Manual

®
Y25
2-Cycle Trimmer
Operator'
RemovingUnitFromCarton
Remove all contents from
carton.
AssembleThe Unit
Bracket
]
L
]
No Tools Required!
Starter Rope
On/Off Switch
Slide shield's slot onto
mounting bracket. Rotate
shield onto shaft. Push
square bolt through shield
and bracket. Tighten
washer and wing nut
onto bolt.
Put D-handle on shaft. Move
handle a minimum 6 inches
away from shaft grip. Insert
clamp bolt and tighten the
wing nut.
D-Handle
Throttle Control
AssembleThe Unit
f
1 Gallon 3.2 oz
1 J
E]
Mix thoroughly in separate
fuel can:
- 3.2 ft. oz. of 2-cycle
engine oil
- 1 galmon of unleaded
gasoline
NOTE: Do not mix directly in
fuel tank.
Place unit on a level
surface. Fill fuel tank.
]
Starting The Unit
_rimer '=fr ACL" L
Bu_ ......
]
10X
Press primer bulb 10 times,
or until fuel is visible
1--
ChokeLever i
Move choke lever to
Position 1.
]
Need Help?
Call 1-800-800-7310
DIDN'T START?
Repeat these instructions.
IF engine fails to start after2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF unit still fails to start, refer to the
operator's manual for additional starting
and troubleshooting information
Starting The Unit
[--1
Crouch in starting position.
SQUEEZE and HOLD
throttle for ALL further
steps.
Pull rope 5 times.
]
j
Move choke lever to
Position 2 and squeeze
throttle.
]
: 35xj
F]
Pull rope 34 times to start
engine. Run unit for 30-60
seconds to warm up.
r E
Choke Lever
Continue to squeeze
throttle. Move choke lever
to Position 3.
]
Continue to squeeze
throttle. Run unit for an
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
n
I
,,C
_m
C
uJ
m
m
LO
n
I
C
U,
m
Reloading The Line*
Bend short end and push it
into the other hole. Pull tight.
E]
insert 10' of 0,080"
SplitLine ® through hole in top
of reel. Pull most of line
through hole until 3"-4"
remains.
Replacement SplitLine c_:
Part #49U0134K953
For single line installation, refer to Line Installation
section of this manual
j ) J
Wind line tightly in direction Push 6"-7" ends into 0.080" Insert or slide lines into the Pull lines firmly to release
of arrow. Split other end of holding slots, eyelets in spool. Insert spring from holding slots.
®
SplitLine back 6"-7". and reel into spool.
F]
O
n
I
m
O
_C
o_
¢0
uJ
f _ SP oolE
Spring
_ nner
Reem
Unscrew bump knob
counterclockwise. Remove
inner reel and spring.
Reloading The Line
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
f
For replacement spool installation, refer to
Installing a Prewound Reel section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
NEED HELP? CALL 1-800-800-7310 iN U.S. OR 1-800-668-1238 iN CANADA
PART NO. 769=06169 P00 (6/10}