User Manual
Table Of Contents
- Quick Start
- Specifications
- Package contents
- Block Diagram
- Rear I/O Panel
- Overview of Components
- CPU Socket
- DIMM Slots
- PCI_E1~4: PCIe Expansion Slots
- SATA3~6: SATA 6Gb/s Connectors
- M2_1~2: M.2 Slots (Key M)
- JFP1, JFP2: Front Panel Connectors
- JAUD1: Front Audio Connector
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- JUSB3, JUSB4: USB 3.1 Gen1 Connectors
- JUSBC1: USB 3.1 Gen2 Type-C Connector
- JUSB1, JUSB2: USB 2.0 Connectors
- JCOM1: Serial Port Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~3: Fan Connectors
- JCI1: Chassis Intrusion Connector
- JTPM1: TPM Module Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JPWRLED1: LED power input
- EZ Debug LED
- JRGB1~2, JRAINBOW1~2: RGB LED connectors
- Installing OS, Drivers & Utilities
- MYSTIC LIGHT
- Nahimic 3
- BIOS Setup
- RAID Configuration
- Intel® Optane™ Memory Configuration
- Troubleshooting
- Regulatory Notices
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~3: Fan Connectors
- CPU_PWR1~2, ATX_PWR1: Power Connectors
- CPU Socket
- DIMM Slots
- JAUD1: Front Audio Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JFP1, JFP2: Front Panel Connectors
- JPWRLED1: LED power input
- JRGB1~2, JRAINBOW1~2: RGB LED connectors
- JTPM1: TPM Module Connector
- JUSB1, JUSB2: USB 2.0 Connectors
- JUSB3, JUSB4: USB 3.1 Gen1 Connectors
- JUSBC1: USB 3.1 Gen2 Type-C Connector
- M2_1~2: M.2 Slots (Key M)
- PCI_E1~4: PCIe Expansion Slots
- SATA3~6: SATA 6Gb/s Connectors
54
BIOS Setup
fIGD Multi-Monitor [Disabled]
Enables or disables the multi-screen output from integrated graphics and external
graphics card. This item appears when Initiate Graphic Adapter set to PEG.
[Enabled] Enables multi-screen function for both integrated and external
graphics cards.
[Disabled] Disables this function.
f USB Configuration
Sets the onboard USB controller and device function. Press Enter to enter the sub-
menu.
fUSB Controller [Enabled]
Enables or disables all USB controller.
fXHCI Hand-off [Diasbled]
Enables or disables XHCI hand-off support for the operating system without XHCI
hand-off feature.
fLegacy USB Support [Enabled]
Sets Legacy USB function support.
[Auto] The system will automatically detect if any USB device is connected
and enable the legacy USB support.
[Enabled] Enable the USB support under legacy mode.
[Disabled] The USB devices will be unavailable under legacy mode.
f Super IO Configuration
Sets system Super I/O chip parameters including COM ports. Press Enter to enter the
sub-menu.
fSerial (COM) Port 0 Configuration
Sets detailed configuration of serial(COM) port. Press Enter to enter the sub-
menu.
fSerial (COM) Port 0 [Enabled]
Enables or disables serial port.
fSerial (COM) Port 0 Settings [Auto]
Sets serial port. If set to Auto, BIOS will optimize the IRQ automatically or you can
set it manually.
f Power Management Setup
Sets system Power Management of ErP and AC Power Loss behaviors. Press Enter to
enter the sub-menu.
fErP Ready [Disabled]
Enables or disables the system power consumption according to ErP regulation.
[Enabled] Optimize the system power consumption according to ErP
regulation. It will not support S4 & S5 wake up by USB, PCI and PCIe
devices.
[Disabled] Disables this function.