User Manual
Table Of Contents
- Quick Start
- Safety Information
- Specifications
- Package contents
- Block Diagram
- Rear I/O Panel
- Overview of Components
- Processor Socket
- DIMM Slots
- PCI_E1~6: PCIe Expansion Slots
- M2_1: M.2 Slot (Key M)
- SATA1~6: SATA 6Gb/s Connectors
- JFP1, JFP2: Front Panel Connectors
- CPU_PWR1, ATX_PWR1: Power Connectors
- JAUD1: Front Audio Connector
- JUSB1~2: USB 2.0 Connectors
- JUSB3: USB 3.2 Gen1 Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- JCOM1: Serial Port Connector
- JCI1: Chassis Intrusion Connector
- JTPM1: TPM Module Connector
- JLPT1: Parallel Port Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JRGB1~2: RGB LED connectors
- EZ Debug LEDs
- BIOS Setup
- Software Description
- RAID Configuration
- Using AMD RAID Controller BIOS Configuration Utility
- Initialize Disks
- Create Arrays
- Delete Arrays
- Swap Arrays
- Manage Spares
- Change the Controller Options
- Booting the system from an array
- Pausing the boot sequence for warning messages
- Change the Staggered Spinup Count
- Using UEFI to create a 2.2TB RAID
- Installing RAID Driver
- Troubleshooting
- Regulatory Notices
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~4: Fan Connectors
- CPU_PWR1, ATX_PWR1: Power Connectors
- DIMM Slots
- JAUD1: Front Audio Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JFP1, JFP2: Front Panel Connectors
- JLPT1: Parallel Port Connector
- JRGB1~2: RGB LED connectors
- JTPM1: TPM Module Connector
- JUSB1~2: USB 2.0 Connectors
- JUSB3: USB 3.1 Gen1 Connector
- M2_1: M.2 Slot (Key M)
- PCI_E1~5: PCIe Expansion Slots
- Processor Socket
- SATA1~6: SATA 6Gb/s Connectors
59
BIOS Setup
HARDWARE MONITOR
Temperature
& Speed
Fan Manage
Temperature/
Voltage display
Setting
Buttons
f Temperature & Speed
Shows the current CPU temperature, system temperature and fans' speeds.
f Fan Manage
PWM - allows you to select the PWM mode for fan operation.
DC - allows you to select the DC mode for fan operation.
Fan step up/ down time - allows you to set the period of fan step up/ down.
Smart Fan Mode field - allows you to drag the gradient points to configure
the fan target values for Smart Fan mode. Smart Fan can control the fan speed
automatically depending on the CPU temperature to keep it with in a specific range.
If the current CPU temperature reaches to the target value, the Smart Fan function
will be activated.
Important
y
The changing will achieve after you save the changes and reboot the system.
y
Make sure fans are working properly after switching the PWM/ DC mode.
f Settings Buttons
All Full Speed - configures all fans to run at full operating speed.
All Set Default - configures all fans to run at default operating speed.
All Set Cancel - discards current changes and restores previous operating fan
speeds .
f Temperature/ Voltage display
Shows CPU/ system temperature and the current voltages of CPU, system and
memory.