Operator`s manual

22
6
Maintaining
Your Lawn
Tractor
WARNING
Periodically inspect
the blade spindles for
cracks or damage,
especially if you strike
a foreign object.
Replace immediately
if damaged.
Be sure to shut the
engine off, remove ig-
nition key, disconnect
the spark plug wire(s)
and ground against
the engine to prevent
unintended starting
before removing
the cutting blade(s)
for sharpening or
replacement. Protect
your hands by using
heavy gloves or a rag
to grasp the cutting
blade.
6. Repeat the above steps on the tractor’s right side.
NOTE: The deck support rod on the right side of the
tractor is secured using hair pin clip as opposed to a
cotter pin, which you might had noticed was used on the
left side. This is normal and should be reinstalled in the
same manner as removed.
7. Move the deck lift lever into the top notch on the right
fender to raise the deck lift arms up and out of the way.
8. On 38” & 46” Decks: Gently slide the cutting deck
toward the front of the tractor allowing the hooks
on the deck to release themselves from the deck
stabilizer rod.
On 42” Decks: Remove the bow-tie cotter pin
securing the deck stabilizer rod to the deck. Slide the
deck lift rod from the mounting weldment on the deck
as seen in Figure 6-6.
• Aftercleaningthebatteryandterminals,applyalight
coat of petroleum jelly or grease to both terminals.
• Alwayskeeptherubberbootpositionedoverthe
positive terminal to prevent shorting.
IMPORTANT: If removing the battery for any reason,
disconnect the NEGATIVE (Black) wire from it’s terminal
first, followed by the POSITIVE (Red) wire. When re-
installing the battery, always connect the POSITIVE (Red)
wire its terminal first, followed by the NEGATIVE (Black)
wire. Be certain that the wires are connected to the correct
terminals; reversing them could change the polarity and
result in damage to your engine’s alternating system.
Charging
IMPORTANT: When charging your tractor’s battery, use
only a charger designed for 12V lead-acid batteries. Read
your battery charger’s Owner’s Manual prior to charging
your tractor’s battery. Always follow its instructions and
heed its warnings.
If your tractor has not been put into use for an extended
period of time, charge the battery as follows:
• Setyourbatterychargertodeliveramaximumof10
amperes. If your battery charger is automatic, charge
the battery until the charger indicates that charging is
complete.
NOTE: If the charger is not automatic, charge for no fewer
than eight hours.
WARNING: Batteries give off an explo-
sive gas while charging. Charge battery
in a well ventilated area and keep away
from an open flame or pilot light as on
a water heater, space heater, furnace,
clothes dryer or other gas appliances.
Jump Starting
WARNING: When removing or installing
the battery, follow these instructions to
prevent the screwdriver from shorting
against the frame.
Figure 6-7
9. Carefully remove the PTO cable from the rear of
the cutting deck by removing the hair pin clip which
secures it. Remove the spring from the deck idler
bracket. See Figure 6-7.
10. Gently slide the cutting deck (from the left side) out
from underneath the tractor.
Tires
WARNING: Never exceed the maxi-
mum inflation pressure shown on the
sidewall of tire.
The recommended operating tire pressure is:
• Approximately10psiforthereartires
• Approximately14psiforthefronttires
IMPORTANT: Refer to the tire sidewall for exact tire
manufacturer’s recommended or maximum psi. Do not
overinflate. Uneven tire pressure could cause the cutting
deck to mow unevenly.
Battery
The battery is sealed and is maintenance-free. Acid
levels cannot be checked.
• Alwayskeepthebatterycablesandterminalsclean
and free of corrosive build-up.
Figure 6-6