installing RAID Driver
- Troubleshooting
- Regulatory Notices
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- CPU_PWR1, ATX_PWR1: Power Connectors
- DIMM Slots
- JAUD1: Front Audio Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JFP1, JFP2: Front Panel Connectors
- JLPT1: Parallel Port Connector
- JRGB1~2: RGB LED connectors
- JTPM1: TPM Module Connector
- JUSB1~2: USB 2.0 Connectors
- JUSB3: USB 3.1 Gen1 Connector
- M2_1: M.2 Slot (Key M)
- PCI_E1~5: PCIe Expansion Slots
- Processor Socket
- SATA1~6: SATA 6Gb/s Connectors
37
Overview of Components
JRGB1~2: RGB LED connectors
The JRGB1/2 connectors allow you to connect the 5050 RGB LED strips 12V.
Important
y
The JRGB1/ JRGB2 connector supports up to 2 meters continuous 5050 RGB LED
strips (12V/G/R/B) with the maximum power rating of 3A (12V).
y
Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing the RGB LED strip.
y
Please use MSI’s software to control the extended LED strip.
1
JRGB1/2
JRGB2
Extension cable
5050 RGB LED strips 12V
1
JRGB1/2
1 +12V 2 G
3 R 4 B
JRGB1
EZ Debug LEDs
These LEDs indicate the status of key components during booting process. When an
error is occurred, the corresponding LED stays lit until the problem is solved.
CPU - indicates CPU is not detected or fail.
DRAM - indicates DRAM is not detected or fail.
VGA - indicates GPU is not detected or fail.
BOOT - indicates the booting device is not detected
or fail.