ASSEMBLY INSTRUCTIONS r . o x Long ATTACHING THE UPPER |A GUIDE ASSEMBLY Flat Washer 5HE™ LD, '} Hex Lock A Nut Thread Hex Bolt {IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: To determining right and feel band sides of your shredder stand behind and face the hopper.
WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the shredder. Hex Bolt Chute D elector Flat Washer Hex Lock Nut FIGURE 3, Hopper Asset ably Hopper Pivot m\ Door. Assemble This Truss Screws Truss Screw and and Nuts . /"3 prep. Guide Extension Remove Truss Screw and Nut = Upper Guide Assembly: el ATTACHING THE CHUTE DEFLECTOR (See Figure 2} 1.
FIGURE 5. ATTACHING THE CATCHER BAG Your shredder is equipped: with a catcher bag few-caleh the shredded material. To attach the bag, place the opening of the bag over. the chute deflector so-it completely covers the chute opening: Depress the plunger on the drawstring, .pull on the drawstring until the bag is tight around the chute opening: Release plunger fo fog it into position, .See figure & OPERATION KNOW YOUR SHREDDER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER.
BEFORE STARTING 1. Place the shredder on a firm. level surface: 2. Service engine with gasoline and oif as instructed i the: separate engine manual packed pith your: shredder, 3. Attach spark pig wire to spark plug: NOTE: Check the fuel level periodically 1o a rood ramming ot of gasoline while operating the shredder. i the unit runs out of gas as it ds shredding. or chirping, Wilma be necessary 1o unclog the unit before caliber respelled. ‘Refer to "Removing the Flail Sc.oen™ on page 8.
No:Larger Than v 12" Diameter FIGURE 10. To lower the hopper assembly, use one hand to grasp the handle at the tap of-the-hopper assn: bly and it sightly. Pull 43 'on the release bar, and lower ihe hopper assembly 1o the ground: Release the bar. See figure 11 3.
mended at-the start of ‘each season; check engine manual for.correct plug type and .gap specificity sons. Clean the engine regularly with: aiclothio® burgh: Keep the cooling system {(blower housing areal clean o permit proper:air circulation ‘which:is essential to engine performance and life.
NOTE: When reassembling, make ‘certain the opening on the back-up plate is: toward. the bottom of the Lol The-back-up plate may be reversed io provide 4 new clotting edge: Torque Wrench Blade FIGURE 15 4. Loosen the two hand knobs and cupped washers which secure the chute deflector, ‘and raise the chute deflection 8. Keep the impeller assembly from turning by inserting a 1/2% or 3/4" diameter pipe through the w flail screen.
242-645, 242-648, 242A645, 2427648 PARTS LIST FOR SHREDDERS: AER ART | cob DESCRIPTION RN lemme DESCRIPTION 117450571 | N Bladed > Mott SUE 40 1 710:0380 Hex Bolt x 1.75" Lg.* 13481 Blade 411 681-0004 2N Flail Housing 7100818 Hex BOR x 2.0V 781-0474A1 N | Fla ll Housing Q7140114 S Key Ly 431 735:0638 Spark Plug Boot (Optional L Wash: 382 Engine Fl-Wash: 406" 45:1 747-0531A Heloise Bar O.D: Hen. 46 | 732:0646 Torsion Lg. 8 L4508 Flail 475 712-0429 Elastic Lock Nut Tha.
