Programming instructions

14-8
Appendix NC Programming 17VRS
DOK-MTC200-NC**PRO*V17-ANW1-EN-P
VI. CEV through MOP
Func-
tion G Group Meaning Description
Page
CEV Cancel NC event
supervision
(Interrupt)
Syntax: CEV: <NC event number>
; CEV must be used to
cancel the supervision (BEV, JEV) of a single interrupting NC
event (0 .. 7).
7-7
D D-correction se-
lection
* modal
Syntax: D<D-correction no. 0..99]>
; D1 .. D99 selects off-
sets defined in the D-correction table. They are activated as
additive tool geometry shifts when activating tool manage-
ment and G48/G49 or G41/G42. D0 cancels active D-correc-
tion offsets.
5-41
DEG Angle unit de-
grees
Syntax: DEG
; Arguments and reciprocal functions of the
trigonometric functions SIN, COS, TAN, and ASIN, ACOS,
ATAN in the angle unit Degrees.
10-5
DEV Disable NC event
supervision
(Interrupt)
Syntax: DEV
; Temporarily disables supervision (BEV, JEV)
of all interrupt. NC events (0 .. 7) until enabled again with
EEV or at the NC program end.
7-7
DP Define process
Syntax: DP <process>
; DP informs the SPS via the corre-
sponding Gateway signal that the process will be required for
NC program execution.
9-2
E Edge selection
* modal
Syntax: E<edge number>
; Selects the data of the defined
tool edge (0 .. 9).
8-2
EEV Enable NC event
supervision
Syntax: EEV
; Enables the supervision (BEV, JEV) of all dis-
abled (DEV) NC events.
7-7
FAX,
GAX
Get axis from
other process
Syntax: FAX (<axis designation>) ,GAX (<process>: <axis
designation>)
; Free AXis for another process; Get AXis of
another process.
9-5
HLT Programmed Halt
Syntax: HLT
; Interrupts NC program execution and the
process waits for a new start signal.
9-8
JEV Jump on NC
event (Interrupt)
Syntax: JEV <label> <NC event number>
; Def. NC event
(0..7) is monitored by the CNC. NC event status of ‘1’ con-
tinues NC program execution at the NC block with the defined
label (not a subroutine).
7-6
JMP Jump to NC pro-
gram
Syntax: JMP <NC program number>
; NC program execu-
tion continues with the first NC block of the defined NC pro-
gram.
9-9
JSR Jump to NC sub-
routine
Syntax: JSR <NC program number>
; NC program execu-
tion continues with the first NC block of the def. NC program
(must end with a RTS, NC subroutine).
9-10
LP Lock process
Syntax: LP <process>
; Command informs the SPS via the
corresponding Gateway signal that the process will be locked
in a user defined state.
9-4
MEN Tool Magazine
(storage) Enable
for manual mode
Syntax: MEN
; Enables the manual tool storage mode while
continuing NC program execution.
8-7
MFP Move Free
Pocket into
change Position
Syntax: MFP(<position>,<direction>) { (.,.) optional }
; Causes tool storage (magazine) movement to bring next
empty location into spec. change pos.
8-6
MHP Tool Storage to
Home Position
Syntax: MHP(<direction>) { (.) optional }
; Causes the tool
storage (turret/magazine) to move to its home (base) position
(pocket 1).
8-3
MMP Move pro-
grammed Loca-
tion into Position
Syntax: MMP(<position>,<direction>) { (.,.) optional }
;
Causes the tool storage (turret/location) to move the location
specified via the T-number in the defined direction to the de-
fined change position.
8-5
MOP Move Old Pocket
into Position
Syntax: MOP(<position>,<direction>, <spindle>) { (.,., )
optional }
; Causes tool storage (magazine) to move the
pocket of the tool in the active tool spindle into the defined
change position.
8-6