Operator's Manual Log Splitter Model Series 500 & 510 IMPORTANT: Read safety rules and instructions carefully before operating equipment.
TABLEOFCONTENTS Content Page 3 5 7 8 Important Safe Operation Practices Assembling Your Log Splitter Know Your Log Splitter Operating Your Log Splitter Adjusting Your Log Splitter 10 Content Maintaining Your Log Splitter Storing Your Log Splitter Trouble Shooting Illustrated Parts List Warranty Page 10 12 12 14 16 FINDINGMODELNUMBER This Operator's Manual is an important part of your new log splitter. It will help you assemble, prepare and maintain the unit for best performance.
SECTION1: IMPORTANT SAFEOPERATION PRACTICES _. ARNING" points out important safety Read instructions which, if not followed, could endanger personal safety This and/orsymbol property of yourself and others. and follow all instructions in this manual beforethe attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
modifications such as taillights, etc., needed to comply, is the sole responsibility of the purchaser. If a "Statement of Origin" is required in your state, see your local dealer. 16. Do not tow machine faster than 45mph. 17. See Transporting the Log Splitter section in this manual for proper towing instructions once all federal, local, or state requirements are met. Operation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Before starting this machine, review the "Safety Instructions".
SECTION2: ASSEMBLING YOURLOGSPLITTER UnpackingfromCrate AttachingtheTongue • • • • • Pry top, sides, and ends off the crate. Set panels aside to avoid tire puncture or personal injury. Remove and discard plastic bag that covers unit. Remove any loose parts if included with unit (i.e., operator's manual, etc.) Cut and remove straps which secure parts to bottom of crate. Unbolt any remaining parts which may be bolted to the bottom of the crate. this machine.
• Disconnect the log cradle from the beam on the side of the control valve. See Figure 4. PreparingtheLog Splitter • • Lock Washer Hex Nut • Lubricate the beam area (where the splitting wedge will slide) with engine oil; do not use grease. Remove vented reservoir dipstick or pipe plug, as the case may be, located in front of the engine on top of the reservoir tank. See Figure 6. Fill the reservoir tank with Dexron III automatic transmission fluid or 10W AW hydraulic fluid.
SECTION3: KNOWYOURLOGSPLITTER Compare the illustration in Figure 7 below with the controls on your log splitter, and get familiar with its features before starting to operate. Know how to stop the machine quickly in the event of an emergency. Cylinder How it works \ \ Hitch Assembly Control Handle Reverse J .," (Automatic) lTo return wedge ,1 I Beam Assembly Neutral l I _X \ HandleForward I_---_ (Manual) Tongue To stop I weage To split wood Jack Stand Horizontal Beam Lock Cradle Vertical Be
SECTION4: OPERATING YOURLOGSPLITTER WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. WARNING: Wear leather work gloves, safety shoes, ear protection, and safety glasses when operating a log splitter. Ensure safe footing. GasandOilFill-Up • _IL Service the engine with gasoline and oil as instructed in the engine manual packed with your log splitter. Read instructions carefully. handling gasoline.
• • To lock the beam in the vertical position, pullouton the vertical beam lock and rotate it to secure the beam. See Figure 7. Stand in front of the unit to operate the control handle and to stabilize the log. See Figure 8A. A RaisingandLowering Beam • B Use control handle to run wedge up and down beam 6 to 8 times to circulate the hydraulic fluid, which will warm and thin the fluid. Place log splitter on a firm, level surface.
NOTE: Use caution when backing up. It recommended to use a spotter outside the vehicle. _ Check ARNING" local, state, Do not andtow federal fasterrequirements than 45mph. before towing on any public road. SECTION5: ADJUSTING YOURLOGSPLITTER NOTE: The gibs may be rotated and/or turned over for even wear. _ ARNING" without Do notfirst at any time make any adjustments stopping engine, disconnecting spark plug wire, and grounding it against the engine.
• • • • Maintain fluid level at all times within the range specified on the dipstick, or within 3-3.5" from top edge of the pipe. Change the hydraulic fluid in the reservoir every 100 hours of operation. Disconnect the suction hose from the bottom of the reservoir tank and drain the fluid into a suitable container. Refill using only Dexron III automatic transmission fluid or 10W AW hydraulic fluid.
SECTION7: STORINGYOURLOGSPLITTER Prepare your log splitter for storage at the end of the season or if the log splitter will not be used for 30 days or more. • • in the fuel tank inside WARNING" Never of store building machine where with fumes fuel may reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc. • • • • • Clean the log splitter thoroughly.
HydraulicCylinder:Troubleshooting Problem Cylinder rod will not move Cause Remedy 1. Broken drive shaft. 1. See authorized service dealer. 2. Shipping plugs left in hydraulic hoses. 2. 3. 3. 4. Set screws in coupling not adjusted properly. Loose shaft coupling. 5. 6. 7. 8. Gear sections damaged. Damaged relief valve. Hydraulic lines blocked. Incorrect oil level. 5. 6. Disconnect hydraulic hoses, remove shipping plugs, reconnect hoses. See operator's manual for correct adjustment.
SECTION9: PARTSLISTFORMODELSERIES500 AND510 72 75 14 11 79 15 12 16 9 j. 19 4( 49-L_._ :,_ 23 C "<,,::2_'_@_t, so__...j'._, b-..%,/51 8 458__ -_23 81 43 29 57_ 54._ 44 __53 A 30 27. 63 26 45 4O 64.
ModelSeries500 and510 Ref. No. Part No. Ref. No. Part Description Part No. Part Description 1. 718-o773 Hydraulic Cylinder 42. 781-0682 Log Tray 2. 727-0634 Hydraulic Tube 43. 681-0161 3. 710-1018 Hex Cap Screw 1/2-20 x 2.75 44. 710-0521 Frame Assembly Hex Bolt 3/8-16 x 3" 4. 737-0192 90 Degree Solid Adapter Control Valve 45. 719-0353 46. 714-0122 Coupling Shield Square Key 3/16" x.75 5. 6. 718-0481 737-0153 Return Elbow 47. 718-0686 7. 737-0238 Nipple Pipe 1/2-14 48.
MANUFACTURER'S LIMITED WARRANTY The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. "MTD"warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.