Instructions / Assembly

This Pre-lit tree includes extra bulbs for any replacements that you
may need to perform on your tree. If extra parts are needed, contact
the Customer Service Team at 1-877-527-0313.
MAINTENANCE
Made in China
Printed in China
This is not a toy, for decorative use only.
1. If the tree does not illuminate, press the 4-Function foot pedal. It
may be in the OFF position.
2. If the top of the tree or another individual lettered section does
not illuminate, remove each section and then reinsert as
instructed, to ensure the electrical connection occurs.
TROUBLESHOOTING
CCT14
Model No. 7207008-62HO / 7207015-62
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY ADDITIONAL
CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A
LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR
CHRISTMAS TREE OR CAUSE PERSONAL INJURY. THIS ACTION WILL
RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
WARRANTY INFORMATION
If for any reason, after assembly, the tree does not light please call
our toll free number 1-877-527-0313.
The limited warranty of this tree applies only to the original
purchaser against manufacturer defects. A valid sales receipt must
be retained as proof of purchase. This product was pre-tested before
shipment and date coded.
The warranty of this pre-lit tree is void when the product is used for
commercial purposes.
Warranty on Lights:
For up to 5 years from the date of purchase, Home Depot will replace
free of charge any manufacturer defect found to the lighted portion
of your tree.
Warranty on Tree:
For up to 5 years from the date of purchase, Home Depot will replace
free of charge any manufacturer defect found to the tree.
Note: After your pre-lit tree is assembled, please check your tree for
any loose or damaged bulbs. Loose or damaged bulbs must be
replaced promptly in order to maintain the performance and life
expectancy of your pre-lit tree. If a bulb burns out, please replace it
at once (see replacement instructions). Failure to replace a burned
out bulb will result in a shorter life span for the remaining bulbs.
Failure to replace burned out bulbs, or misuse of this product will
void the warranty. This Christmas tree is a seasonal product. It is
intended for indoor use only and for temporary (90 days max)
installation and use only. Keep away from heat and moisture.
Carefully unpack all tree components from the carton
(Fig 1). Your tree should include the following:
1 Folding metal tree stand with 3 eyebolts
1 4-function foot pedal with cord and plug; which is
already connected to the lower section “A” of the tree
(Fig 5).
1 Bag of replacement bulbs are included with these
instructions
Tree sections as noted below:
7.5’ tree – 3 sections
9’ tree – 4 sections
PRE-ASSEMBLY
Packaging Contents
Fig 1
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough room
for the tree’s pole from section “A” to be inserted into the
assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
Fig 2
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified by
a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap from the end of the
pole, (that is pinched to a point), and place that end into
the tree stand. Be sure that the pointed end of the pole
extends to the bottom of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
Fig 3
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. The bottom section of your tree contains a cord with a
4-function foot pedal. Remove the twist tie from the cord and
plug into a working electrical outlet. Push the button to select
color change, white, multi or OFF (Fig 6).
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining sections
to light up automatically, upon a firm insertion of each
lettered section (Fig 5).
7. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
8. Remove the protective plastic cap from the end of the pole on
section “B”; insert that end onto the top of the pole of section
“A” (Fig 4).
9. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
10. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
11. Now gently guide the branches of section “B” downward
into place.
12. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is
completely assembled. Each section of the tree is labeled in
alphabetical order beginning from the bottom to the top.
Fig 6
Connection 2
Connection 1
A
B
C
Foot Pedal
Fig 5
CARE AND CLEANING
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the 4-function foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight up
from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift each
section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A” from
the support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse downward,
due to the hinging, aiding in the packing of each section into the
storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold
together; placing in the storage container.
6. It is recommended to always store the tree in a cool, dry location
protected from excessive exposure to heat or sunlight.
NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE
RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION
OF THE TREE WITH THE LED LIGHTS IS RECOMMENDED FOR
INDOOR USE ONLY.
Fig 4
15”
2014 Home Depot MSL
Tree Instruction Sheet - 4-function (English)
Date: 3/13/14
11.5”
7207008-62HO (7.5 ft Mt Everest Spruce)
7207015-62 (9 ft Mt Everest Spruce)