Manual

ManualsBrandsMTD ManualsWalk-behind mowerOfficial MTD gas lawn mower

Operator's Manual

20" Rotary Lawn Mower

Model Series

020

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting

applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have

similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized

service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.

MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722, U.S.A.

PRINTED IN U.S.A. FORM NO. 770-10382

Eco No.1224 (5/2000)

Summary of content (16 pages)

PAGE 1
Operator's Manual 20" Rotary Lawn Mower Model Series 020 IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
PAGE 2
TABLEOFCONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Slope Gauge ...................................................................................................... 6 Hardware Pack .................................................................................................. 7 Assembling Your Lawn Mower ........................................................................... 7 Know Your Lawn Mower ..........
PAGE 3
SECTION1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol--HEED ITS WARNING.
PAGE 4
discharge cover,grasscatcher, bladecontrol handle or 6. Never allow children under 14 years old to operate a othersafety protective devices inplaceandworking. power mower. Children 14 years old and over should Never operate mower withdamaged safetydevices. read and understand the operation instructions and Failure todoso,canresultinpersonal injury. safety rules in this manual and should be trained and 14.Mufflerandenginebecomehotandcancauseabum. Do supervised by a parent. nottouch. 15.
PAGE 5
only,listed in this 4. 5. 6. 7. 8. 9. manual. "Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!" Mower blades are sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing them. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition. Never tamper with safety devices. Check their proper operation regularly.
PAGE 6
USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. ¢# SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST 5" I I O) ¢# o) ¢0 t I O3 ,.< O C 3 ¢0 o O ¢0 8. ¢# 3 o) ¢0 WARNING ,_ .'F Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury.
PAGE 7
SECTION3: HARDWARE PACK B B B B -©©@ -©©® -©©® -©©® Group Group 2 Group 4 @ Group 5 I Group 6 r_ Group 3 SECTION4: ASSEMBLING YOURLAWNMOWER NOTE: This operator's manual covers various models of mowers. Follow only those instructions which pertain to your unit. ToRemoveUnitFromCarton • • • • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. Remove loose parts, if included with unit. Cut along corners and lay carton down flat.
PAGE 8
• Installthehexboltsandflangenutsfromgroup4 of thehardware pack.Usingtwo1/2"wrenches, tightensecurely.SeeFigure2. Route the cable under the lower handle. On the opposite end of the cable housing is a snap fitting. The shaft inside the snap fitting fits in the second hole on the upper handle. Press the snap fitting in place as shown in Figure 4. Make sure that the blade control handle is on top of the upper handle.
PAGE 9
• • • Z Fitting • crown side towards the wheel. See Figure 8. Secure the wheel to the deck with the large bell washer and the nut. • • Repeat on other sides. Remove blocks and put the mower on ground. • SecuringBrakeCable The the mower securely. hardware from group 1 of the hardware pack, axle bolt through the wheel with the hub side wheel facing the deck. See Figure 8.
PAGE 10
KnowYourLawnMower Blade Control Handle Compare the illustration in with your lawn mower to familiarize yourself with the location of various controls and adjustments. Throttle Control Recoil Starter The mower engine is equipped with a constant speed throttle, which is set at full throttle for best performance. Engine / Blade ControlHandle The blade control handle is located on the upper handle of the mower.The blade control handle must be Plug depressed in order to operate the unit.
PAGE 11
• UsingYourLawnMower • _lb For a healthy lawn, never cut more than one-third of the total length of the grass at any one cutting. This mower is designed to operate at full throttle. either the rear deflector or entire grass WARNING: Never operate your unit catcher without assembly in place. WARNING: If you strike a foreign object, stop the engine. Remove wire from spark plug, thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower.
PAGE 12
Wheels • • The wheels require no lubrication. However, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the When sharpening the blade, follow original angle of grind as a guide. It is extremely important to grind off all edges equally to keep the blade balanced. NOTE: wheel with light oil. Engine oil may also be used.
PAGE 13
SECTION8: OFF-SEASON STORAGE The following steps should be taken to prepare lawn mower for storage. • • NOTE: Clean and lubricate mower thoroughly as described in the lubrication instructions. • Refer to engine manual for correct engine storage instructions. • Coat mower's cutting blade with chassis grease to prevent rusting. Store mower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer.
PAGE 14
SECTION10: PARTSLISTFORMODELSERIES020 5\ \ 4 26 15 19, \\\ 8_J; 14
PAGE 15
ModelSeries020 Ref. No. Part No. Description 1. 710-0654A Hex Ind. Washer Screw 3/8-16 xl.0 2. 782-0048 3. 749-1077 Cutting Deck: 20" Lower Handle 4. 749-1076 Upper Handle 5. 747-0976A Control Handle (Bail) 6. 731-0872A Rear Flap 7. 17098 Hinge Clip 8. 710-1044 Screw 3/8-24 x 1.5" Group 8 9. 936-0524A Blade Bell Support 10. 753-0588 Blade Adapter Kit 11. 742-0640 Cutting Blade 12. 731-0064 Discharge Chute 13. 710-0932 Carriage Screw 1/4-20 x 1.0" 14.
PAGE 16
MANUFACTURER'S LIMITED WARRANTY FOR: YARD The limited warranty set forth below is given by MTD PRODUCTS INC ("MTD") with respect to new merchandise purchased and used in the United States, its possessions and territories. MTD warrants this product against defects in material and workmanship for a period of one (1) year commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.