Operator's Manual 21" Self Propelled Mulching Mower Model 565 IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
TABLEOFCONTENTS Content Page 3 6 7 9 Important Safe Operation Practices Slope Gauge Assembling Your Lawn Mower Know Your Lawn Mower Operating Your Lawn Mower Maintaining Your Lawn Mower 10 11 Content Service & Adjustments Off Season Storage Trouble Shooting Illustrated Parts List Page 13 14 15 16 Warranty 20 FINDINGMODELNUMBER This Operator's Manual is an important part of your new lawn mower, tt will help you assemble, prepare and maintain the unit for best performance.
SECTION1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol--HEED ITS WARNING.
yourfooting,releasethebladecontrolhandle 2. Do not mow slopes greater than 15 degrees as immediately andthebladewillstoprotatingwithin shown on the slope gauge. threeseconds. 3. Do not mow on wet grass. Unstable footing could 9. Mowindaylightorgoodartificiallight;walk,notrun. cause slipping. 10.Stopthebladewhencrossinggraveldrives, walkwaysorroads. Children 11.
9. Neverremovegascapor addfuelwhiletheengine is hotor running.Allowenginetocoolatleasttwo minutesbeforerefueling. 10.Neveroverfillfueltank.Filltanktonomorethan½ inchbelowbottomoffillernecktoprovidespacefor fuelexpansion. 11.Replacegasolinecapandtightensecurely. 12.If gasolineis spilled,wipeitofftheengineand equipment. Moveunittoanotherarea.Wait5 minutesbeforestartingtheengine. 13.
SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE m,ll A POWER POLE A CORNER OF A BUILDING m OR A FENCE POST I I I £o !t 15 ° L ,_ WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting in serious injury.
SECTION3: ASSEMBLING YOURLAWNMOWER Raise the lower handle in the direction shown in RemovingUnitFromCarton • • • • Figure 1 (step 2) till it snaps into place. Raise the upper handle in the direction shown in Figure 1 (step 3). Tighten the wing nuts which are already on the handle. See Figure 2. Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open. Remove loose parts included with unit (i.e., operator's manual, oil, etc.). Cut corners and lay carton down flat.
AttachingStarterRope The rope guide is already attached to the right side of the upper handle of your mower. See Figure 4. • • With spark plug wire disconnected and grounded, hold the blade control handle against the upper handle, and pull the starter rope out of the engine. Slip the rope through the rope guide as shown below. Tighten the wing nut holding the rope guide to the upper handle.
SECTION4: KNOWYOURLAWNMOWER Read this owner's manual and safety rules before operating your lawn mower. Compare the illustrations in Figure 8 with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Starter Rope The starter rope is attached to the handle. Stand behind the unit and pull the starter rope to start the unit. BladeControl Handle The blade control handle is located on the upper handle of the mower.
SECTION5: OPERATING YOURLAWNMOWER ToStopEngine _ instructions ARNING: andRead warnings and understand on the machine all and in this manual before operating. • Release the blade control handle to stop the engine and blade. • Disconnect spark plug wire and ground it against the engine to prevent accidental starting while equipment is unattended. Gas& OilFill-Up • • ,_ Check oil level and add oil if necessary. Follow relevant instructions in the engine manual for this.
SECTION6: MAINTAININGYOURLAWNMOWER • _ ARNING:the Always stopwire the before engine and disconnect spark plug performing any maintenance work or adjustments on your lawn mower. Inspect muffler periodically, and replace if necessary. Damaged mufflers or spark arresters can create a fire hazard. _h ARNING: surrounding areas while the Avoid mowermuffler engineand is hot because temperature of these areas of the engine may exceed 150 ° F.
BladeControl • To ReplaceBlade: • Before reinstalling the blade-pulley assembly to the unit, lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. • Also lubricate the bolt hole and the hex bolt. Lubricate the pivot points on the blade control handle and the brake cable at least once a season with light oil. The blade control must operate freely in both directions.
SECTION7: SERVICE& ADJUSTMENTS Tighten the screw, loosened earlier, to secure the belt tension spring to the transmission, and reassemble the front drive cover. ReplacingDriveBelt • Remove two shoulder screws securing the front drive cover to the mower deck. See Figure 11.
For rough or uneven lawns, move the height adjustment handles to higher cutting height position. Height Adjustment Lever Notch Lower Handle Figure 14 Reassemble the upper handle to the lower handle. Place the hairpin clips in the inner holes of the weld pins and replace the carriage bolts and wing nuts on the handle brackets. Attach the starter rope as instructed in the Assembly section.
SECTION9: TROUBLE-SHOOTING Problem Engine fails to start Engine runs erratic Possible Cause Corrective Action 1. 2. 3. 4. Blade control handle disengaged Spark plug wire disconnected Fuel tank empty, or stale fuel Blocked fuel line 1. 2. 3. 4. Engage blade control handle. Connect wire to spark plug. Fill up tank with fresh gasoline. Clean fuel line. 5. 6. Faulty spark plug Engine flooded 5. 6. Clean, adjust gap, or replace. Wait a few minutes to restart. Do not prime. 1. 2.
SECTION10: PARTSLIST FORMODEL565 1. 22 \\\\\\ j3 •. 16 17 52 23 53 25 / 79 / /' Z 2q 6o 34 \6 43 34 IMPORTANT: For a proper working Factory Approved Parts. V-BELTS designed to substitute (non not disengaging engage and OEM) V-Belt disengage \ \ _9 machine, use are specially safely. can be dangerous completely.
Model565 Ref. No Part No. Ref. No Description 1. 747-1214 Lower 2. 710-0599 TT Screw 3. 736-0270 Bell Washer.265 4. 17032A Deflector 5. 732-1014 Torsion & 756-04017 Input Pulley 7. 747-1161A Blade Control 8. 749-1092A Upper Handle 9. 731-04177 Chute Deflector 10. 687-02055 Mulch Plug Complete 52. Pin 11. 747-0710 Hinge 12. 732-0708 Bearing Description 43. 687-02044 Pivot Plate Assembly 44. 710-1257 Hex Screw 3/8-24 x 0.75 45.
NOTES 18
NOTES 19
MANUFACTURER'S LIMITED WARRANTY FOR: YaRD-MaN) The limited warranty respect United States, workmanship date of original replace, materials if this product product, against has been operated vandalism, peril or natural installation repair theft, improper Damage will void your warranty Normal wear parts are warranted Replacement g.
