Quick Start Thank you for purchasing the MSI® MPG Z590 GAMING CARBON WIFI/ MPG Z590 GAMING FORCE motherboard. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet. You may have even link to the URL by scanning the QR code.
Safety Information ∙∙ The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly. ∙∙ Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start. ∙∙ Hold the motherboard by the edges to avoid touching sensitive components.
Case stand-off notification Before installing the motherboard into the case, install first the necessary mounting stand-off required for a motherboard on the mounting plate in the case. To prevent damage to the motherboard, any unnecessary mounting stand-off between the motherboard circuits and the computer case is prohibited. The Case standoff keep out zone signs will be marked on the backside of motherboard (as shown below) to serve as a warning to user.
Installing a Processor 2 ⚽⚽ 1 https://youtu.
Installing DDR4 memory ⚽⚽ http://youtu.
Connecting the Front Panel Header ⚽⚽ http://youtu.
Installing the Motherboard 1 ⚽⚽ https://youtu.be/wWI6Qt51Wnc Torque: 3 kgf·cm* 2 BAT1 *3 kgf·cm = 0.3 N·m = 2.
Connecting the Power Connectors ⚽⚽ http://youtu.
Installing SATA Drives ⚽⚽ http://youtu.
Installing a Graphics Card ⚽⚽ http://youtu.
Connecting Peripheral Devices (MPG Z590 GAMING CARBON WIFI) Quick Start 11
Power On 1 2 3 4 12 Quick Start
Contents Quick Start.............................................................................................................. 1 Preparing Tools and Components.......................................................................... 1 Safety Information................................................................................................... 2 Case stand-off notification...................................................................................... 3 Installing a Processor............
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors................................... 40 JBAT1: Clear CMOS (Reset BIOS) Jumper............................................................ 41 JRGB1: RGB LED connector.................................................................................. 42 JRAINBOW1~2: Addressable RGB LED connectors............................................. 43 JCORSAIR1: CORSAIR Connector......................................................................... 44 Onboard LEDs....
Specifications CPU Chipset ∙∙ Supports 10th Gen Intel® Core™ Processors, 11th Gen Intel® Core™ Processors, Pentium® Gold and Celeron® Processors* ∙∙ Processor socket LGA1200 * Please go to intel.com for compatibility information.
Continued from previous column ∙∙ 6x SATA 6Gb/s ports (From Z590 Chipset) ∙∙ 3x M.2 slots (Key M) ▪▪M2_1 slot (From CPU) ▫▫Available only on 11th Gen Intel® CPU ▫▫Supports PCIe 4.0 x4 ▫▫Supports 2242/ 2260/ 2280/ 22110 storage devices Storage ▪▪M2_2* & M2_3** slot (From Z590 Chipset) ▫▫Supports PCIe 3.
Continued from previous column ∙∙ Intel® Wi-Fi 6E AX210 Wireless LAN & Bluetooth® (For MPG Z590 GAMING CARBON WIFI only) ∙∙ The Wireless module is pre-installed in the M.2 (Key-E slot ∙∙ Supports MU-MIMO TX/RX, 2.4GHz/ 6GHz (160MHz) up to 2.4Gbps ∙∙ Supports 802.11 a/ b/ g/ n/ ac/ ax ∙∙ Supports Bluetooth® 5.2, FIPS, FISMA ∙∙ 1x 24-pin ATX main power connector ∙∙ 2x 8-pin ATX 12V power connectors ∙∙ 1x 6-pin PCIE power connector ∙∙ 6x SATA 6Gb/s connectors ∙∙ 3x M.2 slots (M-Key) ∙∙ 1x USB 3.
Continued from previous column ∙∙ 1x Flash BIOS Button ∙∙ 4x USB 2.0 Type-A ports ∙∙ 1x DisplayPort ∙∙ 1x HDMI port Back Panel Connectors ∙∙ 2x USB 3.2 Gen 1 5Gbps Type-A ports ∙∙ 3x USB 3.2 Gen 2 10Gbps Type-A ports ∙∙ 1x USB 3.2 Gen 2x2 20Gbps Type-C port ∙∙ 1x 2.
Continued from previous column ∙∙ Gaming Mode ∙∙ Creator Mode ∙∙ Mystic Light ∙∙ Ambient Link (For MPG Z590 GAMING CARBON WIFI only) MSI Center Features ∙∙ LAN Manager ∙∙ User Scenario ∙∙ Monitor ∙∙ Frozr AI Cooling ∙∙ True Color ∙∙ Live Update ∙∙ Speed Up ∙∙ Super Charger ∙∙ Audio ▪▪Audio Boost 5 ▪▪Sound Tune ∙∙ Network ▪▪2.5G LAN Special Features ▪▪LAN Manager ▪▪Intel Wi-Fi (For MPG Z590 GAMING CARBON WIFI only) ∙∙ Cooling ▪▪M.
Continued from previous column ∙∙ LED ▪▪Mystic Light ▪▪Mystic Light Extension (RAINBOW/RGB/CORSAIR) ▪▪Mystic Light SYNC ▪▪Ambient Link (For MPG Z590 GAMING CARBON WIFI only) ▪▪EZ LED Control ▪▪EZ DEBUG LED ∙∙ Performance ▪▪Lightning Gen 4 PCI-E Slot ▪▪Lightning Gen 4 M.2 ▪▪Multi GPU-CrossFire Technology ▪▪DDR4 Boost ▪▪Core Boost Special Features ▪▪Game Boost ▪▪Lightning USB 20G ▪▪USB 3.
Package contents Please check the contents of your motherboard package. It should contain: Motherboard Documentation Application Cables MPG Z590 GAMING CARBON WIFI/ MPG Z590 GAMING FORCE User manual 1 USB drive with drivers & utilities 1 Quick installation guide 1 SATA 6Gb/s cables 1 LED JRGB Y cable 1 LED JCORSAIR cable 1 LED JRAINBOW cable Wi-Fi antenna (For MPG Z590 GAMING CARBON WIFI only) Case badge Accessories M.2 screw + standoff (2 sets/pack) ⚠⚠Important 1 1 1 M.
Block Diagram PCI_E1 PCIe x16 CPU PCI_E3 PCIe x8 DDR4 2Channel DIMM A1/A2 DIMM B1/B2 M2_1 DMI x8 PCI_E2 USB3.2 Gen2x2 20Gbps PCH PCI_E4 USB 3.2 Gen 2 10Gbps PCI_E5 PCIe x4 SATA2 M2_2 SATA5/6 M2_3 USB 3.2 Gen 1 5Gbps Intel LAN I225 Hub-GL850G USB 2.
Rear I/O Panel USB 2.0 Type-A DisplayPort USB 3.2 Gen 1 (5Gbps) Type-A (For MPG Z590 GAMING CARBON WIFI only) USB 3.2 Gen 2 (10Gbps) Type-A Flash BIOS Button Flash BIOS port Audio Ports 2.5Gbps LAN Optical S/PDIF-Out USB 3.2 Gen 2x2 (20Gbps) Type-C Wi-Fi Antenna connectors ∙∙ Flash BIOS Port/ Button - Please refer to page 56 for Updating BIOS with Flash BIOS Button.
Realtek Audio Console After Realtek Audio Console is installed. You can use it to change sound settings to get better sound experience. Application Enhancement Device Selection Main Volume Connector Settings Jack Status ∙∙ Device Selection - allows you to select a audio output source to change the related options. The check sign indicates the devices as default.
Audio jacks to headphone and microphone diagram Audio jacks to stereo speakers diagram AUDIO INPUT Audio jacks to 7.
Installing Antennas 1. Combine the antenna with the base. 2. Screw two antenna cables tight to the WiFi antenna connectors as shown. 2 1 3. Place the antenna as high as possible.
Overview of Components CPU_FAN1 Processor Socket PUMP_FAN1 JRAINBOW2 CPU_PWR2 CPU_PWR1 DIMMA1 DIMMA2 DIMMB1 DIMMB2 SYS_FAN6 JCORSAIR1 ATX_PWR1 JUSB4 M2_1 SYS_FAN1 PCI_E1 SATA▼1▲2 SATA▼3▲4 BAT1 SATA▼5▲6 PCI_E2 M2_2 PCI_E3 M2_3 SYS_FAN5 SYS_FAN4 JTPM1 JFP2 PCI_E4 JDASH1 PCI_E5 JCI1 JAUD1 JRGB1 JFP1 JBAT1 LED_SW1 JRAINBOW1 SYS_FAN3 JPWRLED1 JTBT1 SYS_FAN2 PCIE_PWR1 JUSB2 JUSB3 JUSB1 Overview of Components 27
Component Contents Port Name CPU_FAN1, PUMP_FAN1, SYS_FAN1~6 Page Fan Connectors 40 Power Connectors 36 CPU Socket LGA1200 CPU Socket 29 JAUD1 Front Audio Connector 35 CPU_PWR1~2, ATX_PWR1, PCIE_PWR1 DIMM Slots JBAT1 JCI1 JCORSAIR1 JDASH1 JFP1, JFP2 JPWRLED1 JRAINBOW1~2 JRGB1 JTBT1 JTPM1 JUSB1~2 JUSB3 JUSB4 LED_SW1 M2_1~3 PCI_E1~5 SATA1~6 28 Port Type Overview of Components Memory slots Clear CMOS (Reset BIOS) Jumper Chassis Intrusion Connector CORSAIR Connector Tuning Controller
CPU Socket Distance from the center of the CPU to the nearest DIMM slot. 50.77 mm Introduction to the LGA1200 CPU The surface of the LGA1200 CPU has two notches and a golden triangle to assist in correctly lining up the CPU for motherboard placement. The golden triangle is the Pin 1 indicator. ⚠⚠Important ∙∙ Always unplug the power cord from the power outlet before installing or removing the CPU. ∙∙ Please retain the CPU protective cap after installing the processor.
DIMM Slots DIMMA1 Channel A DIMMA2 DIMMB1 Channel B DIMMB2 Memory module installation recommendation DIMMA2 ⚠⚠Important DIMMA2 DIMMB2 DIMMA1 DIMMA2 DIMMB1 DIMMB2 ∙∙ Always insert memory modules in the DIMMA2 slot first. ∙∙ To ensure system stability for Dual channel mode, memory modules must be of the same type, number and density.
PCI_E1~5: PCIe Expansion Slots PCI_E1: PCIe 4.0 x16 (From CPU) BAT1 PCI_E2: PCIe 3.0 x1 (From Z590 chipset) PCI_E3: PCIe 4.0 x8 (From CPU) PCI_E4: PCIe 3.0 x1 (From Z590 chipset) ⚠⚠Important PCI_E5: PCIe 3.0 x4 (From Z590 chipset) ∙∙ If you install a large and heavy graphics card, you need to use a tool such as MSI Graphics Card Bolster to support its weight to prevent deformation of the slot.
M2_1~3: M.2 Slots (Key M) ⚽⚽Video Demonstration Watch the video to learn how to Install M.2 SSD. https://youtu.be/2UeWMgjwogU M2_1 M2_2 M2_3 ⚠⚠Important ∙∙ Intel® RST only supports PCIe M.2 SSD with UEFI ROM. ∙∙ Intel® Optane™ Memory Ready for M2_2 and M2_3 slots. Installing M.2 module 1. Loosen the screws of M.2 SHIELD FROZR heatsink. 2. Remove the M.2 SHIELD FROZR and remove the protective films from the thermal pads.
3. Secure the supplied M.2 standoff according to your M.2 SSD length if need. 4. Insert your M.2 SSD into the M.2 slot at a 30-degree angle. 5. Secure the M.2 SSD in place with the supplied M.2 8.5H screw. ⚠⚠Important Skip step 3 and step 5, if you install 22110 M.2 into M2_1 slot or 2280 M.2 into M2_2 and M2_3 slots. 8.5H screw Standoff 4 5 30º 3 6. Put the M.2 SHIELD FROZR heatsink back in place and secure it.
SATA1~6: SATA 6Gb/s Connectors These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device. SATA6 SATA5 SATA4 SATA3 SATA2 SATA1 ⚠⚠Important ∙∙ Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise. ∙∙ SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.
JAUD1: Front Audio Connector This connector allows you to connect audio jacks on the front panel. 1 3 MIC L 10 1 9 MIC R 5 Head Phone R 9 Head Phone L 7 2 SENSE_SEND 2 Ground 4 NC 6 MIC Detection 10 Head Phone Detection 8 No Pin JTBT1: Thunderbolt Add-on Card Connector This connector allows you to connect the add-on Thunderbolt I/O card.
CPU_PWR1~2, ATX_PWR1, PCIE_PWR1: Power Connectors These connectors allow you to connect an ATX power supply. 1 2 3 24 1 13 3 4 6 PCIE_PWR1 ⚠⚠Important 5 6 7 +12V +3.3V 13 +3.3V 3 Ground 15 Ground 5 Ground 17 7 Ground 19 6 +3.3V +5V +5V 8 +12V +12V 1 14 18 Ground 20 10 +12V 22 5VSB +12V -12V PS-ON# PWR OK 9 +12V 16 8 11 1 Ground CPU_PWR1~2 Ground 4 ATX_PWR1 Ground Ground 5 1 4 2 12 8 4 21 23 Ground Ground Res +5V +5V +5V 12 +3.
JDASH1 : Tuning Controller connector This connector is used to connect an optional Tuning Controller module. 6 1 3 5 No Pin MCU_SMB_SCL_M VCC5 2 5 2 4 6 1 NC MCU_SMB_SDA_M Ground JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal (default) Trigger the chassis intrusion event Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2. Close the chassis cover. 3.
JUSB4: USB 3.2 Gen 2 Type-C Connector This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the front panel. The connector possesses a foolproof design. When you connect the cable, be sure to connect it with the corresponding orientation. USB Type-C Cable JUSB1 USB Type-C port on the front panel JUSB3: USB 3.2 Gen 1 Connector This connector allows you to connect USB 3.2 Gen 1 5Gbps ports on the front panel.
JUSB1~2: USB 2.0 Connectors These connectors allow you to connect USB 2.0 ports on the front panel. 1 VCC 3 10 1 9 USB0- 5 USB1+ 8 No Pin VCC USB1- 6 Ground 9 2 4 USB0+ 7 ⚠⚠Important 2 Ground 10 NC ∙∙ Note that the VCC and Ground pins must be connected correctly to avoid possible damage. ∙∙ In order to recharge your iPad, iPhone and iPod through USB ports, please install MSI® Center utility. JTPM1: TPM Module Connector This connector is for TPM (Trusted Platform Module).
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage. The auto mode fan connectors can automatically detect PWM and DC mode. However, you can follow the instruction below to adjust the fan connector to PWM or DC Mode manually.
JBAT1: Clear CMOS (Reset BIOS) Jumper There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory. Keep Data (default) Clear CMOS/ Reset BIOS Resetting BIOS to default values 1. Power off the computer and unplug the power cord. 2. Use a jumper cap to short JBAT1 for about 5-10 seconds. 3. Remove the jumper cap from JBAT1. 4.
JRGB1: RGB LED connector The JRGB connector allows you to connect the 5050 RGB LED strips 12V. 1 3 1 +12V R 2 4 G B RGB LED Strip Connection 1 G R B RGB extension cable JRGB connector 5050 RGB LED strips 12V RGB LED Fan Connection JRGB connector 1 G R B 1 System Fan connector RGB LED Fan ⚠⚠Important ∙∙ The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips (12V/G/R/B) with the maximum power rating of 3A (12V).
JRAINBOW1~2: Addressable RGB LED connectors The JRAINBOW connectors allow you to connect the WS2812B Individually Addressable RGB LED strips 5V. 1 1 3 +5V 2 No Pin 4 Data Ground Addressable RGB LED Strip Connection +5V 1 D JRAINBOW connector Rainbow RGB LED extension cable Addressable RGB LED Fan Connection WS2812B Individually Addressable RGB LED strips 5V JRAINBOW connector 1 1 System Fan connector ⚠⚠CAUTION Addressable RGB LED Fan Do not connect the wrong type of LED strips.
JCORSAIR1: CORSAIR Connector The JCORSAIR1 connector allows you to connect the CORSAIR Individually Addressable Lighting PRO RGB LED strips 5V or CORSAIR RGB fans with the CORSAIR fan hub. Once all items are connected properly, you can control the CORSAIR RGB LED strips and fans with MSI's software.
Onboard LEDs EZ Debug LED These LEDs indicate the debug status of the motherboard. CPU - indicates CPU is not detected or fail. DRAM - indicates DRAM is not detected or fail. VGA - indicates GPU is not detected or fail. BOOT - indicates the booting device is not detected or fail. JPWRLED1: LED power input This connector is used by retailers to demonstrate onboard LED lights.
LED_SW1: EZ LED Control This switch is used to switch on/ off all the LEDs of motherboard. LED_OFF Debug Code LED LED_ON (Default) LED_SW1 The Debug Code LED displays progress and error codes during and after POST. Refer to the Debug Code LED table for details.
Debug Code LED Table SEC Progress Codes 01 Power on.
3C - 3E 4F Post-Memory PCH initialization (PCH module specific) DXE IPL is started PEI Error Codes 50 Memory initialization error. Invalid memory type or incompatible memory speed 52 Memory initialization error. Invalid memory size or memory modules do not match 51 53 54 55 56 57 58 59 5A 5B 5C - 5F Memory initialization error. SPD reading has failed Memory initialization error.
95 PCI Bus Request Resources 97 Console Output devices connect 96 98 99 9A 9B 9C 9D 9E -9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AB AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 - BF PCI Bus Assign Resources Console input devices connect Super IO Initialization USB initialization is started USB Reset USB Detect USB Enable Reserved for future AMI codes IDE initialization is started IDE Reset IDE Detect IDE Enable SCSI initialization is started SCSI Reset SCSI Detect SCSI Enable Setup Verifying Password
D4 PCI resource allocation error.
ACPI States Codes The following codes appear after booting and the operating system into ACPI modes.
Installing OS, Drivers & MSI Center Please download and update the latest utilities and drivers at www.msi.com Installing Windows® 10 1. Power on the computer. 2. Insert the Windows® 10 installation disc/USB into your computer. 3. Press the Restart button on the computer case. 4. Press F11 key during the computer POST (Power-On Self Test) to get into Boot Menu. 5. Select the Windows® 10 installation disc/USB from the Boot Menu. 6. Press any key when screen shows Press any key to boot from CD or DVD...
UEFI BIOS MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface) architecture. The UEFI BIOS firmware infrastructure has many new functions and advantages that traditional BIOS cannot achieve. It will fully support future PCs and devices that comply with UEFI firmware architecture. ⚠⚠Important The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.
BIOS Setup The default settings offer the optimal performance for system stability in normal conditions. You should always keep the default settings to avoid possible system damage or failure booting unless you are familiar with BIOS. ⚠⚠Important ∙∙ BIOS items are continuously updated for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be for reference only. You could also refer to the HELP information panel for BIOS item description.
Resetting BIOS You might need to restore the default BIOS setting to solve certain problems. There are several ways to reset BIOS: ∙∙ Go to BIOS and press F6 to load optimized defaults. ∙∙ Short the Clear CMOS jumper on the motherboard. ∙∙ Press the Clear CMOS button on the rear I/O panel. ⚠⚠Important Be sure the computer is off before clearing CMOS data. Please refer to the Clear CMOS jumper/ button section for resetting BIOS.
Updating the BIOS with MSI Center Before updating: ∙∙ Make sure the LAN driver is already installed and the internet connection is set properly. ∙∙ Please close all other application software before updating the BIOS. To update BIOS: 1. Install and launch MSI CENTER and go to Support page. 2. Select Live Update and click on the Advanced button. 3. Select the BIOS file and click on the Install button. 4. The installation reminder will appear, then click the Install button on it. 5.
RAID Configuration The introduction of RAID levels and types are as below: RAID 0 RAID 1 RAID 5 breaks the data into blocks which are written to separate hard drives. Spreading the hard drive I/O load across independent channels greatly improves I/O performance. provides data redundancy by mirroring data between the hard drives and provides enhanced read performance. provides data striping at the byte level and also stripe error correction information.
Intel® Optane™ Memory Configuration Intel® Optane™ memory is a technology which allows the system to access the data more quickly. It enables the computer to store commonly used data and programs, and keeps them even after powering off the computer. Before you start to install Intel® Optane™ memory, please note that it requires Windows 10 64-bit operating system.
Troubleshooting Before sending the motherboard for RMA repair, try to go over troubleshooting guide first to see if your got similar symptoms as mentioned below. The power is not on. ∙∙ Connect the AC power cord to an electrical outlet securely. ∙∙ Check if all ATX power connectors like ATX_PWR1, CPU_PWR1 are connected from the power supply to the motherboard? ∙∙ Some power supply units have a power button on the rear side, make sure the button is turned on.
Regulatory Notices FCC Compliance Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Electronic Equipment) Statement ENGLISH To protect the global environment and as an environmentalist, MSI must remind you that... Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/ EC, which takes effect on August 13, 2005, products of “electrical and electronic equipment” cannot be discarded as municipal wastes anymore, and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü olacaktır. Avrupa Birliği’ne satılan MSI markalı ürünlerin kullanım süreleri bittiğinde MSI ürünlerin geri alınması isteği ile işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama noktalarına bırakabilirsiniz. ČESKY Záleží nám na ochraně životního prostředí - společnost MSI upozorňuje...
MS-7D06主板产品中有害物质的名称及含量 部件名称 铅 汞 镉 有害物质 六价铬 多溴联苯 多溴二苯醚 ○ ○ ○ (Pb) (Hg) (Cd) (Cr(VI)) 电池** ╳ ○ ○ ○ ○ ○ 外部信号连接头 ╳ ○ ○ ○ ○ ○ 印刷电路板组件* 线材 本表格依据 SJ/T 11364 的规定编制。 ╳ ╳ ○ ○ ○ ○ (PBB) ○ ○ (PBDE) ○ ○: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。 ╳: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求，但所有部件都符合 欧盟RoHS要求。 * 印刷电路板组件: 包括印刷电路板及其构成的零部件。 ** 电池本体上如有环保使用期限标识，以本体标识为主。 ■ 上述有毒有害物质或元素清单会依型号之部件差异而有所增减。 ■ 产品部件本体上如有环保使用期限标识，以本体标识为主。 限用物質含有情況標示聲明書 設備名稱：電腦主機板 單元 電路板 電子元件 金屬機構件
