OPERATOR'S MANUAL Log Splitter Model Series 550 thru 570 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
TABLEOFCONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Assembling Your Log Splitter ............................................................................. 5 Know Your Log Splitter ...................................................................................... 7 Operating Your Log Splitter ................................................................................ 8 Adjusting Your Log Splitter ........
SECTION1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
g. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change immediately. a. Use only an approved gasoline container. b. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. c. Neverfuel machine indoors. d. e. f. g. h. i. j.
8. Foryoursafety,replacealldamaged orwornparts immediately withoriginalequipment manufacturer's (O.E.M.)partsonly."Useofparts whichdonotmeettheoriginalequipment specifications mayleadtoimproperperformance andcompromise safety!" 9. Donotalterthismachineinanymanner,alterations suchasattachinga ropeor extension tothecontrol lever,oraddingtothewidthor heightofthewedge mayresultinpersonalinjury.
Vertical Lock Clevis Remove Log (Operating Figure 1 AttachingThe Tongue(See Figure2) With the log splitter still standing upright, remove two hex bolts, lock washers, and hex nuts from the end of the tongue. Align the holes in the tongue with the holes in the tank bracket and secure with hardware just removed. NOTE: High pressure hose must be above the tongue assembly.
Dipstick Figure 6 Figure 5 Fill the reservoir tank with Dexron III automatic transmission fluid or 10W AW hydraulic fluid. Check fluid level using the dipstick. See Figure 6. Do not overfill and replace vented dipstick securely. The dipstick should be tighten until the top of the threads are flush with the top of the pipe. NOTE: The reservoir tank has a capacity of 3 1/2 gallons.
NOTE:Certain engines may also be equipped with an on/offswitch, Disconnect spark plug wire and ground against the engine to prevent unintended starting. Reverse Neutral ,q Control Handle _Forward -Splitting Wedge Horizontal Position Lock Vertical Position Lock Figure 7 SECTION4: OPERATING YOURL0GSPLITTER all instructions and warnings on the WARNING: Read, understand, and follow machine and in this manual before operating.
Use Dexron III Automatic Transmission Fluid or 10W AW hydraulic fluid. Use a filter (clean or replace regularly) Use a breather cap on fluid reservoir. Make certain pump is mounted and aligned propedy. Use a flexible "spider" type coupling between engine and pump drive shafts. Keep hoses clear and unblocked. Bleed air out of hoses before operating. Flush and clean hydraulic system before starting after any malfunction or servicing. Use "pipe dope" on all hydraulic fittings.
If coupler hitch does not fit on ball, turn adjustment nut one turn counter-clockwise. Transporting The Leg Splitter Lower the beam to its horizontal position. Make certain the beam is locked securely with the horizontal beam lock. If coupler hitch is too loose on ball, turn adjustment nut one turn clockwise. Connect the safety chains to the towing vehicle. Do not tow faster than 45mph and check local, state, and federal requirements before towing on any public road.
Drainthefluidandflushthereservoirtankandhoses withkerosene whenever anyrepairworkisperformed onthetank,hydraulic pumporvalve.Contaminants in thefluidwilldamagethehydraulic components. Remove the pump. Rotate the engine by slowly pulling starter handle until engine coupling half set screw is visible. Loosen set screw using allen wrench and slide coupling half off of engine shaft. Loosen set screw on pump coupling half and remove coupling half.
WARNING: Drain fuel into an approved container outdoors, away from an open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel. Fuel left in engine for extended periods deteriorates and will cause starting problems. StoringYourLogSpliUer Clean the unit thoroughly. Wipe equipment with an oiled rag to prevent rust. Refer to engine manual for correct engine storage instructions. Store unit in a clean, dry area.
SECTION8: TROUBLESHOOTING Problem Engine fails to start Cause 1. 2. 3. Engine overheats Spark plug wire disconnected. Fuel tank empty or stale fuel. Throttle control lever not in correct 1. 2. 3. Connect wire to spark plug. Fill tank with clean, fresh gasoline. Move throttle lever to FAST position. 4. Move choke to CHOKE position. 5. 6. Prime engine. Clean fuel line. 5. 6. starting position. (If Equipped) Choke not in CHOKE position. (If Equipped) Engine not primed properly. Blocked fuel line.
HYDRAULIC TROUBLESHOOTING Cause Problem Cylinder rod will not move Remedy 1. 2. Broken drive shaft. Shipping plugs left in hydraulic hoses. 1. 2. 3. 3. 4. Set screws in coupling not adjusted properly. Loose shaft coupling. 5. 6. 7. 8. Gear sections damaged. Damaged relief valve. Hydraulic lines blocked. Incorrect oil level. 5. 6. See authorized service dealer. Disconnect hydraulic hoses, remove shipping plugs, reconnect hoses. See operator's manual for correct adjustment.
Notes 15
ModelSeries550 thru570 2 / 16 28 / .30 B 48 7O 74 / 45 \ z\ / 16 \ \ 75 \ \ /
ModelSeries550 thru570 Refl No. Part No. Part Description Part No. 1. 718-0769 Hydraulic Cylinder 42. 712-0431 2. 727-0634 Hydraulic Tube 43. 781-0682 Flanged Lock Nut 3/8-16 Log Tray 3. 710-1018 Hex Cap Screw 1/2-20 x 2,75 44. 781-0686 Log Tray Bracket 4. 737-0192 781-0526 90 Degree Solid Adapter Hose Guard 45. 46. 681-0161 726-0214 Frame Assembly 5. 6. 737-0153 Return Elbow 47. 732-0583 7. 718-0481 781-0538 710-0515 48. 49.
MANUFACTURER'S LIMITED WARRANTY the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in c. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake adjustments, clutch adjustments or deck adjustments; and normal deterioration of the exterior finish due to use or exposure. d.
